In episode one, I introduce you to this 2018 Ram Promaster 2500 Work/Travel Van build and the plans I have for this build. I then take you on a drive to let you hear the baseline sound of the empty van. We then install Kilmat, Noico sound deadening, rigid foam on the floors, and finally a plywood subfloor.
Hi, I'm Mike with House on the Men. Welcome to the first video in my series where we're going to
convert this basic run-of-the-mill 2018 Ram ProMaster 2500 high roof into a hybrid work
and travel van. So let's get started. So how's this going to differ from a lot of the videos
you've probably already watched on YouTube? Like me, if you've been searching around,
most of the van conversions I see on these cargo vans have been for folks that are going to be
living full-time in the van. That's where we differ here. While I do want to do many of the
conversions that they do, this is not going to be my full-time living space. This is going to be my
daily driver back and forth to work running my handyman business. And then on the weekends when
we have travel ball and camping and other family activities, this is going to be a great resource
for that as well. Why don't we open the door, we'll head in, and I'll give you a basic overview
of what I'm thinking for this van. All right, so as you can see, this is a bare bone skeleton of
cargo van. There isn't any paneling on the doors, nothing on the sides, nothing on the ceiling.
It is completely open space. And if you look here, there's rivnuts going all the way around
the perimeter here, which tells me that it used to have a gate that separated the cargo area from
the passenger area. And in fact, I found a little piece of paper in here when I was cleaning it out
that makes me think it was originally an on-track delivery vehicle. And you can see that it's had
plenty of work. There's bare metal on the floor here, there's little waves and dents in the wheel
wells, and there's little bumps and dings where packaging items have bumped into the wall. So
that's no problem because we're going to cover that all up. So for the overview of the van,
the first thing I want is a bed right here on these about mid-height rails. Now that gives me
enough height to fit all my tools for my daily handyman business needs right underneath the bed.
So it's truly going to be a garage for all my tools. On the passenger side of the vehicle is
going to be the water tank that's going to run over to the sink and hopefully a shower. The
driver's side of the van is going to have all the electrical from the solar panels that are
going to go on the roof, the battery, the inverter, all the things that we need so that we can route
electricity throughout the vehicle. Now as we step back towards the front passenger area,
in this first space as you walk in through the door, since there's four of us, we're going to
need bench seats or bucket seats to go here for the girls to sit and strap in with seatbelts. We
can't just have them sitting out on the bed while the car's in motion. That would be unsafe. Now that
becomes a consideration and it's another difference from most of the van builds I
see where there's really only the two seats up front and everything else is living space.
We're going to actually have to come up with a way of mounting either a bench or a couple bucket
seats back here that have their own built-in seatbelts so that we're not bolting too much
stuff into the frame of the vehicle. Now as you've probably seen from most of the van builds, the
first thing we're going to need to address is what they call in the auto industry SVH, sound,
vibration, and harshness. So these vans are basically a big old can and every one of these
big panels has quite a bit of echo and resonance going on. Not so much on the ceiling where it's
corrugated or on the floor but definitely these back doors. Everything is going to have
sound deadening put into it. So I have some kill mats that's highly rated on Amazon. I'm going to
start installing those all throughout the walls, the low points in the floor, the ceiling, also
on the doors, and then we're going to put insulation in because we live in Las Vegas here and it gets
very hot or actually very cold. So we're going to put 3M Thinsulate insulation throughout all
the big accessible areas and then up front here above this headliner we're also going to put some
of that kill mat but then I also have another thinner foam insulation that I'm going to do
for the whole area including the doors and if necessary maybe even some of the floorboards
in the van. So in an effort to take you along with this journey of quieting down this loud van,
the first thing I did was set up this little Zoom H1 microphone as well as a camera up front
and I drove it around like it is right now bare bones so you can hear how much vibration is going
on. So at various speeds and various differences in the roads and going over bumps and through
construction work you can hear how this van just rattles and echoes around back here.
All right, first thing we're going to do is take a rag and some isopropyl alcohol and we're going
to clean every surface before we put the kill mat strip on. Once the strip is applied with the
adhesive backing we're going to roll it on. It has kind of a waffled pattern to it and once it's
rolled that pattern is supposed to change and that shows you that you've rolled it enough and you've
got it well seated onto the metal. For the certain pieces that we might have to trim down inevitably
I've got these really heavy duty shears that I'm hoping will do the trick and then I'm going to
wear rubber gloves the entire time since I'm going to be working with alcohol. All right let's go
step by step through the first panel and then we'll do all the rest. I'm going to start with
this back door here because it's such a nice big area I won't have to cut any of the mat or do
anything. I'm just going to put it right in the center and that way we'll get the most bang for
our buck as far as the vibration being tamped down. Now the directions in some of the other videos I
watched said to really look out for these edges because this is almost like tinfoil and it's
pretty sharp so just be careful.
All right let's do a little test so this is one we haven't done yet obviously
as opposed to
so a lot less of the resounding wave tones. Cool all right only about 100 more to go.
All right with what little bit of daylight we have I wanted to show you our progress.
You saw me started by myself but then Aspen came out to help. I was able to
tom sawyer her into helping me whitewash this fence which is fantastic.
So we've got all the walls covered. I'm just about to finish up the bottom of the actual door.
I'm not going to put any here because we're putting windows on this side
and this side which I forgot and wasted two whole pieces on but
and you can see we've got all the way down the walls. Now these two spots here
are completely filled in. That's not normally necessary. All you really need is this to
stop the resounding effect like a cymbal but the bed is going to be right here and
these are going to be the feet and behind me is going to be the head.
So on both sides I filled it in completely because I'm not going to put
Thinsulate insulation there and sacrifice that head and foot space. Instead I'm going to put a
Noiko insulation that's like 150 mil. It's very thin and that's going to go on top of this kill
mat and then we'll put carpet or something cool on the sides. It'll look nice. I'm going to finish
up the bottom of the door and both wheel wells and that'll be it for today. We still have the floor
and the ceiling to do. All right so we got the kill mat installed on the walls, on the doors,
on the wheel wells, and on the ceiling. I also want to do it on the floor but as you can see
this floor has been worn down on the high spots to bare metal and I want to put some primer down
before we start working on the kill mat in the low spots and then adding some subflooring so that we
don't have any chance of bare metal turning to rust. So I'm going to use this bullseye primer.
Now I know you might be thinking, hey why don't you use Rust-Oleum? Well Bullseye is actually made
by Rust-Oleum and it's meant for metal and it has a rust inhibitive just like Rust-Oleum. I actually
would have gotten the regular Rust-Oleum but it was locked up at the Home Depot and this wasn't so
we're going to use this. Before we do that I cleaned the entire floor so it was pretty dirty.
I put a no residue cleaner into the hot water and I took a scrub brush cleaned the whole floor off.
Then I removed all the tie down points which are really nice and handy in here. I've taken
this around on a couple jobs and those just come out with a t40 bit and then I covered each of
those holes with a little bit of painter's tape just so the paint doesn't get down into the thread.
I've got some booties that I'm going to put on my shoes so I don't accidentally get paint all
over my shoes. First thing I want to do is mix this. I've got a little drill attachment and
then we're going to get started. I think I'll give this a little time to dry and then I'll
hit the high spots again until I don't see the really dark bare metal shining through.
Well the floor is painted so now it's back to cutting sticking and rolling
kill mat. I noticed that there are these little circles going all the way along in little rows
and if you look underneath the van those are actual like framing joists that are going across
and if you tap on either side of those you still get quite a bit of ringing
like that echoes a lot but right in between them it's pretty deadened and then on the other side
right back so I think what I'm going to do is cut it in strips in such a way that
I'm only going to treat on either side of those joists so we may get a little further with what
we have left. I saved four pieces. I want to put two up above the headliner and one on either door
to also deaden all that sound in the cab area. So here we go. All right so we're over on the
passenger door and I've removed the panel and also the little bin here. Now before you freak
out and say hey I would have liked to have seen that please watch this video that I'll link up
above. It's by The Fit RV and it's literally called How to Remove the Door Panels from a Ram
ProMaster. It is so good I would be wasting YouTube's time recreating it so watch that video
on how this panel comes off. Once you get it off you'll find out if you're fans like mine that
there's a little bit of dirt all around here so that's to be expected. I'm just going to take a
wet rag and I'm going to wipe all that off first because this is a perfect opportunity to get in
especially up here by the window where food and stuff might have dropped in there and just get
all that cleaned off. You're not going to have another opportunity unless you take this whole
panel off again and I'd rather not. All right now there is a kind of a thin foam pad here
that is like sound deadening but we're going to add to that but first I want to go inside
on the actual door and put sound deadening kill mat on the door itself. So to get access to this
area we need to peel this back but luckily it's just stuck on there with this really really sticky
black goo and you can just kind of peel it off and it'll go right back on when you're done. It's
pretty cool. So let's peel this down and we'll get the top view and then when we're done with this
side I'm going to peel this side up and then get down towards the bottom half. So from here we've
got this access area here and then we'll be able to get in through the speaker hole. One thing I
recommend when it comes time to start putting the kill mat in is to put some gloves on because these
edges are a little bit sharp and if you're trying to roll and you slip you could take off the skin
right off your knuckles. So I can see that there is quite a bit of the same kind of road grime
in there and that's not too surprising since the window rolls down right here. So I'm going to get
in there first with just a wet rag and I'm going to wipe down this whole area in there that I can
actually reach. All right so right here and right here are the tracks for the window. The window
rolls right down on those. So there is a good three quarters of an inch to an inch of clearance
that we have to work with on most of the door except right here where there's a little
line indent on the door for trim sake it gets pretty close. So the reason I'm pointing that
out is to say I recommend you don't try to put the Thinsulate insulation in there because that
is so thick that it would start impeding on the window rolling down. So instead we're going to
first put some pieces of kill mat in there everywhere we can and then I have this Noiko
foam insulation and sound deadening. So we're going to also slip that in to as many places as
we can back here. I already did it on the other door and drove around and it it's such a quiet
door now it's really impressive so let's get to work on doing that. Now you can't really fit a
whole sheet in here it doesn't really quite fit in any way but I think I can get about a half sheet
right in here you can see my fingers and we can get probably a third of a sheet or so over here.
So I'm going to cut that real quick. I wouldn't take off the whole back and put it in there
because you might just get it stuck. Instead what we're going to do is start from one corner
I'm going to peel back and hold on and then I'm going to guide this in here and
not let it touch yet. You'll see why in a minute. I don't want it to stick against the door right
here it wouldn't do us much good. There we go. So now that we're in place I can peel back the rest of it.
Just first rubbing it down by hand. All right now I'm not so worried about cutting myself.
That's better. Okay so we'll repeat that over here and then we're going to come in with the
Noiko sound deadener slash foam insulation. So with this one let's see how far I can get.
Now this product by Noiko you don't have to roll you just they say to rub your hands across it
make sure it's all pressed down real good and that there's no air bubbles. All right I can fit another
small little piece right down in here. Now we look on the full sheet paper we can see the whole paper
came up so none of it tore so we know we've got a good seal there and same thing with that little
piece that I cut down there. So good to go there. All right and repeat the same thing over here and
then when we come back I will work on this bottom area. All right so we got the top done put it
right back into place here. This stuff's very sticky so you don't have to replace it it just
goes right back into place. Then I peeled up this area and I just kind of wrapped it and stuck it
against here temporarily so we've got this workspace. Yeah if you have a look in there that's
nice and smooth all the way across. Okay let's listen to that. Oh yeah that's just a dull thud now.
Okay so we just take this little bit of goo right off of there. Carefully slide this guy right back
into place. So next thing I'm going to do is take the Noiko and I'm going to cover without covering
up these holes that the pieces go back into. I'm going to cover as much of this foam padding
with some more of this Noiko as possible all the way around this and then on the other side of the
plastic panel pieces as well and that's right off of their little website their video on
on how to do it. All right I'm going to put a couple pieces on the back of the trim panels
that are going to go on here and then we'll put it all back together. All right so put another
piece right on the back here. I made sure not to be close to these little yellow tabs
because we're going to need those to click right back into place. Nice right? Now the next piece
that goes on is the top piece. So there's already a big piece of styrofoam on the back of the door
panel so all I did was add a little bit right here where your drink and stuff goes so that's a nice
area to kind of keep quiet. Well I did record the whole thing but the battery ran out. Anyway
listen to this. It's just a dead thud all the way through. It's awesome. All right so we have put
Killmat sound deadener all the way around the back of the van. We've done both doors so I think it's
time that we do a kind of a mid sound deadening test drive to see where we're at. All right
second trip, same settings on the microphone, everything. Same route as well. Let's see if
there's a difference. Bass, tone, mids are kind of gone out of the noise I heard in the back.
So what'd you think of the difference with all the sound deadening on there? Could you hear it?
I sure could from the driver's seat so I hope it translates through on the microphone. All right
next step is to start on the insulation that's going to be part of the subfloor. From
right here where we're going to start we're going to put in a layer of rigid foam insulation and
on top of that half inch plywood. Now so that we're not always walking right on the foam
insulation and crushing it we're going to also put in rows of one inch by one inch square aluminum
tubing and those are going to act as floor joists going across the raised bumps so that
we are transferring that weight from the plywood down on to the aluminum and sparing the
foam insulation all of that weight. Here's what I got. This is available right at your local
Home Depot or Lowe's. This is one inch thick polystyrene and now poly iso if you can find
to cut because this is basically styrofoam and you've got all the little styrofoam balls that
are pressed together and they're going to just flake and ball everywhere when I try to cut this
but it's what I had available at my local store so it's what I got. Comes in a four by eight sheet
and this particular brand has a kind of clear plastic on this side and then this side
is like an aluminum foil backing so that might keep it together from crumbling all over when I
try to cut it. We'll find out. So I have measured out the center line is right on top of this ridge
here and the widest point on the floor is 74 inches so we're going to start by cutting this
foam board down to 74 inches and then I'm going to go from the center line out each way as we go
and mark around as I take measurements the wheel wells and this back piece here is going to be the
most difficult because the rest of this van is pretty much a straight run so I marked out 74
inches on the tin foil side of this which makes it easier to see my marks and I'm just going to
take this t-square line it up with those marks to make sure we're nice and square I got a nice
fresh sharp blade in this box cutter so if you keep that seam close like this you can just run
your razor right on down and it cuts off that spare piece no problem right so we're basically
going to be coming in like this and we're going to need to cut around the wheel well so I'm going
to start taking measurements from my line and start plotting out and then I'll cut around those
all right working off the center line I came out and traced all the measurements
so we're coming a little pocket before the wheel well then the wheel well and we come all the way
up around that corner and we end right here at 46 inches and that's going to give me room for
a one inch piece of aluminum on either side way better than the utility knife or the bread knife
is my jigsaw this happens to be a rigid jigsaw I've had forever it's great
but look at this cut all in one piece just perfect so time to bring it over to the van
and see how we did all right here we go nice we're real tight right along both wheel wells
and listen to this that might be asking for trouble even when I do finally glue it down so
I might go back and widen these up just a little but all right first one down that wasn't bad at
all the rest of them are pretty straight I cut out the rest of the polystyrene for the entire floor
I then cut one inch square aluminum cross supports every two feet so each four foot
section of the subfloor above would eventually touch three cross supports for the garage area
in the rear third of the van I decided to go with a heavy rubber stall mat due to it being
easy to clean and a quiet cushioned surface for my tools I used half inch plywood for the front
living area so I can eventually cover it with a nice looking flooring once everything was properly
fitted I used marine adhesive to securely glue down the insulation aluminum cross bracing and
subflooring I stacked toolboxes and cinder blocks on the plywood to keep it flat on the cross braces
while the adhesive dried the stall mat is very heavy and did not need any help staying flat
well hope you enjoyed episode one and if you did will you please give it a thumbs up it really
helps the algorithms to start sharing it with more viewers like you interested in van builds
I'd also love to hear your feedback from what kind of things you want to see how much or how
little detail you'd like to see I shoot a lot of video for each of these and I try to pare it down
into a very consumable amount for you the viewer also please consider subscribing I'm working
really hard to put out good quality content this is a first in a long series of episodes for this
van build I'm also going to be continuing my tool reviews and there's a lot of those to come as well
so it's free you don't have to do anything you just log in and click subscribe or follow if
you're on rumble now at the end of each video I'm going to endeavor to give you a cost breakdown as
well as how much weight we added to the van so the kill mat was 126 35 pounds weight added the
noiko self-adhesive sound deadening was 104 adding four pounds the bullseye primer 12 adding only
about a pound of paint the stall mat was 50 and that added 100 pounds those stall mats are very
heavy one inch square aluminum I ended up using nine pieces for this particular part of the
project that was 200 and 13 pounds two sheets of half inch plywood cost me 86 and added 66 pounds
and the one inch polystyrene rigid foam insulation was 40 and added five pounds so the total was
$618 and adding 224 pounds so until next time thank you for watching
and $18 224 pounds thank you mr airline let's try that again