How to Fix a Door That Will Not Stay Closed - Moving Striker Plate

TightWadDIY
899 followers
2 Video Views·Jan 20, 2020
I’ve had a problem with one of my basement doors since I moved into my home. Its a door we very rarely use so I haven’t worried about fixing it. The strike plate was mounted too high so the door would not latch correctly. In this video, I show you how to correctly fix the issue so the door latches properly.
Use these Amazon Affiliate links to order the supplies I used in this video.
Bosch Self Centering Bit Set - https://amzn.to/36DjAcn
Chisel Set - https://amzn.to/37LAnKD
Screw Driver Set - https://amzn.to/2sNHWlj
Hammer - https://amzn.to/2RbrvYf
Razor Knife - https://amzn.to/2T7YPSm
Wood Glue - https://amzn.to/2s5YNzg
Super Glue - https://amzn.to/2T51Oeh
Golf Tees - https://amzn.to/2NarJ0l
Welcome back guys, it's the Tightwad and today we're in my basement and I wanted to show
you an issue we've had on this door since we moved in and honestly I just haven't gotten
around to fixing it because I have a deadbolt that works fine, so I'm not worried about
people being able to gain access here.
But without turning the knob, I can easily pull this door open.
So I'm going to show you today how to realign the strike plate with the door latch so that
everything works correctly and when you push the door closed, it actually stays closed.
The first thing I want to show you today is how to determine what's wrong with your strike
plate and it's pretty easy.
When you look at it, you can see the marks where the finish is rubbed away and you can
see that the latch is sliding in.
This is the center of the latch that makes this groove, so the latch is sliding in right
here and that means that the bottom portion of the latch, you can see that it's shiny
right here as well, is catching on this so it's not popping into the hole of the strike
plate like it's supposed to.
So this strike plate is simply a little bit too high, about a quarter of an inch, somewhere
between an eighth and a quarter of an inch.
So we need to get this strike plate moved down or we can try to modify it just a little
bit so that the latch will go into it as it's sitting right now.
Modifying the position of the strike plate is a little more difficult because you'll
end up with these two screw holes and you're going to have to add new screw holes very
close to these, which is a more difficult process.
Let's see if we can get it fixed first without having to move the strike plate down.
One of the most simple ways is to simply try to move the strike plate down as it sits right
now.
I don't think it's going to work on this one because the routed hole inside the strike
plate is actually flush with the metal here, but I will show you what we do just so that
you can try it on your own.
You need to take an object that's hard metal, like a screwdriver, and stick it right here
on top of your strike plate on the bottom edge.
And then you can take a hammer and being careful not to hit the wall, to mar it, or your finger,
tap, tap on the screwdriver, and that could possibly shift this strike plate down a little
bit.
If you do have a little bit of a clearance between the wood of the routed hole and the
strike plate here where the strike plate is a little proud or higher than the wood, you
can also try to loosen these screws a little bit and move that strike plate down.
So now let's try the door again and see if that worked.
But I'm not confident that it will, and we'll have to move on to a little bit more of a
dramatic step here.
So I'm going to push it closed now and pull out a little bit, and you see it comes perfectly
free again.
There's no latching at all.
If I lift up on the door a little bit, I can get it to latch, so that tells me it's not
too far off, but if I just simply push it closed, it's not latching.
So we need to move on to our next step.
The next steps for repair involve removing the strike plate, and I do recommend you use
a screwdriver for this and not a drill because you don't want to strip the softwood of the
door frame when working with these screws.
So go ahead and remove the two screws from the strike plate.
So with this strike plate, again, we needed to move down quite a bit, so this next step
that I'm going to show you now would not work for my particular case, but if you only needed
to move up a 16 or an eighth of an inch, you can take a file, a flat metal file, and
file down the bottom edge of this strike plate.
You can actually go all the way down as far as the bevel on this screw hole safely.
So you can take a good, almost an eighth of an inch off of this strike plate here.
Since mine's got to move down a little farther than that, we're going to have to move the
whole strike plate hole here down.
For this next step, I want to mark where I need to trim the door frame a bit to get
this all in place.
So I'm going to take my pencil, I'm going to mark the edges of this strike plate in
its new location, and I'm also going to mark the location of the hole.
So I'm just going to go ahead and circle the entire outside of these holes using a pencil.
I really like using these retractable lead pencils because they're a little sharper than
a traditional carpenter pencil and give a little more precise measurement.
Carpenter pencils are, with the wide lead, are really meant for home builders, not people
who are doing fine carpentry work.
Now that we have everything marked with our pencil, you see I'm going to have to chisel
out down here on the bottom so the strike plate will sit flush inside the door and not
on top of the door frame.
And you also see right here, I'm going to have to chisel out some of this routed hole
right here so that the latch will go into the hole because it was even with the bottom
of the strike plate already, so I'm going to have to chisel out a little bit of that
as well.
But the biggest problem is that our old screw holes here are overlapping with the area where
we're going to need our new screw holes.
So we're going to have to fill these old screw holes with something solid that a screw can
bite into to make new holes.
And there's a couple of different items that we can use to do this that you probably have
access to or already have in your home.
An item you can use to fill these holes that most people already have in their homes are
toothpicks.
Toothpicks are a little bit too small to put one in there and call it a fix, but two toothpicks
or maybe even three will typically do the job.
They're already tapered at the end so they'll slide into the hole easily, and with glue
they'll hold in there and they'll make a nice new surface for the new screw to grab onto.
But I have something that I think works a little bit better.
I'm a casual golfer so I have golf tees laying around.
The problem with my golf tees is that they're a little bit too wide to go into the holes
for the previous screw.
But I do like that it'll be one solid surface here for the new screw to grab onto.
So I'm actually going to drill out the hole a little bit bigger to put this tee in there
and then I can cut it flush and re-drill my holes.
So I picked a drill bit that is slightly smaller than the width of my tee, and I'm
just going to carefully drill out that hole a little bit bigger.
And now I'm going to take a hammer and I'm going to drive these golf tees into the hole.
You do need to use glue for this application.
Any type of super glue would work, but I happen to do a little bit of woodworking so I have
a wood glue here that I'm going to use.
So I'm going to put some wood glue on the tip.
And you should be fairly generous with the glue to make sure that it covers all the sides.
You can always wipe it off later.
And then I just tap those golf tees right into the holes.
And you see that one actually broke while I was hammering it in, which is fine.
I will now take a knife and score the edges of it so that they'll snap off as cleanly
as possible.
So I just have a little razor blade knife here and I'm going to wipe off some of this
glue.
But I'm going to carefully score the edge of this tee.
Now I should be able to take my hammer and knock the tee off and it should break fairly
cleanly here.
If it doesn't, it's not a huge deal.
But you can see it left a little bit of fuzzies there.
Do the same with this one and it comes off.
And now you can simply take your hammer and now you see the first part of repairing our
strike plate hole is finished.
We have a nice filled hole here with wood that a new screw can grab onto.
So we're going to let this dry while we're chiseling out the other parts that need to
be chiseled out.
While our glue is drying on our golf tees, I'm going to take a chisel and tap it in on
this bottom line just to score the wood.
When I say score the wood, what we're doing is the grain in the wood is going this way.
So if I just try to chisel down from the top, it's going to peel and splinter back down
towards the bottom.
So if I take my chisel and break those wood fibers, when the wood starts peeling back,
it's going to break off at that point.
So I can now come back into the top here and hammer down, going all the way over to the
corner.
And now this wood should just flake off and just keep working at it until you get a nice
smooth surface under there.
While I'm doing this, I can carefully try to chisel off anything sticking out proud
on the golf tees so that we know they're nice and flush.
And the next thing I needed to move down was the center hole here.
Hopefully you've already learned something and you like the style of this video.
If you do, go ahead and hit that subscribe button so you can easily find all of my other
DIY style videos.
Once you have it chiseled away, you can then test fit your strike plate and your new holes.
And I can see mine does fit pretty well, but the back of it is actually sitting out over
this.
So I'm going to score the backside here with my knife.
This is probably the easiest way just to take a little bit off.
I'm going to test fit my strike plate again here.
Oh, now it sits perfectly down in there and I think we're ready to add our new screw holes
once the wood glue dries.
So I'm going to let this wood glue dry for about 24 hours and then I'm going to come
back in and I'm going to drill new holes for my screws.
With the new hole cut for the latch, I can test that part out.
By simply closing my door without the plate on there and see that it does pop right in
and holds nice and flush.
So as long as the plate is at least at the bottom of this hole now, we know that everything's
going to close correctly.
It's been a little bit over 24 hours since I put my golf tees in here.
So the glue is nice and dry now.
So now it's time to drill the new holes where the strike plate screws will go.
So there are a couple of different ways to do this.
I did mark them already.
So I could start with a tiny pen tip, the smallest drill bit that would come in a kit
and drill a hole right in the center and then step up from there to the next size bit and
so on and so forth until I get to the right size bit for the width of screw or the size
screw that I'm going to be using.
But I've bought some new tools since my last project and they're called self centering
bits and self centering bits look like this.
You can see that there's not even a drill bit showing, but as you push it in, the drill
bit's exposed and it allows you to pre-drill holes right in the center of something due
to the bevel on the end of this bit.
So I'll demonstrate on the plate before we put it in.
So if I push this bit head into the plate, you see that it exposes the teeth or the bit
inside and that makes it drill a hole in the dead center of this.
I'm just going to hold my strike plate up here.
I'm going to push my drill into it and it automatically puts a hole right in the center.
I'm just going to do one hole at a time and I'm going to go ahead and insert my screw
here.
And again, I'm using a screwdriver to put this screw in, not a drill because I want
it snug.
Doesn't have to be super tight and I don't want to risk stripping it out.
Hopefully when you're inserting your screw, it does feel nice and tight, meaning that
the wood tee that we glued in there is doing its job.
So with that one in place, holding the strike plate where it needs to be, I can then come
back with my drill bit, auto-centering drill bit again, and drill my other hole.
And that just ensures that it goes exactly where we want it to go.
As I do with all of my videos, I'll provide links in the description and in the pinned
comment to all of the supplies that I used in this video.
And now for our moment of truth, you can see that it lines up exactly in the center, maybe
a little bit low, but definitely close enough to fit in there to give it a nice, tight fit.
I hope you found this video helpful.
If you did, give it a thumbs up.
If you like the style of this video, be sure to subscribe and turn on the notifications
bell so you'll see next time I post a DIY style video.
Click any of the videos shown on the screen right now and they'll open right up on your
device.
If you want to see more behind the scenes footage, you can follow me on Instagram at
TightwadDIY.
I hope you guys have a great day.
