Hi, I'm Mike with House on the Mend, and in this video we are going to transform this
area underneath our basement stairway from this, to this, this, to this.
Each one featuring full extension drawer slides. So let's get started.
Well, so far in this series where we are finishing our basement, we have installed this ceiling to
cover up the HVAC system that was running all the way through the hallway here. We've insulated it,
sound deadened it, and put in resilient channel and the LED lights. Then in the next video,
we made this awesome doghouse right at the bottom of the stairwell where the space wouldn't have
been that usable otherwise. And we just think that turned out fantastic. Next in the series,
we are going to be utilizing this space underneath the stairs for pullout storage.
So I am going to be using these tubs that you just get from Home Depot. These are 27 gallon.
They're about $15 each, and I will be able to, when we are done, fit 12 of these totes
right inside this area from right here to right here. Now to do that, I'm going to need to remove
this stud here and this stud here. I need to frame up the area underneath the stairs right here
because we are going to be putting like one by stock across here that we're going to attach the
full extension drawer slides that are pretty heavy duty. They hold about 400 pounds,
and we need to trim out this whole area, put in sheetrock up on the ceiling and around the back.
So we've got plenty of framing to do first, and then we'll get into actually
figuring out the height of each drawer, and we will be building those boxes. So these two
here are going to have two high and two wide drawers. So they come out 40 inches.
That'll be more than enough space for these two bins to be, and there'll be two bins on top of
them, and we'll be able to do that four bin drawer twice right here, and then back here we'll be able
to do two and two. So there'll be a bottom section like this with two, and then another section up
here we can pull out and two, and there'll be a little bit more space when we pull out this upper
one right in this area here for like a plastic bin that holds wrapping paper. That's something
that Brook really wants to keep here and keep accessible since they're such long tubes. What
are they 36 inches or long or so, those tubes of wrapping paper. So first thing I want to do
is remove this blocking. It's not structural at all, but it is going to be in the way,
and then at the same angle as the stair stretchers, we are going to cut this stud I've marked out
right there, this one here, and then we will put a full two by four across up here, screw it into
place with GRK structural screws. Same here. We are going to build this wall so that we can attach
on both sides to it the one by pine stock that's going to actually hold the pullout drawer slides,
and then I've already put some blocking right here where you can see I need a sheetrock to go
on this side, but then also on the back side, and since this area wasn't originally designed to be
finished on the inside, this kind of extra two by four here, here, and here is necessary so we can
attach the drywall. So without any further ado, here we go. Here's a look at our progress thus far.
I have framed out this center wall here with several two by fours, and I have put in sheetrock
on the back wall here. I'm going to wait to sheetrock up these interior walls until I know
where the second row of tracks is going to go. Now, down here I have three-quarter inch pine stock
that is the substrate for our full extension drawer slides. You can see how far
they're going to come into the hallway. Now, two things about these. First of all, here's a little
tip on putting in the drawer slides themselves. So here's another good example of how a laser level
can be very helpful. I'm getting ready to install these full extension drawer slides, so on both
sides of this little box here I've got two by stock with some three-quarter inch trim set on it
that I was going to rest the tracks on, but look at this. Over here it's set
perfectly, and then as you go back it drops down more than a quarter of an inch,
but then from left to right it's down an eighth of an inch and also down lower in the back.
So a laser level will get us perfectly level. And another challenge we faced was actually
my fault, and it's not level so much as it is square. So when putting down this center
piece of pressure treated two by four, my daughter, who's just about to go off to college,
came down and was all excited to help dad explosively drive some nails down with our
ram set. So I was all too happy to help her and keep her safe while having a good experience,
and I just took it for granted, shamefully, that this stud here lined up perfectly with the stud
on this wall. And when it all was said and done and I finally started measuring things out,
it was only then, too late, that I realized that it's actually off square by a half an inch.
So as you can see in these videos here on either side, front to back, I had to go in and shim out
the two center pieces so that we're parallel on both openings. All right, now we are going to head
over and build some boxes. So I took a piece of graph paper and I drew out the pieces and parts
I needed and arranged them so I could get the most efficient use of the two very expensive
sheets of three-quarter inch birch plywood. I then used my Kreg Jig Accu-Cut track to
cut down these sheets into the more usable pieces.
One three-quarter sheet of birch plywood yielded enough for the large box and the small box to go
on the bottom of both sides. The next thing I need to do is put a half inch dado all the way through
each of these four boards to receive the half inch plywood I'm going to put at the bottom.
I am using pocket hole joinery to construct this box. I have three sides already glued and screwed
into place. Now let's tip it up on its side. Let's put in the base and then screw all that together.
As you can see in this picture, the very tips of these pocket hole screws are just poking through
this three-quarter inch plywood. So with the flapper wheel attached to my grinder, I'm going to
very carefully shave those down so as not to mar the wood. Now with the last little bit of plywood
that was left when I cut down for these two boxes, I made these little stretchers here for these
taller pieces so that there's a little bit more support up top throughout the years of opening
and closing. So the screws that come with the full extension drawer slides are, as you can see in
this picture, a little bit short. So it works out that I can put these rails, these detachable rails,
right in line with the half inch plywood bottom. And if these screws ever show themselves to be
too small and not big enough to handle this load, then I can just replace them with longer,
deeper screws and get purchase inside of the actual plywood base. So I think that's a pretty
good idea. I'm going to be pre-drilling all these holes. So I have my little switch driver here made
by Worx and it has a drill on one and the Phillips on the other. This is my favorite go-to kind of
light to medium duty screwdriver drill. And without having to switch drills, I can just
go back and forth between the drill bit and the screwdriver.
Nice. Oh man, hard to complain about that. So with the bottom row in, I marked the spot where
our next board should go. Now I have a laser line so that I can come in here and make a perfectly
level next piece of trim. And now once I get the rest of these screws in, I will be able to measure
and cut for all the remaining drywall while I'm at it. All the drywall's in. We've put joint
compound on the screws and the brakes in the drywall and then painted everything. And now
the final drawers are assembled and installed and everything looks great. The next thing I want to
do is start working on the faces. So I'm going to take the half inch birch plywood. I'm going to cut
out an exact replica of these openings, leaving about a quarter inch all the way around to allow
for any shifts in movement as you're pulling out the cabinets and then also any sagging.
And then I'm going to install the bottom sides. I have measured right here and down here
so that I can make cuts square across those sheets. And I'm going to install the bottom
sheets first with initially just glue and nails. Then I'll come from behind and I'll finish by
screwing those panels in. That way I can then set up with some shims a gap that will be equal
on both and I will put the top pieces in. Once all those are in like this,
then we can start trimming everything out and getting the final look.
All four drawers are faced and painted and then I took the time with three and a quarter inch MDF
to trim out and define the space all the way up to the ceiling. So now it's time to put the trim
around the actual drawers and instead of MDF I'm going to be using half inch pine boards. I had to
plane them down actually. And I'm going to go around and let's start trimming everything out.
These drawers are going to be taking a lot more abuse opening and closing
than a normal wall so therefore I'm going to be using construction adhesive. I'm going to be using
crown staples and then backing up with three quarter inch screws from behind the panels.
And I think that'll give everything enough rigidity that we won't have stuff coming loose
or falling off. And then the drawer pulls that we'll put on last are going to be on the actual
face not on the trim so we don't have to worry about pulling trim off or anything like that with
our drawer pulls. Now between the trim on both sides I want to have a three quarter inch gap
here. I think that'll look pretty nice but instead of hoping this board is straight and holding it
in place the whole time I just took some tape and I marked out those lines so as we're bringing up
the pieces and getting them set into place we can work them off this bottom piece of four inch
baseboard and then we can also just pivot them ever so slightly so that they are in place with
that three quarter inch gap. Everywhere else such as up here is going to be a very fine gap over here
and then we're going to overlap on that side and obviously right here to try to hide as many of
these lines as we can to the eye. The enjoyable montage I went through a spackle and filled in
all the nail holes then I sanded everything by hand one of my least favorite tasks
followed by vacuuming up all the dust and then painted all of the trim and so our last step
is to install the drawer pulls. Now I went with a pull that is rounded that does not have pieces
sticking out so no clothing or vacuum cords or anything like that can get stuck on it. In fact
we picked these rounded ones that look like something would go on a file cabinet which
is fitting for this. All right I am going to use this cabinet pull jig. I'll leave a link for it
in the description below. I have it all set up and I've measured out for the center of this drawer
and we're just going to set this in place line it up with that center line and I'm going to drill
right through the holes provided. I'm actually just going to start them
and then take the tool away and finish the holes. Now in my case because I'm coming through the
half inch plywood and the three quarter inch plywood of the actual box I had to purchase
longer screws. Some of your kits when you buy hardware will come with two separate lengths of
screws but in our case I had to buy some longer ones and they were easily available right at Home
Depot. Now once I test fit everything I'll probably go back with Loctite and put a drop of Loctite on
each one of these screws. That way we never have to worry about them coming loose and
being all wobbly. Flick of the switch and now we're over to screwdriver mode.
Nice comfortable location. All right three more and there you have it another
very rewarding completed project. This is a great use of otherwise neglected space.
It looks nice clean and just I'm so happy with it. Now there's one more step that I'll do later when
I get this whole interior hallway done which is to take caulking and go around any of the edges
that the paint hasn't covered up. But I want to have enough of it done that I'm not just partially
opening a tube of caulk and possibly letting it dry out. So if you found this video helpful will
you please give it a thumbs up. It's really helpful to the channel. Also please consider
subscribing. We're doing a full series on this basement and there's a lot more other projects
to come. I am going to take a break from the basement to work on our chicken coop. As you
can see here the materials just arrived and fall is coming so I need to get that done. But the plans
for that coop came from a very famous very successful YouTuber so there's no need for me to
recreate a video on that. Once that's done a couple other things in the backyard that I might show you
then we'll get back to this series. Now I'm going to leave a link for all the various tools and items
the full extension drawer slides that I used. Full disclosure those will be an Amazon affiliate link
so if you click on it and end up making any kind of purchase it won't cost you a thing. But I do
get a small reward at the end of the month. Until next time thank you for watching. Hey not helpful.