Hi, I'm Mike with House on the Mend, and in part two of our basement office build,
we are going to be building cabinets. We're going to take this wall from this to this
to these two cabinet boxes ready for trim cabinet doors and a drawer featuring lighted display cases
up top, columns of shelf pinholes so we can fully adjust the shelves inside all of the cabinets.
I have my electronic dry cabinet for my camera gear that I can house right in it,
and we'll have a full extension drawer on the bottom. So let's get started.
Well, I am so excited to have a place for my electronics gear, my camera gear to all be housed
in a dust-free environment. Look at my poor nightstand right now with everything on it
collecting dust and cables and wires everywhere. It's going to be perfect to get it all housed
right in this area of the cabinetry, and that's why I put in these outlets here on our first video
in my office series. Well, you have the benefit of being quite a bit into the future and seeing
what the end product looks like, but I think it'll be fun to see what I'm hoping for in the beginning
and then whether or not we made it. So I have a ruggered dry box camera case that you see here
in this picture. It was a gift for Father's Day or my birthday a couple years ago. I really want
to prominently display that right below this area, and its dimensions, as you see in this picture,
are going to be the reasoning for this first cabinet base because I want it to enclose that
and look really sharp. That's going to give us from what about right here or so over for the
other set of cabinets, which is why they are off in their size. Now, keeping in mind this outlet
right here and the camera mount for my light box, as you see in this picture, I believe that 20
inches for the actual case, leaving what about an inch or two for trim and doors will be perfect.
It won't obstruct this outlet in any way. We're going to come off with a piece of trim several
inches off of this wall so when the door opens it doesn't impede the outlet. Below my camera box
is going to be a single pullout drawer. I'm hoping for cabinets below, cabinets above,
this shelf right here, and then up at the very top I have some military memorabilia, both from
the Gulf War that I was in back in the 90s and some World War II era military memorabilia that
I would like to be prominently displayed. Right now it's enclosed and protected in a bin out in
the garage and I just don't think I deserve to have such nice things if I'm not going to display
them. So I'm hoping to take the last foot up here and make some lighted display cases. As you see
in this picture here, that will be going along with our family room area that has the same thing,
so I think it will match perfectly. Now with all those various aspects of the cabinetry in mind,
I thought it would be helpful to make a storyboard. This is a really nice piece of
trim that's going to be somewhere on the face or the doors of the cabinets. So I turned it around
to the side that no one will see and I made markings for where our permanent shelves are
going to be because I want to route in dados and up at the top a rabbet to hold in and make
more sturdy the half inch shelves that are going to be permanent. In this area here we will have
holes drilled in for floating shelves. A good storyboard is very helpful so that you're not
relying solely upon your tape measure when you're laying out to cut in with the router because I've
made those mistakes in the past. Now for this project I am using cabinet grade birch plywood.
This face I picked out to be the face on this side, the outside of the cabinet. You won't see
any of the rest because they're going to terminate against that wall. So I wanted the prettiest look
because I'm going to be color matching this cabinet to our cabinets up top on the first
floor and I've already made a sample piece and I love that color. It's a good close match.
So with that storyboard you can see here I have laid out all the corresponding dados and the one
rabbet up top on all four pieces of plywood that are going to make up our two cabinets. Now if you
watched the first video in the office series I had originally planned on keeping this connection
with the two walls exposed but a lot of the boards when they dried, dried significantly and shrank so
I think it looks a lot better with this piece of trim on both sides of it. So I've already
installed that and that is going to be the perfect offset for the start of our cabinets right here.
So the next thing I need to do is get the measurement to where the second cabinet will
terminate and that's not going to be just based on the width of the camera box. It also I have
to take into account the width of the trim on both sides. Once I get that I'll know the dimensions of
this box which are the most critical and then we'll have the dimensions over for the other cabinet and
we can start cutting cross pieces in the back that we're going to attach with pocket hole joinery
to the cabinets themselves to make it nice and sturdy and then as I mentioned in the first video
I don't want to put a plywood back on the entire cabinet because when I open the doors I want to
see all this hard work I did but we need to attach the cabinets to the wall and so that's what those
stretchers are going to be and it just so happens since I cut two pieces at 20 inches on the plywood
and I was able to cut them at the Home Depot where they have a nice plywood cutting sled there to get
really good clean cuts and that left roughly a little less than eight inch piece that I'm going
to be able to cut down and make the areas that come across that I can screw into the wall to
really secure the cabinet. All right I have cut those pieces that we were just discussing and then
I cut them in half and the back side that you will never see I have put pocket hole joinery in to
secure them to the sides and also to screw up into the shelves. These are waiting here on my little
board to be sanded along with everything else I have laid out. Now speaking of the shelves
I have also made all of the shelves including the top of the cabinet and on this one I drill the
hole through it because we're going to be putting the same lights that you see here on these floating
shelves from our last video. I think that's going to be a really nice way to illuminate inside of
those display boxes. Those are also pocket holes all the way around so that we can secure them
into the two halves of each cabinet. Speaking of those as you can see in this picture I drilled
holes for shelf pins and I used the Kreg shelf pin jig which works very well. Now if you don't
want to pay money for a jig like that I'll leave it a link for it in the description if you want to
check it out. You can also just buy a piece of pegboard. Pegboard is like MDF medium density
fiberboard kind of plywood that you can buy that has all these holes in it. You can pop little
holders in for your tools and things very common in workshops. The thing I like about using the
pegboard is for a very inexpensive price you can make a big long sheet of it. You simply have to
line it up where you want it clamp it down and then with a centering drill bit that has a sleeve
that the drill bit pops in and out of you can start making your run of shelf pin holes.
This is a little bit more complex where you have to line things up clamp things down
and the holes wear away rather quickly so you're going to have to replace this every so often.
Whereas the Kreg hole jig as you see again in this same picture the holes are sleeved inside
of them with metal and they perfectly correspond to the drill bit that you can pre-position for
just the right depth of the drill hole and it's got a little piece on the side that helps to hold
it right against the side of the cabinet and then it has a little pin that'll hold it in the first
hole you make and so you can just repeat that process all the way up to get the full run of
your holes. Pretty cool. So the next thing I want to do is sand everything that's why it's all laid
out here. I'm going to do the other two pieces of the cabinet at the same time because once I
have everything sanded I want to pre-stain the outside of this piece here which is going to be
the face that you see when you walk up to the office. While I'm pre-staining that I also want
to stain each area up where the display box is going to be including the top and bottoms
of this display case and one of these cross pieces that is going to be at the very top
that we will use to secure into the wall. So that's all done. I used English chestnut as the
color of stain for the outside of the cabinet as well as this area you're looking at right here
which is going to be that display case. Prior to putting on the stain I did use pre-stain wood
conditioner. That a little bit goes a long way. I was able to use this tiny little can here
and when you put that on first and leave it for 30 minutes it makes the color across as you can
see here really smooth no blotchy streaky areas that you can get from wood that is just completely
untreated. So that really did turn out nice especially on the outside of the cabinet that
looks so pretty. Now for the areas where I'm not staining I did use a sanding sealer as usual to
bring out the grain. Sadly the polyurethane I am really enjoying this matte finish crystal clear
is water-based and it specifically says not to use my all-time favorite deft lacquer sanding
sealer because it's oil-based. So I had to go instead with my least favorite which is a water-based
sanding sealer. I've had trouble in the past with them bubbling up on the foam brush and leaving
kind of a nasty residual but that did not happen with this it worked just fine. So next thing I'm
going to do is every other surface including the stained surface is going to get a polyurethane
coating. Well the time has finally come for my favorite part of any build the assembly. So I have
some wood glue this happens to be made by Titebond and then I am attaching the shelves to the cabinet
sides with pocket hole joinery. So in this case I am going to be trying out these three quarter inch
much shorter screws than I've been using in the past. If you watched the video where I made the
pullout drawers every one of those screws protruded through the side of the cabinetry and I had to cut
them off and sand them down with a grinder. So I'm going to try these and see if we can avoid that
altogether and still make strong furniture. Now this little guy right here at first glance might
look like a stealth bomber but in actuality it is a clamp that I made at home out of plywood.
I just notched this corner off so it doesn't get in the way but I'll set it down like this,
clamp it here, put the shelf on, clamp it to the shelf and that makes sure this shelf will be
perfectly square.
All right one down now I can come over here make sure that this cabinet is braced
against the trim on the wall over there and take my final measurements for the second cabinet right
here where I'm standing. Then we're just going to go through the same process of the shelves and
staining and sanding and putting it all together. So as you can see here the concrete floor isn't
quite level it is low on this side and if we look over here when I installed this piece of trim
it was perfectly plumb but we're off a bit there but even if I just push the cabinet over
we're still off on the shelves so I want my shelves to be level not just the outside cabinet
so all I have to do is come down here and I will shim this side up to make this cabinet level.
And here we go both of the cabinet boxes are in place. My measurements worked out that from this
edge of the wood over to the wall is exactly three inches. My trim boards are three and a half so
that'll give us a nice bit of half inch of trim coming over the box which will be perfect when
it comes time to put the cabinet doors on. So in our next video we are going to be completing these
cabinets by building out all the trim. We are going to join the trim to itself as well as to the
cabinets with pocket hole screws. We're going to install the two lights up top and wire those in
build the full extension drawer down here at the bottom underneath the dry cabinet and I've got a
great idea for 3d printing some little storage boxes here that are going to be kind of color
matched to the wood of these cabinets and those are going to house our cords and pens and etc.
So if you found this video helpful will you please give it a thumbs up it's really helpful
to the channel. Also please consider subscribing. I work really hard to put out good quality videos
there's plenty more to come and it's very helpful to the channel. It's also free all you do is log
into your YouTube or Rumble account click follow or subscribe. It's really really helpful beyond
your understanding most likely and I appreciate everyone who has done that. So I'm going to leave
links for this cabinet as well as some of the tools and joinery that I used in this video. Full
disclosure those will be Amazon affiliate links so if you click on them and make any purchase it
won't cost you a thing but I do get a small reward at the end of the month. Until next time thank you
for watching.