Hi, I'm Mike with House on the Mend, and in this video we are going to be completing
our basement office cabinets. So let's get started.
Well, in our last video we built these cabinet boxes, and in this video we have a lot to do to
finish them. First of all, let's go top to bottom. At the very top, I need to run wiring for the
lights that are going to go in the display boxes up top. Speaking of the display boxes,
when I look at the back and I see the dark wood as well as this beautiful cedar here,
I find the two contrasts to be distracting. So I want to take some quarter inch plywood and
stain it to match and cover that area so it looks like a completely enclosed box of one color.
Then we need to trim out the entire two boxes. I have this wood here. It had a rough side for
some reason when I purchased it, and it was about seven eighths of an inch. So I planed it down
so that both sides are smooth to three quarters of an inch, which is your standard for trim
and for the doors that we're going to make. Speaking of the doors, once everything is
trimmed out and these pieces are cut down to be more functional for these spaces,
then we need to make the cabinet doors. We need to make frames up here, and we need to make the
drawer down at the very bottom below our electronics cabinet. So the first thing I
want to do to make the trimming out process easier is take both the cabinets and lay them
down with their faces up. It's going to be really easy to set the pieces of trim wood down, cut the
cross pieces, and get everything situated, marked for our pocket hole screws,
attached together to confirm the fit. And then we can move that whole frame in one piece
over to some saw horses, stain it, and sand it. And while the boxes are out of the way,
a good friend of mine, Eddie, pointed out after he had been down in the basement looking at the
progress I'd made that it's going to be pretty difficult to get the sheetrock ceiling up into
that area with these tall boxes. I had explained to him that I had a 90 degree drill and I could
get up there with some screws probably and get the job done, but in thinking about it more,
he's absolutely right. While the boxes are out of the way, let's go ahead put up some of the
resilient channel that has that sound deadening quality. Let's put up some one piece of sheetrock
and then I'm going to finish off the one remaining piece of trim on the wall
that I had been waiting to do while also getting that wiring in place for the lights.
All right, I have the cabinets on their backs and I am temporarily attaching these three pieces of
trim. These are called the stiles, so in trim work you have the rails and stiles,
and they're three different sizes. This one is three and a half because we're wanting a standoff
away from the wall where the outlet and the camera box are going to be. That's the reason for that
one's thickness. This one is two and a half and that's because I have two three-quarter pieces
of plywood, basically the sides of the cabinets here to disguise. This one over here is an inch
and a half, just a nice standard piece of trim coming off of the visible wall that will be
right over here. I have taken those measurements. I know exactly the measurements for each side
and now I'm also taking my speed square and I'm marking on these boards where I want the trim
to start. So for example, there's a critical spot right here where the camera box is going to be.
I need the trim just barely coming past this shelf and mostly going up this way and vice
versa here, mostly going down that way to give me the exact dimensions for that camera box to fit
there. And that's the only real critical one. Since this one is coming up this way, I'm going
to have this one match so the doors don't look odd. Once I have all the rails cut, I'm going to
flip everything over, attach them with pocket hole joinery, sand everything on the face,
stain it to match this English chestnut stain from the outside of the box, and we'll be ready
to move on to the next step.
Well, my wife found on Instagram this really unique modular storage system that can be 3D
printed. So what you're looking at here is the back of the unit, what actually gets affixed to
a wall, or in our case, the cabinets, through these little screw holes here. And these rails
you see that look like train tracks actually correspond to the backs of these little
storage cases that you also 3D print. Those rails meet up together. You slide them in place
Integral into each piece are two of these little stops that can just be pushed. And when it rolls
along on the sliding rail here, it will bump up against there and lock it into place so it doesn't
slide off one way or the other. Now it comes in three different sizes. This is the one by one,
they call it, so a single width square. The others are two, so a rectangle of two of these
boxes. And this is the big one, the three. So I printed out several of each. The twos I'm going
to use for my charging cables. Perfect for those. And the three, pull it out here. I'm going to put
my pens and things in. And then these singles, I think I'll put some batteries or screws, you know,
whatever you want. You could see this easily being used in a workshop with screws and nuts and bolts.
Really cool. And I love how it slides and can also pivot down so you can get an easy reach
on your materials. Now these rails that you see on the side here are to join them together
like you see here where they are interlocked into each other and then can be slid across the rail.
So let's build one and I'll show you how it works here. Here's a little single and it's got this
awesome little piece. All this is integral. You didn't even have to assemble these little bits
here. All 3D prints on its own. So pull this out just a bit and slide it into this little notch
here. Just like this. Trying to stay in focus for you. And there you go. Pretty sweet little system.
Let's bring it over to the cabinet and install it. So here's the spot I picked. It's just a couple
inches up off of the bottom of this particular cabinet. I've got it close to the where the door
is going to be but slid back enough so it's not an imposition when I open the door to be using
things and we are over enough that I can slide on my biggest three-piece one and then connect
the other one right here and slide them on to the end together. So I've got my level up to make sure
that we are good to go there and I'm using my switch driver by works. I just love this guy.
I'm going to pre-drill then switch over to the driver bit. Now that that's done I'm going to
push this little stop out and I'm going to start sliding the first one on. It's a pretty tough
friction fit. That's going on pretty smooth actually. Cool. Now right before it starts engaging
I want to slide on my little single just like that. Bring it all the way over
and there we go. Perfect. Well that's a lot of progress that we've made and it's already paying
dividends. I've already got some of my electronics in here charging and stored. I've got my camera
box in here to hold my various cameras and keep them dust free which in the area we live is a
great benefit. So the next thing we need to do is start making doors. We need to make a drawer
down here and then a face for it and then all the doors for the rest of the cabinets.
To make the what you call rails and styles of each door we're going to be using a very common
router bit set that has opposing bits. They are basically mirror images of each other and they
have these bearings in them that the wood rides along as it's being milled. I'll show you this
process once I get it all set up on my little router station and we'll start making doors.
So measuring all of these openings to get exact dimensions so that I can calculate for the doors
would be a perfect use case for my Recon T1 Tomahawk digital tape measure because it will
calculate its own base up through its own length and then as you raise the tape measure will give
you the exact inside dimensions. The only problem is it's got a very bad parasitic draw. It's been
like two weeks since I've touched it and the battery is completely dead. Now on the other hand
this Acigament has been sitting around for the same amount of time and it fires right up because
it doesn't have the same parasitic draw on the battery constantly. So I could just use that one
if I wanted to but the cool thing about the T1 Tomahawk is it's got this little screen that would
have shown me all the measurements that I could transfer over to my little drawing here. I'm not
paid nor sponsored by either one of these companies. I bought both of these tools with my own money but
that's just a little data point if you're considering one. With the Tomahawk unfortunately
just sitting there charging doing nothing I can turn my attention over to the Acigament by pressing
this button right here. I get the laser beam telling me what distance it's going to measure.
A click of the button and there is my final inside dimension measurement. Or by simply
pulling out the tape it switches to this mode. I have it set to calculate its own length
and it gives me the same dimension. Well after struggling a little with technology I was able to
get all the measurements that I needed for the openings of our cabinets and plotted those out
to make a cut list for the doors. I then went through and on my little router table here
routed all those pieces. As you can see in this picture here they turned out really good. There's
a slight little bit of play between the corresponding pieces but that will allow for
plenty of glue. We are ready here to start gluing up one of our panels. As you can see in this
picture in the wading wings over here are all the doors that I have with quarter inch panels that
are going to slide right into these grooves. This particular one is going to be the face of the drawer
at the bottom of the cabinet and for that reason I am using half inch plywood that as you can see
in this picture I milled down to have a quarter inch lip. That way when I make this one the
back here is going to be flush with the back of the perimeter wooden pieces and that'll make it
a lot easier to attach to the front and not get warped from putting screws in or anything like
that. Now we are going to be using just standard wood glue. This happens to be tight bond and I'm
going to put glue in just the outside couple inches of each of these stiles and then in the
corresponding area of the rails and then I'm just going to brush them. I don't want to put any glue
in the field where the panel resides because this is plywood this is actual wood. Actual wood is
much more reactive to changes in temperature and humidity and it expands and contracts accordingly
whereas plywood is much more stable so you do not need to glue your panel. Now I've said this before
in other videos but this is among my favorite parts of the whole process is gluing up panels.
For some reason I just really enjoy it. Hi Reese! So a little glue then I have just a tiny little brush
I'm just going to spread that glue around that'll give me less squeeze out and more surface area
actually covered. If we do get any squeeze out I have a wet rag right here ready to wipe that
off immediately. It's a lot easier to wipe it off now than it is to have it squeeze out and dry and
have to scrape it off and sand it more. It's an incredible pain where you can just wipe it off
while it's wet. All right I'm going to slide this piece in line it up perfect with the outside here
good and then in this case I'm going to slide the panel in first because it's such a tall
and skinny run. Sometimes I'll put both pieces in and then slide the
panel in last but I think it'd be more of a struggle here with it being this tall.
Now there are a lot of very decent clamp manufacturers out there. These happen to be
made by Jet and I really like them. I'll leave a link to these. I really like the releases and the
the kind of rubberized feet on here when they clamp the wood together. They never leave any
kind of creases or mars in the wood even with really soft wood. All right this is all lined up
I'm just going to start applying some tension just enough to squeeze all those joints together
but not bow it up like this. All right and there we go here's the front nice and flat
here's the back of the panel and it is flush because I used that half inch wood. So a couple
more wipes of any squeezed out glue we're ready to set this one aside. So check this out it just
take it over to a corner set it like that and your workspace is clear to make another panel.
So I've got what do I got five left to do today and then the top ones I'm going to wait to do
because I'm going to be putting either an acrylic or glass into those so I'm going to want to stain
those four pieces the rails and stiles for each door at the same time I stain these. And there
we go all sitting there clamps. All right these have cooked overnight so they are completely dry
and let's take a look yeah that turned out great. All right I sanded the wood on the perimeter
down to 120 because I knew I would want to come through again and do the finish sanding
down to 220 that I already did with the panel. So before I do that though I want to mark out
where our door hinge is going to go. So I have made this little jig I've made several of these
over the years it's a piece of plexiglass put into a piece of wood in this case a piece of MDF plywood
and as you can see in this picture I have set it up to go down from the top or the bottom of the
door four inches and that's where we're going to drill our hole for this little hinge here.
It's just a circular area that the hinge goes into and then you can screw it into place to hold it
and then this part here screws into the cabinet.
So I want to mark that first thing I want to do is look at the door and see which side I like
for the side that's going to have the handle which side to have the hinge. I want to make
sure there's no knots where the hinge is going to go because it's hard to drill into a knot
with a large drill bit. In this case we can go either way so I'm going to line up my jig
and I just got a an awl which is just like a little sharp point to mark it then I'll take
it out to the drill press and as you can see here I'll drill the holes and then we can come back
sand and stain these doors. It feels like I've been putting on stain and polyurethane for days
so here's the two frames that are going to have the plexiglass on them for the top display cases.
Here's all the doors and then I have a piece of trim for the toe kick
and then that one right there is going to trim out the top for just a little extra detail.
When you have trim like this that is not flush with the case that overlaps the case
you should use hinges like this. They actually go right on this edge of the trim and screw
in like this however in my case I have these hinges and I have like a dozen of them that I
bought when a store was going out of business like 25 years ago and I've been carrying them
around in this coffee can so we're going to use these but to do that I had to equal the trim
to the case with little scrap pieces like this that I have glued and stapled into place
and then I made this jig so they will line up these screw holes perfectly to the little pieces
here that get screwed into the case itself and then mount onto these hinges.
Now these hinges for the display cases on the other hand are brand new they're from Rockler
and the doors will lift up and be locked into place while I load items into it and then this
gets pushed and the door will come down and click into place. These are great I'll leave a link for
them. Well here we go a nice end to the basement office project. I thought these doors turned out
beautiful. I like the very simplistic almost shaker style detail that's on the doors themselves.
I love how my display cases turned out. I have this one full this one over here is still ready
to be filled up. The full extension drawer down here is going to be very handy for things that
I don't necessarily want to organize in the cabinets themselves. The next thing I will
probably do is make shelves for them. It's just a simple cut of plywood with a little piece of trim
on the front and so we can utilize all those shelf pins we put in on the first video. So if you found
this video helpful will you please give it a thumbs up it's really helpful to the channel.
Also please consider subscribing. I work really hard to put out good quality content very detailed
and it's very helpful to the channel. Now speaking of our videos we're going to take a break from the
basement. I have a few tool review videos that I need to finish up and upload to the channel
since it's springtime and everybody's working outside getting their yards ready and I'm excited
about those products to bring them to you. I'll leave links to the hinges and a lot of the other
things that I talked about in this video. Now full disclosure most of those will be amazon affiliate
links so if you click on them and do end up making any purchase it won't cost you a thing but I do
get a small reward at the end of the month. Until next time thank you for watching.