Hi, I'm Mike with House on the Mend,
and in this video, we are gonna transform
this useless little bottom corner
of our basement stairwell from this
to this, this, this, to this,
complete with remote-controlled lanterns
and wallpaper on the inside.
I'm gonna tell you how to do it step-by-step.
Would you please give it a thumbs-up if you like the video?
All right, let's get started.
House on the Mend.
Well, as you can probably see,
I've started some preparatory work
underneath the stairwell already,
so you can see the drywall and a little bit of insulation.
Let's hop over there,
and I'll show you what I've been doing.
Okay, we are standing underneath the stairwell
in between the framing on either side.
So you can see the stairs are sloping down this way
where our doghouse is going to reside.
This space right here is gonna be pull-out,
full-extension drawer slides
that are on order for storage, very cool.
And then this last spot here from this stud forward
is going to be a standard coat closet
with a rod going across
for all our winter clothing to be stored.
The first thing that I did was insulate the stairs.
This is what it looked like raw,
and now you can see I've got rigid foam insulation in here.
I actually wanted mineral wool,
or commonly known as rock wool insulation,
but my local Home Depot did not have it
in the 24-inch on center style used for attics.
All they had was fiberglass, I didn't want that.
So instead I got the two-inch thick rigid foam insulation,
and this is made by Artec.
One side is plastic, the other side is reflective.
The reflective side should always go
towards the living space.
Our storage area is not the living space.
The living space would be considered the stairwell
that leads into the house.
So I have the reflective side pointed that way.
Once I had the rigid foam insulation cut to size
and pushed in, it's just a friction fit,
then I took a pressure-treated lumber.
I cut two pieces, one that you can see right here,
and another one of equal length is just out of camera view.
That is establishing our pull-out storage area
and separating the three spaces.
I took a normal stud that you see right here,
and I put it right on the ground,
and I transferred the stud locations
with just a pencil and a speed square
so that when I put this one up,
it would perfectly match where the studs are gonna go
and they'll be nice and plumb.
I also took the time to notch these studs
since they're at an angle, they'd be actually wider
than three and a half inches.
So I just notched off both corners
so that when the studs come up, they will be the equal width.
I then took GRK structural screws
and I screwed these into place
on these three stair stretchers.
Once that was done, I measured
and I cut a piece of drywall.
And as you see here, I also scribed a spot
but did not cut it completely through.
And that is the bottom area.
You can see me kind of kicking it
or pushing it into place with my feet
before securing it with drywall screws.
And I thought that was a nice design
because then I won't have to go
into that kind of wide angle there
and try to put joint compound and everything.
So that is up, all screwed into place.
Now let's go back over towards
where the front of the doghouse is.
I'll show you what's next.
Well, the next thing I wanna do
is start framing out this area for the opening.
But to do that, I think it's best for me anyway
to have like a storyboard or a template.
So as you can see in this picture,
I've taken the time to draw out
what the doghouse is gonna look like
on a piece of hardy backer.
That is cement backer board.
That's going to be the substrate we attach right here
for the stonework to adhere to.
So let's head out, let's cut that out.
And that will be the basis for where we're gonna cut
and where we're going to frame out this area
for the opening.
All right, hardy backer can be cut
with regular woodworking tools,
provided they have a carbide tipped bit,
but it contains silica.
So you wanna cut it outside away from kids and animals
while using a respirator.
There we go.
Back in the basement,
I have the hardy backer temporarily screwed into place here
so it'll stay and not fall over on us
as we mark right here where the top of the arch is,
mark right here where the two openings are.
Now, three quarter inch plywood about right here
and here is gonna make up the wooden arch trim
that will be in here.
That's coming up here in a moment.
But for now, we wanna work on framing.
So we are gonna put a stud here, here, here, and here.
We're gonna cut and remove this one,
but instead of removing it right at the arch,
I wanna cut up the inch and a half width of a stud
because we wanna come across all of these studs
with this one.
So let's measure out an inch and a half
and mark our cut line.
I've dimmed the lights in the hallway
because we can do that now
so that you can see the laser line
I'm shooting across here.
This is where I want the height of these studs to be.
All right, with those marks made,
now we can cut this stud here,
remove this piece here,
measure and cut our four other studs
and the piece going across the top.
All right, before we get started nailing everything,
let's transfer those marks
where our studs are gonna go right by the opening.
All right, I'm not a math teacher,
but I do remember from Mrs. Turbeyville's class,
order of operations.
And what do I mean by that?
I mean, if we secure these two first
by nailing them in place,
we can possibly struggle getting this piece in.
So the better way to do it is to get that one in,
then slide this piece into place
and we can much easier wedge this piece
over than to try to bend this piece.
Watch this.
We're gonna want somewhere to attach the hardy backer,
the sheet rock and the roof line trim
other than these three spots.
So I took the time and I milled out these pieces
of two by four,
just like that.
They come down enough that we can screw in the hardy backer,
drywall and trim detail.
So to make room for this electrical wire,
I did take my router and I notched out
both of our little roof trim pieces here.
Let's attach those next.
Because we have this wire coming through here,
I feel more comfortable being able to control
the trajectory of some of these GRK structural screws.
So I'm gonna put one on each side here.
I'm gonna elevate sheet rock and the hardy backer
about a half inch up off of the ground
to make room for any eventual flooring.
So I wanna have a little bit more than this bit here
to screw into the hardy backer
so as not to have any tear out.
So I just took a couple little pieces of two by four
and let's create some extra space to screw into.
Awesome.
So I've been working on enclosing the doghouse
from the inside.
Maverick can't wait.
I'm gonna wait to frame in this area
until I get the flooring in
and do a little bit of detail with the screw holes
and everything because it's so much easier
to get in here now.
All right, so I installed the hardy backer
with the hardy backer screws that are specifically made
to drill through this kind of concrete cement board.
Then I started working on this arch of trim
to hide the two by four framing behind it.
So this is three quarter inch plywood
and as you can see by these lines right here,
I took my chop saw, it has a little switch on it
that you can use to control the depth of cut
and I cut all the way through the material
right down to the last layer with my chop saw
and I made this kind of accordion style into the plywood.
As you can see here, it makes it very flexible
and even though I wet it down in Maverick's kiddie pool,
it wasn't flexible enough
and the first one that was full length broke.
The second one I started making was about to break
in this spot right here.
So I cut away the straight pieces
and just worked on the arch piece.
I soaked that in the water
and then I brought it in from the little pool.
I put it in the oven for a bit to warm it up
and then brought it down here
and I clamped it in place overnight
and then the next morning I glued and screwed
and nailed it into place.
Next thing I did was started working on the arch.
So the first thing I did was I made an arch
out of medium density fiberboard
and that arch is great except the problem with MDF
is it's very hard to paint the edges.
They just soak the paint up into the sawdust and glue
and they don't create a nice smooth painted edge.
So I use that as a template.
So for the arch, I have three quarter inch primed pine
and as you can see up top,
I've cut all the angles at 22 and a half degrees.
That gives us a full 180
and it worked out that the long edge
that you see up top and on the sides
wanted to be seven inches
so that when we put on our MDF template,
we'll be able to, once the glue dries, cut,
well trace and cut all the way around
and to hold everything secure, I drilled pocket holes
and then glued and screwed all the way around both arches.
Once all that was done
and I had the kind of half octagonal shape,
I took that template, I clamped it at the very ends
and then hot glued it up at the top
just to hold it in place for my flush cutting router
to go around the actual pine wood
and the little collar you see on the top of this picture
has bearings inside that it spins freely.
That rides on the template
and cuts what turned out to be a pretty perfect little arch
and that is gonna go right like that,
which I think is really cute.
The brick is going to die into this
so I didn't do anything
but just kind of take off the sharpness of the outer edge.
I took a chamfer bit and ran around the inside edge
since the dog's gonna be coming and going.
I made a second arch just like this one for the inside
to cover the accordion look of the plywood
on the inside as well.
I then turned my attention to the roofline trim.
So I have a couple separate pieces here
that are going to make up the top of the trim.
These I joined together with pocket hole joinery.
So let's install them now.
All right, I have eye protection and hearing protection
because we're gonna be shooting nails
into several of the spots.
I am going to be using liquid nails construction adhesive
and this one right on the bottle
says that it's good for wood.
Drywall as well as cement board.
So we couldn't be in any better shape
by using this product as some adhesive.
All right, I'm gonna come back with a nail set
for any of the nails that are close to the surface
so that I can put some putty or spackle in there.
But for now, I'm just making sure they're all seated
so we can get to the next piece,
which is this one right here.
And everywhere I've pre-drilled
is where the little starburst of the natural wood
is gonna go.
So I can just use screws here
and then just a few nails on the outer edge.
So another bead of adhesive.
All right, I'm only gonna worry
about the squeeze out on the bottom.
I don't want that to dry like that,
so I'm gonna get that out of the way.
Now we can put on the caps.
Now I really like the way this is looking
with the three tiers build up.
It gives it a lot of detail.
And don't worry about the screw holes.
I strategically placed those
right where they'll be covered up
by this little starburst effect out of rough sawn pine.
Now, I just sat here with this mocked up
and I measured this out and cut it
and then joined it all together
with glue and pocket hole screws.
So I'm gonna stain this kind of a natural golden stain color
just like this color out in front of the house.
And then I'll come in and glue and nail this later.
Now let's install our arch.
And just to make sure we get a good adhesion of that glue,
since all I have is little finish nails,
I'm gonna use some clamps.
Now the cure time for the glue is 24 hours.
After that, I'm gonna fill in all the nail holes
and then I'm gonna paint everything right in place
before we start the brick work.
I'm also gonna paint right down in this area here
so that I don't have to worry about masking off the brick
since painter's tape doesn't adhere to masonry very well.
Now, I'm gonna paint this arch inside
that I had to notch right here for the stairs coming down
before I install it,
because as you can see in this picture,
I've put some really cute wallpaper inside
that my wife Brooke found at Home Depot
and we just fell in love with.
So after all the paint dried on the trim,
I taped everything off.
Disregard these clamps.
They're basically just holding the other side
of the arch on that I glued in place.
So I'm gonna leave this tape on
not only for the adhesive that goes behind the brick,
but also throughout the grouting process.
So I'm using just a standard ceramic tile adhesive.
It calls for either a square or a triangular toothed trowel,
which is what I have, a really small one
so I can try to get into tight places.
And we are ready to continue with our bricks.
So what I have here are thin bricks.
They come in two foot long lengths,
about double as wide as this,
that you can very easily cut down to the size
that you need.
This particular brand is called BrickWeb
and available on Home Depot's webpage.
So anywhere where I've needed to make specialty little cuts
or cut the bricks in half,
I've been using this awesome Ryobi handheld wet tile saw.
It works fantastic.
And then I round the edges off
with just a flapper wheel on my grinder.
So let me show you how this process goes.
It's actually pretty easy.
You just gotta kind of push hard
and get everything pressed into place.
I've marked out some spots that are gonna help me
with the sections I'm putting in.
And I've pre-cut all this up here
just so this portion of the video goes a little faster.
All right.
You wanna first press with the flat end of your trowel
your adhesive into place.
Make sure it's not too thick,
but that you have a nice even layer.
You have a 20 to 30 minute working time.
So make sure you only apply as much
as you can get your brick or tile into that area.
Now I could do the whole thing
because this will be done in that amount of timeframe,
but let's just start right here showing you this.
Now that I have it pressed into a pretty good even layer,
I wanna turn around to one end
or the other of the jagged tooth here.
And if I start right here with this one,
I think I'm gonna run into the edge.
So I'm just gonna use the little edge here
and just start creating the sawtooth edges in it.
Anything extra I can just put back in for now
into the bucket.
And I'm pressing the teeth against the hardy backer.
And that ensures that everywhere that we finished
is evenly applied.
Now this was gonna be another half piece.
I needed it to be a little longer to start on the arch here.
So I had to cut a different piece,
but let's start right here.
And I just wanna press it into place
and just move it around just a little
to make sure it seats just right and is level.
So if the piece falls off of this webbing, it's no big deal.
It can easily be cut back just with a pair of shears
or a razor knife.
So we are gonna hang these cute little lanterns
from about right here.
They run on AA batteries and have a remote.
I'm actually gonna use baling wire
to make a smaller arched little handle
because I think that would hang a little lower
than I would like.
So I'm gonna raise it up to about right there.
So I marked out where I wanted the hooks to go,
and it's just right in between these two sections of brick
here and right here.
So I pre-drilled those.
I bought these hooks.
They came looking stainless steel.
So as you can see, I just painted them
with whatever paint I had here at the house.
If you wanted to get something oil rubbed bronze,
that would probably be the best look.
All right, when it gets to these last pieces,
since you have the working time,
you can come up here,
kind of place your brick where you want it to be.
You know, you wanna have a bit of a grout line
and then draw that cut.
Now, if you want on these smaller pieces,
you can back butter them pretty easily.
All right, and I'll repeat that same process
for these last four pieces.
All right, so I have grouted half of the doghouse.
So I think that gives me a really good perspective
to start filming now to impart what knowledge
that I've gained through the process.
So first of all, I ordered this pre-colored,
pre-mixed grout in a bucket.
You can buy grout or mortar in bags,
and you can mix it with water to the consistency you want.
You can also color it.
That is, in my past experience doing cinderblock walls
and things, a lot of work.
So I naturally gravitated towards this,
but it is sanded,
and it's got more sand than any kind of grout
or mortar mix I've ever worked with,
which makes me wonder about some of these bigger joints,
because one of the things I notice
is it says it's for joints
that are 1 1⁄16 to 1⁄2 of an inch.
So there's some little tight spots
in certain areas of this wall that it's perfect for,
but these bigger areas here,
I'm curious to see how well it's gonna dry and cure.
I might end up having to seal everything
just to keep parts from falling off,
but I'll let you know.
All right, so I have a grout bag.
It looks just like something
that you would decorate cakes with,
and all you have to do,
I did not add any water to the grout,
but I did wet the bag in the beginning.
So all you have to do is load the bag.
I have a little tub of water here
that I'm using for my fingers and my tools.
I'll show you the use for it
with your fingers here in a minute,
but I recommend it.
Are you helping?
All right, I'm settling the grout
towards the bottom of the bag here,
and then you just wanna start winding the bag
just like that.
For the sake of the camera,
instead of starting down here where I started,
let's just show you how this works.
So pressure back here on this hand,
but the main squeezing is happening right here.
You can see that.
Now, the thing I noticed about this heavily sanded grout
is that it's best not to start right away
trying to form and shape it,
because a lot of it comes off on your finger.
Watch this.
So if you come right in the moment it comes out of the bag,
and you start trying to shape it with your finger,
a bunch of it comes off on your finger,
and it doesn't matter whether or not it's with your finger
or with an actual grout and mortar tool
like this one that I used for making cinder block walls.
You can even come in with this,
and it's still coming off on the tool
and not really being as effective as I would like.
So the better thing to do is to go through with the bag
and squirt into the areas.
You have a ton of work time.
Go in and out of all your lines
and then start shaping it
once it's had a little bit of time to dry.
And as you can see, as we pan here from right to left,
the difference in a freshly bagged area of grout
and an area that has been treated or tamped down,
whatever you want to call it.
All right, got my little bit of water right here.
So all we're doing is either with a grout tool like this,
if you want, there's gonna be a lot of impediments
I have noticed in this particular project,
but you could go around with your tool,
get in like that just fine.
Or since you have to put it down so often,
we can just go around here with our finger
and start tamping the area down,
smoothing out any joints in between an older bit
and a newer bit until that kind of joint disappears.
And I can feel it's more spongy now
that I've let it sit for a bit
while squirting everything in and then working up
than it is like toothpaste
where it's really clinging to my finger or my tool.
So I think that's the secret
if you're gonna use this sanded grout
in wider joints like this.
If you do get buildup, that's what the water bucket's for.
You rinse that right off.
A wet finger will bring up the cream
almost like they do when they finish concrete.
So you can do that if you're really wanting to join
an older and a newer area together.
Otherwise, if that's not working for you,
you just wipe it off with a rag and get right back to it.
If like this, there's a little too much in the joint,
just drag a finger down, get rid of that.
Hi, buddy.
You're in the camera shot.
And he's off.
All right.
And with that, the grout is all in.
While that's drying, I am gonna set my attention
to some final finishing details
like our little threshold right here.
I have a couple boards that I had to glue together.
Now we can cut them to length
and start putting on 90 degree corners to build it up.
And that'll be just about it.
Now there's a lag bolt right here
going right into the concrete.
It looks pretty structural, so I didn't want to remove it.
Instead, I just took a drill bit
and drilled out a spot for that.
And there we go.
What a transformation of this little area
underneath the stairwell that wouldn't have been any use
transformed into like an awesome,
just one-of-a-kind little spot for Maverick here
and our other two dogs.
Now there's a couple other things I still want to do,
one of which is caulking all the way around,
but I'm gonna wait to open up a tube of caulk
until I'm ready to do all the other bits of finishing
in the hallway so that it's not sitting there
and possibly drying up.
So if you found this video helpful and entertaining,
will you please give it a thumbs up?
It's really helpful to the algorithm
to start suggesting it in the feed to more viewers like you.
Also, please consider subscribing.
I'm working really hard to put out good quality content.
Our next video is going to be right next door
to the doghouse where we are going to install
full extension drawers that will lead out into the hallway
so we can store a lot of our stuff
that's currently sitting in our garage.
It's free.
All you have to do is log in and click follow or subscribe,
depending on whether or not you're watching this
on YouTube or Rumble, and it's very helpful to the channel.
I'm gonna leave links to anything that's Amazon-related.
Everything else I got right at Home Depot.
You can find all their stuff online.
Some of the specific things,
like the wallpaper and the brick, the mortar,
those kind of things, if you like this exact detail,
I'll leave in the description below.
Anything that's going to be from Amazon,
full disclosure, is an affiliate link,
meaning if you click on it and end up making any purchase,
it won't cost you a thing,
but I do get a small reward at the end of the month.
Until next time, thank you for watching.
Dude, not helpful.