How To Repair a Hollow Door

House On the Mend
25 followers
3 Video Views·Feb 2, 2026
In this video you will learn how to repair a hole in a hollow core interior door. The materials used for the repair are commonly found at any home improvement store.
Vaughan BS240P Hand Saw used in video: https://amzn.to/2W2fVDN
Great Stuff Spray Foam: https://amzn.to/2ZJWrBx
DAP joint compound: https://amzn.to/2KstaaM
Bates Spackling Knife set: https://amzn.to/31L3hIF
3M Sanding blocks: https://amzn.to/2XwFQ6M
3M 220 grit sandpaper: https://amzn.to/2IZfPmZ
Kilz brand primer: https://amzn.to/2WWv4qS
Follow us on Instagram: https://www.instagram.com/homvegas/
Website: www.houseonthemend.com
Send correspondence to:
House On the Mend
7582 S Las Vegas Blvd Suite 189
Las Vegas, NV 89123
I would love to read your video requests in the comments below.
Hi, I'm Mike with House on the Men and in this video we're going to be repairing this hole
in this interior hollow core door. So let's zoom in and get started. All right, so as you can see
here we have a complete puncture of this door and several pieces that were broken off when
the skateboard in this case hit it and we have these cracks heading off in four directions.
Now on the bottom of this door and along both sides and the top is solid wood.
Most of your interior doors these days are what they call hollow core, meaning there's just a
frame and maybe some cross bracing across that these thin laminates are applied to
and that's how you get a nice lightweight door. Now these doors here are at the end of a long
hallway and they're really tall, eight feet high doors, so they would be really heavy if they were
solid. Now the basic steps for repairing this door are going to be to fill this void with some spray
foam insulation so that we'll have backing material to apply a joint compound or other
spackling over this area, wait for that to dry, sand it, and then repaint it. Now all these steps
could be accomplished right here with the door hanging in its place, but it's really
uncomfortable to be laying down on the floor like this, so what we're going to do is take the door
off by popping out these hinge pins and take this out into the garage and start working on it.
So the best way to remove a door is not to unscrew it from the hinges but to knock out the hinge pin
that connects both sides of the hinges together, and that's pretty simple. You just get a nail set
or a phillips screwdriver and a hammer and you just tap that pin right out. You do that to all
the hinges, most doors have three, this one's pretty tall so it's got four, but you remove
that and then you're just able to pull the door right off of the hinges that are set inside the
and take it out to wherever you need to work on it. All right, so we got the door out in the garage
and it's sitting on a table with a moving blanket to protect it from getting scratched.
I reached inside and I grabbed out whatever debris I could find and removed all of that.
So if you take a closer look here you can see these cracks make this laminate very, very
flexible. So we're going to do a few things to strengthen this portion as well as fill up this
gap so that we can put down some joint compound or some spackling. First thing we're going to do
is we're going to take a pocket knife or a razor blade and we are going to prep all of these
cuts here, all of these edges. If you look at the way they ripped when that skateboard hit,
all of these edges are coming back like this. We want to take a knife and
prep these edges in the reverse like this.
See that? Now I'm beveling it down this way instead of a sharp edge on the outside. I'm
beveling it down and that way when we end up putting spackling on there'll be a nice smooth
transition into the spackling rather than this being the leading edge and really sharp. The
will fill that void that we're going to create with the knife. Then we're going to take this
paper and we're going to stuff that in around this area to create like a kind of a half moon here.
So we'll have the frame that's right here and then we'll have the paper come around this way
and then when we fill with our spray foam in here and it expands, it won't be expanding all over.
It will be expanding right in this concentrated spot and it'll be coming out of the hole and then
we'll let that dry. That way we'll come back and we'll cut off that foam creating a little recess
impression or indentation and that will be the final area that we start putting down
joint compound or spackling. So let's prep all these edges now. That looks pretty good.
Next we'll take this wrapping paper and we'll stuff it in this hole and make a half moon
kind of shape out of it and that will give us a good area for the spray foam to pool.
All right, got that stuffed in there. Now let's start moving it this way and pushing it up this
way so we create that perfect pooling area for the foam. Now we're going to take this
spray foam insulation. This is great stuff. Widely available everywhere. Works great.
Just cut open the plastic here. Get our little straw. First thing we want to do is shake well
then apply our straw. Then I've learned the hard way you always want to have
rubber gloves on when you're working with this spray foam insulation. All right, keep the can
upside down and let's just get some of this spray foam going in here. It isn't going to take long.
All right, this is good and dry. It's been given several hours to cure. If
you try to work with the foam too early it'll become gooey and stick to everything so you're
better off letting it dry even overnight if you have the time but at least several hours
until it's very rigid but still, you know, a little pliable. Now it's time to cut it off.
You can use anything you have around the house. You could use a razor blade if you want. You could
also use a bread knife. Those work really well but I like to use a flush cutting saw. This is a
trim saw designed specifically to cut things flush. The teeth on the saw are straight in line with the
main part of the blade. They're not staggered left and right like a lot of wood saws are so
you're not going to get any damage to the surface of the door when you're using a saw like this.
The nice thing about these two is they're very bendable so you can push down into certain areas
like this and you can mimic the bevel that's going on in an area like this where we do have a depression
and because it's so flexible the teeth are designed to cut on the pull rather than on the
push so that you're not pushing and getting it to flex in an undesirable manner. So let's go ahead
and cut this off with this saw. I'll leave a link in the description for it. It's $21 on Amazon.
They work great. It's not going to take much to cut off some foam. All right now let's take a putty
knife or even better a little six in one painting tool and let's scrape away this area here so we're
nice and flush when it comes time to apply the spackling and later sand. Just gently scrape all
that off. All right next we want to get ready to add some spackling in here to cover this divot
created by the skateboard. Now if we use a spackling knife that's not quite long enough
then we're going to get an uneven application.
Something like this for drywall is a bit too long. It would work
but you might be getting stuff out here into these edges so better to go with like a medium
size one like this and that will give us a flat area here and a flat area here so that when we
come across with spackling we have the best chance to create a nice even patch parallel
with the door itself. All right I'm using a pre-mixed joint compound and I've got my little
container here and the putty knife. I've mixed it all up to get it really nice and creamy smooth
without any bubbles in it. The nice thing about having one of these is any excess on the blade
you can take right off with this metal insert that comes in these little hoppers. I'm just going to
come in here and get a fairly liberal amount of joint compound since we have a lot to make up for
and then I'm going to come across this way bring it down and just start going right across.
I don't want to go too thick because it'll just crack if I do. It's going to take a couple
coats it looks like but you can see what we're starting to do right just starting to build up
in that lower area right into this spot here see if I can push it into that spot
clean my blade. All right we're gonna let that thoroughly dry it'll probably since there's uh
it's water-based uh there it'll probably sink a little bit we'll sand the area smooth
and then we'll put on another coat. All right that's had plenty of time to dry
and as I go over it with my flat edge here of this speed square you can see in this video how
we do have a depression still in it which is just fine that means when the topping compound
dried it it sank a little bit totally to be expected better that than to have a bunch of
really big cracks you can see a tiny one here where we got pretty thick to begin with.
So let's do a very light sanding just to knock out all these high spots that's all we need there
brush that off okay and we go for another nice light coat all the way across nice
all right just clean off these spots here and here and then we'll let it dry.
So I'm starting to sand off that high spot that we created with our second coat and I am using
220 grit to start with and then I'm going to get right down to a much finer 400 grit.
The reason you don't want to use the actual block is because it's it's quite coarse
and you can easily start introducing lines into the spackling which we don't want we want it to
be just as smooth as the rest of the door. So we're going to see what we've got here vacuum
this off and then we're going to get going with some 400 grit. All right so we started off pretty
good I can see right here that we're a little bit high still from that second coat and that's just
fine. I'm going to confirm that with my speed square and yeah we've got a little ways to go
so this is a perfect time to switch over from that 220 grit paper to this 400 which will be
a lot finer and that'll keep us from introducing a lot of abrasive lines in our work. All right
it doesn't take a lot of pressure at all with this joint compound to sand it smooth so very
light pressure rather than going back and forth try more of mimicking an orbital sander which I
have plenty of but that would be way too aggressive for what we're doing here so just a nice light
sanding and kind of a circular motion does a good job. That's much better now that we got that
looking pretty good I think we're ready to put on some primer to seal off this rather porous
joint compound and get it more to the texture of the door itself. Okay we're all set up to
apply our coat of kills primer got a nice brush ready to go for that here's a tip on mixing
paint get one of these mixers it attaches right to your cordless drill right into the chuck and
makes life so easy it's a must. It's not going to take much here I'm going to get about a third of
the brush covered we're going to go light and smooth seal in that joint compound. Okay we're
going to let this dry and we'll come back and with a really fine sandpaper we'll sand out some of
these brush strokes here and then we'll be ready for the original paint that was put on this door.
So this primer is all dried and it's been very lightly sanded and we're going to use one of
these little mini rollers to roll this section of the door and we're going to roll it all in this
direction and if we do get any kind of streaking it'll just simulate the typical rails and styles
of classic door construction. So let's get a little paint on our roller here and we'll get going.
Certainly not going to take much.
So this paint is all dried and as you can see it turned out pretty good it's a very close match in
both color and texture and if you look right here and right here you may be able to see a difference
between the section that we rolled on and the original painting that was done with a professional
sprayer. Now you could mask off this area and spray it and have it even closer but if you
consider the setup time which includes filtering basically screening the paint and then also the
cleanup time which is a tremendous amount of time it's very quick for this small little section just
to tape it off and roll it and as you can see here it's a pretty close match. So now it's time to take
this door back inside and put it up on its hinges. Now it's easiest to get the door back on the
hinges if you leave it open a little bit and come at it at an angle. We've got the other pins in
this one just gets right set up in place it doesn't go down all the way. Nice mallet seats every one
of the pins and there we go. So now you know the steps to repair a hollow core door. Now the
authorities of this household like me to ask for your assistance after an exhaustive interrogation
of both children who are home at the time of the incident. A suspect was identified who goes by
the name of It Wasn't Me. The authorities don't have a height weight or age description but say
the person in question is dangerous with a skateboard and a reward of the full contents
of a piggy bank has been offered for any information leading to the capture of this suspect.
Until next time, thank you for watching.
