Hi, I'm Mike with House on the Mend, and in this video we're going to turn
this pallet to this saddle stand, complete with a tray at the bottom
for the cinch and other straps. So let's get started.
Well, we recently had a brand new trampoline delivered and it came with this pallet. I've
left it out in the sun and it's gotten this really pretty golden kind of color to it. Perfect. No
graying yet, so it's the perfect time to make it into a nice project. Now I'm not going to mill the
wood very much. I want it to look very rustic because Dale Brisby says, I've got this old
school saddle pad rack. Okay. If you don't have an old school wooden saddle pad rack,
then you ain't no cowboy. And my daughter Aspen is on her way to becoming a cowgirl. So the rustic
look is the look for us. Now the basis for our design is going to be these plans that I paid
for and downloaded off of Etsy. I'll leave a link for it. Now to aid us in our efforts, I purchased
the pallet buster from Vivor with my own money, and we are going to see if we can't break down
this entire pallet with just this tool. It's got these two really substantial claws on it that you
can see here, and this cross member that goes right in the wooden piece here to give equal
pressure on either side of the nails in the center. All right, I got cowgirl Aspen here,
who's going to be the recipient of this saddle stand. You ready to give it a try?
Nice, smooth, and gentle. Let's see what happens. That a girl. Now we noticed right away that if
you don't put any weight on this side, that it's going to come up like that. So
is that all your weight? Yeah. All right, let me try.
That piece is not evident. Yeah. All right, claw on either side,
and I'm just going to go real gentle because we're trying not to break this wood.
There we go. Nice. That worked good, huh? Okay, then I'll get the other side.
Let's pop that remaining nail up. Yeah. Hey, that works good. Look at that. We'll
be able to get those nails out with a claw hammer, huh? All right. Both sides? Yeah. Now,
one of the things I saw when using these with only one side on the edges here was
that it tended to break the piece. So what they suggested is we get a piece of wood in there to
distribute the weight out a little bit or the pressure a little better. So I'm going to slide
just a piece of plywood and put it right like that, and then we can load this guy
and put him dead center again. Let's see how that works. Got it.
Oh, there it goes, and it didn't break.
All right. Let's see if we can get this one. Wow. I'm actually bending it. Look at that.
It's bending. Well, this isn't as heavy duty as I thought it was. This thing's heavy, you know,
and it bends like that. Dang. There we go. There. All right. Hold that up for the camera.
There's our first piece. It works. It's not that easy. These are really spiraled nails.
There's still a nail in there. Yeah. We'll get all that out, but that's nice.
No cracks other than what was already in it. Yep. You want to try another one?
See if it doesn't lift up my entire body weight. Those spiral nails, they take some pressure to
get off. Yeah. That a girl. There. You got it. Took a bit. Put a few rocks in your pocket.
Yes. There we go. There we go. Good. Boy, that went real easy. Maybe we'll just
bend these last ones up and do something like that. Yep. I hear it. Yep. Good. Good. Excellent.
Okay. Hey, good job. Thanks, baby. And here's our yield of wood for our saddle stand,
as well as a bunch of cleanup to do, but I'll take care of that. So between the top and the
bottom deck boards are the stringers, and there's three of them in our particular pallets case,
and they are notched underneath for the forklift to come under the pallet to lift it up. So I took
two of those stringers, I cut them in half to make four feet, and then I ganged them together
in pairs and rounded the corners with my tabletop sander. I then took the third stringer and I cut
with my bandsaw this bow in the center to mimic the back of a horse right behind the withers.
And as you can see in this video, it fit perfectly into the bottom or top of Aspen's saddle.
Oh, that's gonna fit nice, huh? Love it. Sweet. Finally, we measured the length from front to
back of Aspen's saddle. It's about 22 inches, so we decided that we would want our stand to be
24 inches long. Next, I took two of the deck boards and I made them the legs, and here they are. Let's
go over the components. So here's one deck board made into a leg. Now, we measured Aspen's saddle,
and if this saddle stand is 32 inches high when it's finished, then her stirrups will be just
off the ground, which is what we want. As you can see here, I glued and screwed one foot on either
side of the deck board, so this will be the front face, and then we have an identical one for the
rear face of the saddle stand. I then took a deck board, cut it into half, and glued and clamped it
together, as you see in this picture, so that I could get ready to make this front face. I did the
exact same thing for the back face. I decided that I wanted this top rail to be notched into
the front and back legs, just like you see here. So I took the time, measured out, cut
the notch, and then I measured the slope of the saddle, and as you see here, it was about 100
degrees, so to make it easy for myself with my miter saw and my other tools, I cut these slopes
on either side of the leg, up top here, to be 90 degrees. When it came time to measure the depth of
this slot so that the top of the stand and the slope would be the right distance apart, I was
sure to take into account the half inch that was going to be added when we put the cross pieces in.
Now as I flip this around, you might be able to see this third piece on the back.
That is the cutoff from the deck board that I also notched and glued and laminated on here
for a little bit more strength when we're securing the remaining deck boards across
between the two legs. So these clamps held everything in place while the glue dried
overnight. Now we're ready to pre-drill and put some screws in. I'm going to use a ample amount
of 1 1⁄4 inch screws here. I want to countersink them a bit so that we get into this front face
without having any mechanical fasteners showing on the front face. So I used a pocket hole joinery
jig made by Craig to pre-drill for the upper cross brace. Then I did a dry fit so that I could measure
for the base of the tray at the bottom of the stand. And once that was cut and in place, with
the help of my speed square, I glued and screwed the top plate into place. And now I'm going to use
some of the original spiral nails that we pulled out of this pallet to secure the base of the tray
in place. Since those mechanical fasteners are going to be visible, I want to keep them looking
rustic. So I've pre-drilled the holes and let's get them into place.
So Aspen made this cute little horseshoe with the horse on her 3D printer. So let's attach that.
I think we'll get it right here in the center and put a few nails in it just like you would a real
horseshoe. How cute is that? And there we go. I think it turned out great. With the exception of
a few screws and some glue, the rest of it was all the reclaimed lumber and nails from the original
pallet. And look at this. It fits just perfectly in the round spot that we cut out and the slope
that I cut into these boards. I particularly love this tray down here for the cinch and other things
to rest in. And we have great clearance for these stirrups. So if you found this video helpful,
will you please give it a thumbs up? It really helps the algorithms to start suggesting it to
more viewers like you in their feeds. Also, please consider subscribing. We're working
really hard to put out good quality content. We've got a lot more videos to come as far as
tool reviews and working on our basement. And it's free. You just log in and hit follow or subscribe
depending if you're on Rumble or YouTube. And it really helps the channel. Now I'll leave a link to
the Vivor tool that we use. Just keep in mind that it bent for me on the first use, but maybe
you can compare that one to another tool. Full disclosure, that'll be an Amazon affiliate link,
so if you click on it and end up making a purchase, it won't cost you a thing. But I
do get a small reward at the end of the month. Until next time, thank you for watching.