Hi, I'm Mike with House on the Men,
and in episode five of our ongoing
work-slash-travel-van build series
on this Ram ProMaster 2500 high roof,
we are gonna be installing 700 watts of flexible solar
with no screws and only two drill holes.
So let's get started.
♪ House on the Men ♪
Now, the method I'm using to install our solar panels
is inspired by the YouTube channel
RV with Tito DIY.
He had a flat roof RV that he installed flexible solar on
using this method here.
Ours is gonna be a little different
because it's on a van and our roof is corrugated
instead of that flat kind of rubberized roof
that you have on most RVs.
Now, I am using four 175 watt Renogy
flexible solar panels.
You might be asking,
why would you use flexible solar panels?
They are nowhere near as efficient
as the glass rigid panels,
and that is absolutely true.
To install the rigid panels,
you would have to have a lot more height involved
because there's framing and things that go on.
Whereas this method,
I am only coming off the roof
about an inch and a half or so
when it's all said and done,
which is pretty impressive.
As you may recall from the earlier videos,
I am able to currently drive this van into our garage
and work on it for changing brakes,
installing solar panels and windows
and all sorts of other things.
So if I add too much height,
even as much as four inches,
I'm gonna lose that ability
to bring the van into the garage.
And that's why everything I'm doing up on the roof
is gonna be very minimal in height.
That's the reason why I chose the flexible solar panels.
So flexible solar panels are much more efficient
if they have air circulation underneath them.
So this whole install is actually floating
on three rows of this aluminum T-track
that's going to be glued into place.
And then we're running the T-slot bolts
all the way along the three rows
to attach the solar panels.
Now, just like in Tito's videos,
I didn't want my solar panels
to be flapping in the wind at highway speeds.
So between each panel and at the front and the end,
I have vinyl lattice molding that I got from Home Depot,
and they fit perfectly into the slots
of that lattice molding.
Now, these solar panels are a little bit wider
than the outermost channels of our roof.
So you will see me using these flat corner braces
on both sides to secure the panels down.
Now, I think because these are flexible solar panels,
they have pretty minimal packaging,
but it's still adequate,
and I wanted to let you see what it looks like.
All right, and then you have these little corner pieces,
top and bottom.
Middle pieces are a little thicker, top and bottom.
And here again, top and bottom.
The smallest T-track bolts that I could find diameter-wise
were these quarter 20 thread,
and those are going to slide right into the T-track rails.
The only problem is these little grommets here
are not a quarter inch.
They're just under that.
So I'm gonna very carefully drill those out
just a little bit so that they'll fit.
And what I noticed is if you go,
if you start right with the quarter inch drill bit,
it will blow out that grommet.
So you gotta go in two steps.
It slows the process down a little, but it's worth it.
Now, you're gonna hold the little washer in place,
otherwise it'll spin
once it starts getting the friction of the drill bit.
And then I'm starting with a 15 64ths drill bit,
and first going through and reaming out that little eyelet.
And then I step up to the quarter inch bit.
And when I do that,
I have yet to have one of these eyelets pop out,
whereas two of them,
I went straight to the quarter inch bit and blew them out.
But after we do that,
now we can very easily insert the solar panel
and the vinyl sheath that's gonna go on them
with a quarter 20 bolt.
Now on the leading edge of the solar panel,
so the very front and the very back,
I'm gonna use this single piece of vinyl lattice molding.
And it's got a channel in it
that's gonna fit right in there.
We'll drill a hole through,
and the T-bolt will come through
and will be secured down with a washer.
Now in between, remember we have four solar panels.
So in between the union of the solar panels,
I'm gonna have two of these, what they call H divider.
And you can see because it looks like an H
and they're already kind of molded together.
And so I'm gonna slide those on for the center bracing
and then put another solar panel right here
and then bolt those down onto the T-track as well.
Now this stuff comes in eight foot lengths.
We need ours to be 59 and an eighth
in this Renogy panels case.
So I'm gonna cut those down with a chop saw.
All right, 59 and an eighth.
So to add a little bit of rigidity,
even though these panels are fairly rigid
and to promote airflow underneath the panels,
which has been shown to improve their efficiency a bit,
I'm going to be installing these clear plastic
polycarbonate sheets on the bottom of the solar panels.
Now I was able to buy a five pack of these
that are two foot by four foot wide on Home Depot.
And it was a better price than buying a full four
by eight sheet and then having to cut it down myself.
So that's what I went with.
We're gonna adhere them to the solar panels
with Loctite Marine adhesive.
This adhesive specifically says
that it is good with plastic and polycarbonate,
which is great.
Surface preparation, I typically use acetone
before I adhere things like I did in the windows video,
but it specifically says on here
that rubbing alcohol is very effective.
So that's what we're gonna use.
To ensure that I don't get any bleed out
from the sides or the edges,
I'm gonna lay a pretty decent bead,
but a little bit back from those edges.
All right, don't center off of those middle eyelets
because they're not actually the center.
If you measure them,
there's two different lengths from each end.
So try to center it if that's what you're gonna do
off the panel itself.
Now, interestingly, when you read the instructions
for this marine adhesive,
it says once you adhere it,
if you can separate it to allow the air to come in
and then reset it,
it actually helps it to cure better
because it allows a little bit more moisture
from the air to get in and help with the curing process.
So I wanted to share that with you.
All right, three more.
These two remaining cutouts of that stall mat
from when we did the subfloor are pretty heavy
and also soft enough that they won't hurt anything
as we add a little weight.
I think I'll put a cinder block or two down
to evenly distribute the pressure downward.
We're sitting on the Renogy box.
I wanted to say that I needed a little over one tube
of that marine adhesive to get that S-curve of caulk
through all these panels.
So make sure you got at least two of those with you
when you get started.
The cure time on the bottle says 24 hours to paint.
I imagine since it says it's fast curing
that it'll actually set up faster than that,
but we're gonna leave it here with some downward pressure
to keep all of those sandwiched together
for a while while we move on.
So I've got all four panels laid out
with the vinyl lattice molding in between them
and at the ends.
And that comes out to exactly 107 inches.
So one inch shy of nine feet.
And the pieces of T-track that I purchased
for both sides and down the middle
are exactly three feet each.
So it is just about a perfect fit.
There's just gonna be a tiny little bit of overlap
on either side.
So I'm bolting the T-track directly
to the solar panels temporarily without the lattice molding
so I can keep all the T-track perfectly square
to the solar panels.
And that also with the corner brackets
and this center two eyelets
helps me line up perfectly
where I'm going to use that marine adhesive
to glue in all this T-track.
And incidentally, nine feet of T-track,
if you start right here
and you go all the way down to the end of the tape measure,
which the shot might be a little blown out down there,
is actually ends right before that rectangular area
in the roof that is right behind the drivers
and passenger seats where people typically
put their air conditioners and rooftop.
So if I ever changed my mind
and want to mount a rooftop air conditioner,
then I'll still be free to do that.
So the next step,
now that I've got three solar panels
linked up like this all square to the T-track
is to clean out these three areas of the roof
and the bottoms of all the T-track
to get ready to adhere them to each other.
So we're up on top of the roof
and I have to say, it's really sturdy.
Let's get into it here.
I'm hoping the rest of this tube
will get us through these couple,
well, at least two of the panels.
We'll see.
Okay, I'm sweating all over my workspace.
All right, that's one.
All three sets of T-track are installed.
So I'm going to let this dry
and then I'll remove the solar panels
that were there just to temporarily keep the spacing.
And I'm going to run another bead
down the sides of the T-track
so it looks really nice like that.
And then we'll be ready to start reapplying
all four solar panels along with the vinyl lattice molding.
So with the T-track sitting in the bottom channel
of the roof line,
you can see that we're really only going to have
the three quarters of an inch of the vinyl lattice molding,
the washer and the nut as the height.
So maybe just a little bit over an inch higher
than the actual roof line.
So I noticed these quarter 20 T-bolts
are a little bit loose in this track.
Whereas if you pull them over to one side,
you can actually pull them out.
And that made me a little bit nervous.
When you tighten them, of course,
they're going to turn like that and hold in place.
But nonetheless, it made me nervous that over time
they could come loose and actually wiggle out
and we'd have a solar panel running free.
I didn't want that.
So I wanted to put a washer down on top of this bolt
so that it can better hold in that slot.
Now this is quarter 20.
So I first thought of just using
a regular quarter inch washer, but guess what?
Those are too wide and they will not fit in this slot.
So instead, what you need to use is an M7,
either lock washer or flat washer.
And those are exactly the same size,
14 millimeters as this slot.
And you can see that slides right in there.
There's still a little bit of play for making adjustments,
but it absolutely can't come out.
And then the T-bolt still can't spin.
So the only thing it does is add to the stability.
So that was my solution.
So when getting these angle brackets,
these corner braces ready to go in,
I put the T-slot bolts inside first,
then I bolted them down fairly snug.
Then I came in with an angle grinder
and cut off the pieces just like this and this,
leaving a little bit, maybe eighth to a quarter of an inch,
and then ground them down just a little bit
so they weren't jagged.
And that way, when you put over here,
when you put the vinyl molding on,
it'll give a standoff between the solar panel
and these nuts.
The vinyl rests on this bolt here,
and that keeps it from wearing away
at the bottom of the solar panel.
And then once the vinyl and solar panel,
are on this screw here,
then on top of that goes another washer
and another nylon threaded bolt on top
to hold everything down.
All right, we got three panels in
with four pieces of the vinyl molding.
And a couple things that are really important.
First of all, these brackets,
make sure you leave them really loose.
You'll have room to get underneath with a wrench
and tighten them up later,
but it's gonna be critical
to get a little bit of leeway like that.
And then as you slip the next panel
in to this dual channel slot,
you have to reach underneath the panel
and wiggle these T-bolts
to get right into the spot underneath.
So it's not pretty, it's kind of a hassle.
Last thing, you can see some of the vinyl shavings here.
Be prepared to elongate any screw holes like this
if things just aren't lining up, nothing's perfect.
All right, everything's all bolted down securely
above and below.
And the only thing left is to run down the center
with an angle grinder with a cutting wheel
and cut all those protruding bolts up above those nuts.
We're getting ready to hook up these solar panels in series.
And that means we're gonna have an end of cable
up at the front and one down towards the back.
And we need to look at a spot
to start putting those cables into the van.
Now, the standard way to do it
is you drill a hole in the van
and all over YouTube,
I see folks using these double gang boxes here
where the wires go in, you screw these nuts down,
it holds them securely,
and then you use the same marine adhesive
or any of the other types
of really good watertight adhesives to hold it down.
It's nice, it's clean, it's pretty looking.
Only problem with this one and a ProMaster van
is that this is too wide to go almost anywhere on the van,
especially on the edge here
where I'm wanting to run my wires through
because the solar panels have all the cabling
over here on the driver's side.
So as you can see in this picture,
when you put the double gang even as far over as you can,
it still hangs over around the edge
towards the driver's side.
So instead of that,
I'm gonna use these singles that I found.
And that gives me the freedom
to place them anywhere along this driver's side system
and then just make sure from the inside
that that channel up there at the roof line
where the wall meets the roof
is a good spot that you can access
and run the cabling down to the solar controller,
the charge controller.
All right, so I looked at the diameter
of this standard PV1 solar cabling
and it is roughly 9 32nds of an inch.
And I'll be darned if I didn't go to Home Depot
and find little grommets in their specialty screw drawers
that were 9 32nds of an inch.
And so when you slide those right on,
they're a nice, good fit.
That's gonna protect the cabling from wire chafing.
Wire chafing is a really serious problem
with moving vehicles
and you wanna try to avoid it as much as possible
by protecting the sheathing.
If you ever looked into the General Dynamics F-16 program,
they almost shut that whole program down
because they were losing so many aircraft and sadly pilots.
And when they figured out what was going on,
it was wire chafing.
So we're not piloting this thing in the air,
but we're still driving down the road
and we don't wanna have any issues.
The grommet will help protect from that.
Now the outer diameter of this grommet,
I measured to be around 11 32nds.
So I'm gonna start with a real small drill bit
that's a little easier to start with the initial hole
going into the roof of the van.
And then I have this step up bit
and I've marked it with a little blue Sharpie
to be right where 11 32nds is
cause the writing is really tiny.
And I'm gonna step up that hole
right to exactly 11 32nds.
Then we can pop in the grommet and feed the wiring through.
Right behind the window here on the driver's side,
there's this seam that goes all the way up the ProMaster.
And I use that to take a measurement over
and find a really good spot, right?
Have clear access to the channel up here.
And that is 12 inches over from that seam.
So from the inside channel, there's our pilot hole.
And now I'm gonna widen that hole.
So I'm gonna try something a little silly here.
Got this little cup that we use to put like seasonings
and sprinkles and stuff in for the kids.
And I put a little magnet on the bottom of it
and I'm gonna tape it up over that hole.
So when I widen it, let's see how many shavings
we can catch rather than them falling inside the van.
Well, whatever the magnet didn't catch,
the little plastic capture did.
So I cleaned all the surfaces,
including all the areas where I was gonna
put down painter's tape,
laid down the marine adhesive,
pressed down the little wire cover,
ran my finger around just like you would a beat of caulk
in the bathroom or the sink to make it up,
dressed up pretty nice.
And then ran tape across both directions
to hold it down while it dries.
So that wiring's coming down right here
by the window we installed.
And then further back is the other portion of the wiring.
Now I'm going to fish these through
and run them along this nice open channel and down,
because over here is gonna be the battery bank
and all the electrical.
But before I fish them through
where there's all this metal,
I want to cover them in this simple plastic wiring conduit.
I bought this in a 10-foot roll
at a auto parts store here in town.
But I'm gonna start by spreading it open,
getting it up close here,
taped off with electrical tape,
and then while it's outside of the channel,
I'm gonna run it all the way through,
tape it down in several spots.
And that'll be a lot easier
than trying to go through here with the wiring
and taping up this conduit.
All right, we got all the wire wrapped up
in this plastic conduit,
taped off every 18 inches, two feet or so.
And I ran this steel fish tape,
which is just really thick, rigid wire
if you've never seen it before.
It's an electrician's must-have.
I ran that all the way through this top channel.
Rather than running it around this 90-degree bend and down,
I'm just gonna do it in two stages,
first the top channel,
and then I'll come back and do the straight run down,
which is pretty simple.
I already did it with the other cable.
So we're gonna get it started right here.
Good, now I'll do the same thing coming down here.
And I'm gonna come right out over here
on the left side of the wheel well.
This is where the cage and the battery is gonna go.
Now, you may be wondering why I didn't go down this way
and just come across this channel,
which you could, it's open.
And I'm sure I'll get to a point
where I need to run some wire through here,
but I'm gonna try to avoid as much as possible
going through this channel,
because this is gonna be where the bed is,
and there's going to be rivnuts and screws
and things going in to hold down the L-track
that I'm putting here.
And I just don't wanna take a chance on any screws
and things rubbing on the wiring,
so why not go up here where nothing's gonna bother it?
Got this piece of trim back on.
It's gonna be a great channel
to run a bunch of electrical stuff eventually,
but for now, I'm putting it back on
just to keep everything looking nice and tidy.
The two cables are coming right out of this channel here,
and above this wheel well on the driver's side
is the rack where the bank of batteries
and all the electrical equipment's gonna go.
So I've just temporarily got the two cables,
the positive and negative, tied here with a zip tie
and then kept together with another one over here.
I did cover both ends of the wiring
with a couple wraps of electrical tape.
That way, there's no way they can touch anything
and short out our solar panels up there.
And I also, while I was at it,
marked the red for positive on the positive wire coming in
just so when I get ready to set everything up
and hook these up to the charge controller,
it'll save me time.
All I'll have to do is just confirm again
that that's correct, and off we'll go.
Now, we need to head back up to the roof,
and I wanna show you how I'm clamping down
all the various wire connections
along the driver's side run of the solar panels.
I bought these insulated cable clamps at Home Depot,
and every connector I have held down as close as possible
onto the T-track so that we don't have these guys
flapping in the wind.
You can see this one's right here at the corner,
holding that union together as well.
And here is the final product.
Working great, super low profile.
Now, this set of panels has actually been installed
on the van for about a year now,
so I'm able to give you some definite feedback
on what you're going to find.
First of all, the lattice molding has broken off
on several of the ends,
and I think that could be just my fault
because I went through a couple of drive-throughs
where they had the little clearance sign hanging on chains,
and what it claimed the clearance was
was not accurate for the actual sign,
and the sign bumped and drug along
the top of the solar panels
and broke several of these lattices.
I have noticed since that point
that they appear that they may have shrunk
on the ends as well.
So over time, this vinyl may constrict,
and so the one thing I would do differently
because I can easily replace these
is I'm going to slot out the vinyl a little bit more
so it has the ability to expand and contract
in changes of temperature.
Next, the only thing I've noticed up here
that has yellowed from the UV light
are the two solar cable entries.
They are still holding up well.
So is the marine adhesive, but they have discolored.
Now, the panels themselves look like they have faded
or oxidized a little from their original dark finish,
but they're holding up well.
They still have plenty of flexibility,
and they're not brittle.
So if you found this video helpful,
will you please give it a thumbs up?
It really helps the algorithms to start suggesting it
to more van enthusiasts like you.
Also, please consider subscribing.
We're only getting started on this van build,
and I also do lots of tool reviews,
and there's many more of those to come.
It's also free.
All you have to do is be signed into your account
and click Subscribe, or if you follow me on Rumble,
just click Follow.
It really helps the channel.
Now, I'm gonna leave links
for everything I used on this install.
Other than the lattice,
everything is going to be Amazon affiliate links.
So full disclosure,
if you click on them and end up making a purchase,
it won't cost you a thing,
but I do get a small reward at the end of the month.
Now let's go down and go over the costs
and the weight that we added on this build.
So at the end of every video in this series,
we are going over the cost of this particular video,
and then also the weight we added
because the Ram ProMaster payload is around 4,000 pounds,
and we're keeping a running tabulation.
So the four Renogy panels were $1,103, weighing 25 pounds.
The nine pieces of T-track were $108, weighing 18 pounds.
The T-bolts were $26, five pounds.
Miscellaneous nuts and washers, $20, five pounds.
The marine adhesive, I believe I used three tubes,
but it might've been more.
Nonetheless, those were $52, adding three pounds.
The lattice molding was $43, weighing about four pounds.
The solar cable entries up on the roof
were $12 and a negligible weight.
And finally, we had the four polycarbonate panels
underneath the solar panels that cost $105,
weighing 10 pounds.
That gives us a subtotal of $1,469 for this video
and 70 pounds added.
If we add that to episodes one through four,
we come up with the running total of $4,831,
adding 619 pounds.
In our next video, we are going to be going over this cage
that houses all my electrical,
from the three 200 amp hour batteries
to all of the circuitry and the charge controller,
everything underneath.
I'll show you the whole makeup.
I'll show you the emergency shutoffs.
We'll link up the batteries and we'll put everything
on the app and get it all running in the next video.
So until then, thank you for watching.