In this video I show you how to adjust the idle and Pilot Air Screw on your Polaris RZR 170. I also demonstrate a complete carburetor disassembly and cleaning step by step from the service manual. The RZR 170 is the child size UTV with the 169cc four stroke engine.
Views and recommendations expressed are my opinion based on hands on testing, experience, and results.
Video Chapters: 0:00 - Intro 1:15 - Removing Rear Trim 3:00 - Initial Pilot Screw Setting and Tachometer Selection 5:31 - Setting Idle and Pilot Air Screws 9:00 - Servicing & Cleaning the Carburetor 19:27 - Conclusion
Geez, what a racket. Hi, I'm Mike. Welcome to my Waffle Square, where I obsess about things and
you get to benefit from it. So, whenever I get hyper-focused onto a subject, Brooke laughs and
tells the kids, Daddy is stuck in a Waffle Square, thus the name of this channel. So,
in our last video, this Razor 170 wouldn't even start. And if that's your problem, I would suggest
you watch that one first, but we got it up and running. We diagnosed the fuel system and the
ignition system, and we even changed out the carburetor for a new, cheaper placement one.
It is now starting very easily. It'll run at an idle, but it sounds awful. So, in this video,
I want to address that carburetor. There are a couple of screws on it that we can adjust
while it's running right now and see if that fixes a problem. And then, if not, there are
internal things that we can get to, including different sized jets and all of it. So, let's get
to it. So, to access the two screws, the pilot air and the idle screw, we're going to need to reach
through here while the engine's running to make those adjustments. I tried it with this
back cover on, and it's possible, but really uncomfortable, and I couldn't see what I was
doing very well. And so, for my comfort and the purpose of having a good camera angle,
I'm going to remove this guy. He's not too tough. It's just a matter of removing six 10 millimeter
bolts. Then, there's two Phillips screws underneath, and two of those door panel
pop-out plastic plugs. So, let's get to that. Now, for these little plastic door panel plugs,
I found it's easiest to start them with a flat-head screwdriver to get the center portion
to come out. And once you get that, you can reach in here with this little panel remover tool and
get it the rest of the way out. And finally, coming straight up, right in here, there are
two Phillips screws, one on each side. All right. See, we can see straight back there,
and we'll have an area to reach right here so much better. So, according to the manual,
the pilot air screw base setting when you service and replace the carburetor should be two and a
quarter turns out. So, that means we need to gently get this guy all the way in,
which is right there, and then two and a quarter turns out. Be careful not to go too tight because
you can damage the needle. All right. Half turn, one. Half turn, two. And a quarter.
So, when it comes to adjusting the idle, the recommended RPM, according to the service manual,
is 1,700 plus or minus 100. And I want to be pretty accurate about that. I've seen some
other videos where they say just adjust it until it sounds good. I'm not qualified enough to do
that. So, there's a couple easy choices for you when it comes to small engine tachometers. One
is this engine RPM app on your phone. I tried it out, and I'm not sure how good it's working
because there's so much rattling and so much backfiring going on with this engine right now.
So, I went ahead as a backup and also purchased this little tachometer here. You can see
just how small it is. But this wire that you see wraps five times around the spark plug wire,
and that should give us a pretty accurate reading. So, the app is $9 and this little tachometer is
$12. So, let's see how they work. I got five wraps of that sensor wire wrapped around the spark plug
wire and zip tied with the supplied zip tie. So, next thing we want to do is start the engine and
let it warm up so we can adjust that carburetor. So, it's pretty obvious to me that the idle is
running real high, and therefore it looks like the little tachometer is much more accurate and
the phone app is way off. All right, now let's reposition underneath with the tachometer right
near that carburetor, and let's adjust that way down to the 1700 range where it belongs.
So, with the engine warmed up and the choke fully off, it's time to turn the idle screw,
in our case counterclockwise, to lower the RPM. All right, now let's adjust the pilot air screw.
We want to see if we can go either direction and have the engine go up. Nope. So, let's back out
and start it up again. We'll try going the other way. So, this certainly is a much better, smoother
idle. It's no longer sputtering or backfiring. Sounds pretty good. The problem is when you start
going through the range of the accelerator, you still get it, and it bogs down a little at full
throttle. So, I asked Brooke to take it out and drive it back and forth up the street, and it drove
great for her, as you can see here. Just to confirm, we're having mama take it out for a bit. I'm
expecting it to bog out. It is. So, I don't hear it backfiring or anything. When you're full on the gas,
is it like bogging down, though, like it's like it wants to die? No, no, no, not at all. It's running
more like it used to, so way more, but I'll gas it all the way up and all the way down. All right,
let me know how it feels when you got it full throttle. The only problem is if you stomp on it
from a standstill, it'll bog down and almost die, which is indicative of a lean mixture, but
no matter how much I adjusted the pilot air screw back and forth, I could never get it to a really
good spot. That leads me to believe, if you watch this fantastic video here all about small engine
carburetors, that we could be looking at an issue with the jets not being proper for what this
engine needs and also the altitude we're at here, which is only 2200 feet. So, it might be better
to see if we get improved performance by taking apart that old carburetor that we swapped out,
clean it all out, rebuild it per the specs in the manual, and see if that improves the performance.
So, let's do that next. So, here is the original carburetor that we replaced in the last video.
Before we get started disassembling all the parts, I want to get all this surface dirt off because
this thing is filthy. So, I've got a bottle of carburetor cleaner that's going to help us with
this whole project here. All right, according to the manual, the first step is to take out
the three screws holding in the float bowl. So, I'm just going to open up this little
vent here to make sure that nothing else comes out of it. We had drained it before,
but just to make sure. Good. All right, these are three Phillips screws. There's a gasket holding
this on. So, all right. You see that in there? There's a little bit of what they would call
varnish in there. See how I can make a clean spot? So, oh, and there's a lot of debris down
there. That'll be really good to get that all clean. Thankfully, this gasket still looks pretty
good. This little needle here isn't damaged, so that's cool. All right, then we want to take off
the float pin, the float, and the inlet needle. This little guy just comes right off. Let's set
him in there. This is the float pin. This is the float, and then the needle, the inlet needle,
is inside here. So, let's see how we can push out that pin. Oh, yeah. There's the little pin
right there. Boy, that looks like it's in really good shape. All right, so this little guy right
here is the pilot jet, and we want to remove that next. Okay, he doesn't look too bad. This guy right
here is the main jet, the emulsion tube, and the needle jet, and all three of those need to come
out. Let's give them their own container.
Lots of little holes on here and a bunch of grime, so it'll be nice to get that cleaned up.
All right, I can still see that little needle jet down in there, so I've got a little
shish kebab skewer. I want to see if I can push it out like this.
There. There it is. Okay, and lastly, we have the idle screw and the pilot air screw.
I'm going to remove those and clean them, too. I can hear our rooster in the background.
He doesn't know that it's like two o'clock in the afternoon.
All right, there's a special little detool that's used for these. I don't have one,
but let me see if I can just twist it out of here. That's pretty loose.
All right, that completes the disassembly process. The manual says the next thing to do is thoroughly
clean all those ports with carburetor cleaner, so I'm going to go ahead and put the straw on here
and get to it. Okay, now the body.
Well, that carb cleaner has really disintegrated these gloves, so I don't want little bits of it
getting into the carburetor as we put it back together, so let's switch them out.
So, I found this interesting. I looked really close, and if you see here, the main jet is a 132
and the pilot jet is a 38. So, I made note of that, and if this carburetor works better
when we're done putting it back together and testing it on the UTV, then it might be worth
taking apart the one that comes in the mail to see what the jet numbers are on it and if those
might correspond to your altitude or a particular model. Okay, so the manual also said to take a
little bit of low-pressure air and spray out all the little orifices, so I put some more carburetor
cleaner in there and sprayed all those out. Did the same with the little needle jets,
and I think we're ready to start putting stuff back together. So, why don't we go in reverse order
and we'll start with the idle adjustment screw and the pilot air screw. That's all the way in,
so let's go half, one, half, two, and a quarter. Next, let's put back together the
main jet, the emulsion tube, and the needle jet. Now, the needle jet,
as I looked at it, didn't have any markings on it at all, so there it goes.
And now the main jet.
Next, we'll put in the pilot jet. Now, for the float, the little inlet needle here
slid off, but as you can see, it just goes up that and in.
Then we slide the pin right through there. Now, what it says to do in the manual is to just take
the pressure off like that, and it should basically be parallel with this line right
here where the float bowl attaches to, so that looks pretty good. All right, this little plastic
piece that looks like the cone of shame you put on your dog's neck after a vet visit. Next thing,
we're ready to put the float bowl back on. I'm going to put just a little bit of lubricant on
there just because I sprayed carburetor cleaner all over it. Let's make sure it doesn't dry out
and crack. All right, same thing around this little guy. All right, time to take out the
replacement carb and put this one back in. I showed step-by-step how to do that in my last
video, so check that out if you need to. The next clip, it'll be in, and we'll try firing it up and
see if we can tune this guy in better with the idle and pilot air mixture. Well, I went through
the same process of setting the idle and then trying to adjust the pilot air screw. Again, I
didn't notice any real difference. You're supposed to get a raising or a lowering of the RPM to tell
you when you're in the sweet spot with that air mixture. I couldn't get that, so I just kept
adjusting it a little until the throttle response was the best, and that's pretty much the best I
could get out of the original carburetor, and to be honest, it's the same as I got out of the
replacement carburetor. Now watch this when you really stomp on it in neutral. It bogs out, and
that leads me to believe there is still an issue with it being lean, but nothing I seem to do really
fixes it. However, I'm gonna leave it just like this with the original freshly cleaned carburetor
on it, because other than when it's sitting here in neutral and not all that responsive, this is how
it is with the kids riding it. All right, you guys ready? Get it. There they go. All right, how'd it run?
Really good. Really, really smooth. Good. That's good to hear. You happy? Uh-huh. That's what I wanted. Thank you, baby.
And as a dad, that's really all I need to hear. Run smooth, and they're giggling and can't wait
to get it out into the dirt. Now, one quick observation that I discovered. I'm going to close
up on this so you can see what I'm talking about. So it is imperative that the notch in the throttle
valve slide be perfectly lined up with the idle screw, because if not, it can jam, and no matter
what you do trying to set that pilot screw, it'll just be on practically full throttle, and I learned
that the hard way today. So I was curious. I took off the float bowl, and I checked the two jets that
come with the carburetor I got off of Amazon. The main jet is 100 versus the 132 on the original.
The pilot jet is 35 versus 38 on the original. So for that reason alone, I think you're better off
just servicing your existing carburetor unless it's just beyond repair, because it may very
well have been serviced and jetted properly for your altitude. Now, if you found this video helpful,
you please give it a thumbs up. It really helps the YouTube algorithm to start suggesting it to
more people. Also, please consider subscribing. I've been working really hard on these videos,
and I'm hoping that they're really helpful, and there's more to come. Now, I'm going to leave a
link to the tachometer and this carburetor I got off of Amazon, since it does work, and if yours is
not functional for some mechanical reason, you can use this one and have success. Now, full disclosure,
those are Amazon affiliate links, so if you click on them and end up making a purchase, it won't
cost you a thing, but I do get a small reward at the end of the month that helps to justify the
time it takes to make these videos. Until next time, thank you for watching.