Hi, I'm Mike with House on the Mend and in this video in our ongoing series where we are finishing
out our basement, we are going to be turning this space way in the back corner of the basement from
this to this, this to this. Fully functional office space made out of cedar fence posts.
We have several floating shelves complete with fully dimmable accent lighting.
I put in a french cleat system to store tools and remotes. We have a wi-fi controlled space heater
that's going to go right underneath my desk and over here on these floating shelves which are
right next to what will be the family room movie room down here. We have our movie memorabilia
lego sets that the kids have put together being accented and a hidden drawer for phone cords
and remotes. So let's get started.
So I chose to finish this area back here first instead of bathrooms bedrooms or the family room
so that I could get used to some of the typical challenges that you have when finishing a
basement. Like here we have an outside corner, we have an inside corner here, we have a window well
that we're going to need to frame and then trim out. And I wanted to do all of that and get that
experience in this house with the way this ceiling height and everything functions before I move on
to all the bedrooms. Now the first thing I want to draw your attention to before we could get into
the insulating and framing part is even though this window is kind of blowing out the wall,
if you see all these little speckled light colored dots let me explain those.
Well some of these pins that hold the forms where the concrete is poured into
look as though they have leaked in the past. I haven't noticed anything since we've lived here
but nonetheless I am going to take a wire brush clean all these areas and then I have some
concrete patch or sealant that I'm going to put in with the caulking gun and hopefully
seal up these holes for the future. Much better. Once that was addressed I turned my attention over
to the window well. So as you look at this window frame you may think that this is the issue here
where the concrete is coming over the frame but actually I'm not concerned about that because
it's flush with the wall. What I am concerned about is where our trim pieces are going to go
right to this spot here and if you come and look down here in the bottom corner there's
a bunch of concrete that all has to be chipped away and then as we come across over here
there's more and look at this up top there's just this long ooze of concrete that spilled
through this gap here. So before we start putting down our pressure treated lumber and putting on
our insulation we should take care of all this because it's just going to create a mess down
here when we chip it away. Now that all that's cleaned up we can really get started on the project.
So the first thing I want to do is not put up 2x4 stud walls right against the concrete. I want to
create what's called a thermal break or a thermal barrier with inch and a half of rigid foam
insulation. If you put your 2x4s right against the concrete wall, number one the wall is not necessarily
square but number two it's going to transfer that cold right through the wood to your wall and thus
more of it goes into your living space. Instead I'm going to be using this Artec rigid foam
insulation. It has a foil side that is going to go this way so that the foil is on the living
space side. Instead of putting it directly down onto the concrete however I'm going to take an
extra probably unnecessary step which is to use 2x6 pressure treated lumber first
then set my inch and a half rigid foam insulation and put up my 2x4 walls. The reason I'm
doing that is if you research the polystyrene foam, yes it is hydrophobic as you can see here but
there is a risk of it when it's immersed in water for it to wick that moisture up into the little
air in between the little balls which is what gives it its thermal property and it can break
down that thermal property plus that water may last there a lot longer and there's really no
treatment in the polystyrene to prevent the mold. So pressure treated lumber on the other hand
is designed for that very thing. So let me know in the comments if you think I'm crazy but I'm
doing it on this section of our basement. I'm going to see if I like the process and if I do
then we'll continue on throughout the rest of the house. So let's set this aside. I'm going to get
all the rest of the pressure treated lumber and I want to start coming along this wall on the
ground then make this 90 then this 90 and the same over here. I want to get that all screwed into
itself like this so that I'm reasonably sure that I have good 90 degree corners which will make
everything come into play easier later and then I'm going to secure the two by sixes
into the ground with my ram set and then we'll start putting in the rigid foam.
So I've got my Dovo laser level set up with both vertical lines making a perfect 90 degree angle
for us in this instance and I've got them lined up pretty good on that side and pretty good on
that side. So we know the boards are square thanks to the pocket hole joinery and the laser level but
look at this concrete. Look at that big dip right there and then right here at the corner. If you
look over on this side it's going pretty good and then once again at the corner it starts creeping
in so I'm glad I'm using this method here and not just going by the wall. So I shoot the nails in
the corners or the edges like you see here for stability but then I go through and I mark where
all the studs are going to go like for example right here is where the window studs are going
to go and after all the studs are marked out then I shoot the field nails so that I never have a
situation where I have a stud going on top of a nail which is just a hassle. Now that all the
pressure treated lumber is secured and all the markings are done for where the studs are going
to go we can finally start making this space look different like we're making some progress.
I've got one sheet of rigid foam here the next one comes out about 11 inches too long so I have
marked that with a sharpie so you can see it better and I'm just going to run my razor right along
and this stuff's really easy to work with you can set it right here against
the edge. Now instead of drilling into the concrete and using anchors I am instead using
foam board adhesive. You got to make sure like you see in this picture that it says foam board
otherwise it can eat the stuff away it's I've seen it happen before it's it's not pretty it just
disappears like it's water soluble or something but anyway this foam board insulation works
pretty good it doesn't like really grab a hold but I just want to keep it in place and then
we're going to be putting up our studs any way that will hold it from anything happening plus
we'll tape it all together so according to Artex website as you see here you can space your glue
out two feet now it might be helpful to keep this stuff warm instead of storing it in the
basement like this tube was because it is coming out thick and not really sticking to the actual
plastic look at that it's only 60 degrees down here all right new tube that has been kept upstairs
it's also plastic instead of that cardboard hopefully it won't blow out let's see
all right we're going to keep going around when I get to the window I'll show you
really quickly how I cut those out and we're just going to continue on
as you can see right here I set up my laser level right here at the edge so that we can
take our next piece and mark it then I'm just going to mark the windows
that looks good let's glue it up this edge on top of the window here is drooping a bit
see that so I'm just going to set this piece in here for now so Sika makes this seam tape
for this very application it is super sticky so I'm keeping my finger on the leading edge
because if it slaps itself back on here it's you're it's really hard to get going again
we've got all the rigid foam insulation in so now it's time to talk top plates and studs so
here is a tip about top plates if you line up the top plate right next to your bottom
pressure treated lumber here and transfer those stud markings then you can come right up here
with it and screw it into place and you don't have to worry so much about using a level or
laser to get everything plumb once I have them pre-marked I shot a laser plumb line so that from
the bottom to the top was all in the same plane I took my pencil made marks and then I screwed in
the top plates to those lines now you could also build your top plate and your
boards down on the ground fasten those and push it into position however I have found
that from here to over here is a different measurement than it is from over here
so instead of chasing all these different board measurements I'm just going to go individually
and confirm the distance or the length of the stud and the tool I like to use for that
is a tape measure that has a laser distance finder on it now this particular one here is
is very similar to the recon t1 tomahawk but it has the advantage of having the laser distance
finder so oh and it also has a much better battery life than the tomahawk the tomahawk
has a parasitic draw in it and if you don't use it for a few days it's dead you have to go charge it
this one I can leave in its case for months and when I pull it out it still has battery life
you can also get much smaller much less expensive ones like this milasy the only problem with this
one is it takes the final distance of your laser shot from the front which means you have to add
82 millimeters or three three and a quarter inches to it so I don't feel like doing that one
when I can just use this one tool right here that gives me a really easy to read measurement
so with the push of this button right here it turns on the laser beam you simply put it
into position look up here to make sure you're right on that stud and right there is a very
easy to read measurement that it looks exactly like a tape measure I love this guy so after I
do that then I come back here confirm my measurement as you can see it's just perfect
where I can put it into position by hand if it was a little bit long and I could tap it into place
I'd be okay with that too now a word about construction adhesive there is nothing wrong
if you have construction adhesive to put a little dab of that especially down on the bottom a little
bit up top and when it dries it's going to help from anything shifting this way or any way of
course all right got hearing protection in because this nailer is pretty loud and with the help of
this little block here I can easily toenail this board right into place and there we go continue
that on down the road until we get all the studs in now if you pre-drill for accuracy screws
especially these structural grks are excellent for toenailing in your studs especially in
circumstances where there's just nothing to keep them from floating as you're trying to shoot a
nail in hard to complain about that so all the framing's in let's go over some of the details
now you may notice in certain spots there is not necessarily a 16 inch on center normally I would
do it that way because it makes everything easier with sheetrock but in this case I am using the
cedar boards and they are six feet high when you cut off for the little
angled peak at the top they are 71 inches so taking that into account I've measured off some
of the studs and kicked them over just a little bit so that we can butt up the two pieces together
in other things the window framing went really good I used a laser level for every aspect of
it so that I was getting the perfect measurements so our eventual trim will go right to the spot on
this tiered window that window well that I want to use I didn't use blocking throughout the entire
thing this is not load bearing this is strictly just enclosing the wall but in certain areas I
did use blocking such as in this instance here and over there where one of the boards was warped
a little bit this one was warping in and I want this wall to be perfectly in line when I go to
put the boards up so I did use a piece of blocking here to push this board out so it is on a level
plane or a plumb plane with this wall in the case of this piece of blocking right here I am
pre-positioning a good mounting surface for this little camera arm it's going to mount about right
here it's extendable and fully adjustable and my light box is going to sit on my desk desk right
here so that I can come over the top through the top of the light box and review tools and things
as I've done in the past that is also what this outlet is for here to allow me to charge things
that are sitting on the desk and but then also to power that light box easily without having to
climb under the desk now in addition to that one I've started running outlet boxes throughout the
walls in a general living space code is pretty lax about where how many outlets you need we laugh
at one per wall kind of a thing here so I have put plenty in and thus I'm gonna make this its
own circuit I don't anticipate running any power tools or anything mostly just going to be charging
five five volt electronic devices but we're going to be running a vacuum to clean up and there might
be other instances that right over here we're going to have a the space heater to keep me warm
in the winter months and because of the space heater and the possibility of plugging in devices
such as vacuums and things I am running a standard 12 gauge Romex here instead of the 14 that is
commonly used for led lighting and things like that that is coming from the sub panel I installed
right down this wall here along the HVAC system which is a perfect spot for it because we're going
to be building out a soffit to hide that and it comes right down to here and I'll branch off for
one single outlet I have over against this wall and then along this run so under the desk power
space heater light box and other devices on this wall that you can't quite see here's a picture of
it I have two double gang boxes and that's because I'm going to enclose this space eventually
with cabinetry and I want to be able to charge things like drones and other electronic devices
and have it clean not always sitting on top of my desk when being charged if you come around to this
side you'll start to see I have put studs here these are going to be for the shelves that you
saw in the opening I am making invisible shelves thinking ahead of time and installing
these studs I've put three screws in plus construction adhesive to hold them in place
they're not going to be carrying a lot of load but enough that I want I don't want them to sag
over time so you'll see I have three shelves here this shelf comes out a little further we're
putting an outlet here so when folks come over for movie night or if they're spending the night
down here anything like that they can charge devices and things would be we thought it would
be cool to have an outlet here we can also run a popcorn maker whatever by having a conveniently
located outlet here just off camera over this way is the end of the wall and we have a pinball
machine that we're going to park right there so I have an outlet box to run that continuing on
over to this wall I have that shelving here and I have staggered it by one of the studs so that
we can get that kind of cool offset look that I like on this wall here as you can see we have
kind of a repeat with just the three inline shelves that's going to be
the entrance to my daughter's bedroom someday and she has lots of trophies and trinkets and
lego things that she's put together that she wants to display here and we have one outlet box over
there just because it's a wall and we might want to run a vacuum or whatever so the next thing I'm
going to do is continue running the wiring once I get all of the wiring laid out into each of the
boxes and the wiring for the under shelving lights then I can start putting in the insulation now
word about the lighting I'm going to be using I'm standing off to the side here so you can see it
and it's not obscured by my shirt I found these lights on Amazon I'll leave a link to them they
are led they are dimmable they also tilt as you can see here so you can install them in such a way
as you point them down towards artistry if you're putting them into the ceiling which we're going to
have a couple of those for the top shelves or just straight down for shelving in this
area here the thing I liked about these was they had the black finish which goes along with the
that are going to be visible and they have their own little box that they come with
for running power to them it's nice and small it can fit through the same hole if you ever have to
replace the box and they have this quick connect here so you can pre-wire the box
anywhere along the area and have enough cord that you can reach into the opening after the
fact when you've stained or when it's time to do the final installation make that connection
and then push this light up into place another thing I thought was cool when I opened up the
box a little bit of rattling you're hearing is they actually come with their own push
lock wiring connectors instead of twist connectors I thought that was a nice bonus as well there is
a switch on the side of them where you can pick the temperature of the lighting so if you want
warm lighting that kind of more yellowy orangey lighting you can go down to that setting or the
higher the number in the kelvin range the wider the light is all my girls my wife and my daughters
like that white light and we are going to be setting those that way and then we can just dim
them down to make more of an ambiance look when we watch movies in the movie room or family room
which is right next to this wall all the rock wool insulation is specifically this isn't the
brand rock wool this is mineral wool but it's the same thing made out of basalt lava rock
and I can hear my voice deadened into the insulation it's kind of like recording in
your closet with clothes the way it just kind of muffles any echo at all it's pretty cool
some handy things I like to have when working with this mineral wool type of insulation that
kind of holds itself in place is a board the same thickness as your bottom plate in our case
we're working with pressure treated lumber since we're down here in the basement I like to take
the insulation set it on there to give it the same distance off the ground so that I can cut around
electrical boxes as well as in this case these shelves and then the best knife I have found for
cutting rock wool insulation is a common household bread knife so there's something
about the teeth that doesn't rip away at the material and the length of the blade
cuts all the way through the material rather than working with a box cutter fantastic and
some must-haves in my opinion are a long sleeve shirt and then a respirator or particulate mask
and I like to use gloves as well these are the rubber palm side gloves and then the fabric on
the other side those are really comfortable for working in here you're like your entire
hand isn't getting sweaty but you can still grip the material really well
rock wool or mineral wool insulation is a lot better in my opinion to work with
than fiberglass but I do notice that my exposed skin gets itchy and I found myself coughing if I
didn't wear a respirator so I gear up the same way as if I was working with a fiberglass all right
the next thing we are getting ready to do is start putting in our cedar boards so as you can
see in this close-up they are rough sawn on both sides but I run it through my planer and we get
as you see me spin it around this beautiful look that is going to look great on our walls there's
a nice amount of red color in some of these boards so I'm excited to get going I have the laser level
set up on the little stand that it came with so that I can set everything up a half inch off the
ground so this side is just fine this side over here needs to come up right to there we're going
to make this first row as critical to be just right and just like that through the magic of video
editing we have this first set of walls finished and I decided to stagger the way the pieces come
together rather than mitering them which it just inevitably opens and doesn't line up I decided just
a butt joint but I went end grain face end grain face and vice versa here and I like that if for
any reason I don't want to stick with that I can always run pieces of trim up like this all the way
up and down and disguise that area but for now I want to keep it like that I think it looks really
cool and rustic all right so as you come up the courses you need to start cutting around for your
electrical boxes and in our case invisible shelves so I want to run you through real quick
the tools and methods I'm using to do that so I start by making a clean edge on the bottom
of the fence picket so that I can line it up on the wall right where it's going to sit and I bring
it up to the electrical box then I could take my pencil and I mark both sides of the box I'll then
take a measurement from the bottom up to the electrical box I'll draw that out with my speed
square then I take a standard jigsaw with a wood blade and I cut that out as I'm attaching the
boards to my framing I have decided to go with construction adhesive the reason for that as you
see in this picture here these are very thin planks and they are very prone to warping with
changes in temperature and humidity basements have a mild change in temperature but the humidity can
change greatly in some areas of the country so I don't want these boards to be constantly fighting
against the staples I'm using so I'm gluing them down speaking of staples I have an 18 gauge
stapler here's a close-up of what the staples look like they're nice and long and very small
they're close together and they make a very clean pleasing look to my eye I'm going vertically with
them I decided to go with staples rather than nails because for every one shot you're getting
two piercings into the framing behind and then the crown of the staple tends to hold the wood
product in better now in the future we'll never be able to use a stud finder to find out where
we can screw things in for mounting and strength and whatnot but that doesn't matter because we
will have these running lines of the staples I'm using the laser level to keep both sides
of the window in line so when the boards join up again up here we're not way off
all the boards I glued up have sat overnight these four sets back here are going to make
up the window frame and then this longer one is going to be cut down to be
the top and bottom and the sides of that bigger shelf first I apologize for the backlighting here
of the window I'm exposing for the wood and for my face so it looks kind of washed out but if I
expose for the window it would look like this here all right so once I got the field of all
the wood done on the walls it was time to turn my attention to trimming out the shelves so I have
them all the way around and the faces glued and nailed in then I turn my attention to the
window frame once I cut those boards that I glued down to size I was able to put in the
sill which stands proud very typical several inches proud of the wall itself and that gives
it you know more of a substantive look and it makes the other trim details look really nice so
I have the trim all the way around the top then the apron down at the bottom and I have that
angled out a little bit very country farmhouse style also country farmhouse style is this top
here if you see this close-up detail I really like that little bit of flair there it's kind of
farmhouse style meets colonial or or federal something like that once that was all in
it was time to seal the wood now I chose to use a sanding sealer before I put on the top coat I
really like a good sanding sealer number one for me because it brings out the grain of the wood
and then it also has a very good property for sealing off so that discoloration and other
stains and things can't get into the wood as well once that was done I put on a polyurethane two
coats of polyurethane both of which were done with separate small roller brushes it made it
really easy for me to stuff self-level so you don't see that texture that you get out of a roller
I chose this varathane and it has two properties that I wanted three actually first it was odor
free this deft sanding sealer I love it just finishes so nice but it's really overpowering
whereas the varathane water-based has no smell at all two it is crystal clear so I didn't want
to impart any color into the wood I wanted the natural wood color and when we're doing exterior
or excuse me interior projects we can get away with no color as you move outside with the sun
and the uv beating down on it the more stained color that you can stand to impart into your
finish the more uv protection you will get and less chance of graying the logs or whatever other
exterior wood you have and then I chose a matte finish so typically you have satin
semi-gloss or gloss well a step below all of those is matte and I really like the way it turned out
there's no sheen at all it's a very flat color it really just keeps the wood looking as natural
as possible but the main reason I chose matte is because I didn't want my lighting for when I'm
setting cameras up to do recording here I didn't want my lighting to be reflecting off the finish
and being a distraction in fact if you look again at this picture and you look into the glass you
can see here that in the glass you have the reflection of my lighting that I have set up
for this shot and I didn't want that as I'm sitting here doing other types of reviews and recording
later on once my office is finished now while I was at it I also had this wooden trash can
I did not make this but I bought it years and years ago and I've never finished it
so I finished it in the same manner so that it will kind of go well and I'll have a little
trash can it's pretty cool it has a lid that comes off and it holds a tall kitchen garbage bag
just perfectly now that that is all done I can start wiring in all my outlets
and my lighting for the shelves and if you draw your attention up here you can see I still have
one row left to go up top and the reason I'm waiting on that is I want to first put in the
resilient channel and the sheetrock ceiling and then put that last piece in and maybe a crown
molding or something to support the sheetrock rather than having the sheetrock just kind of
hanging there without any edge support well it can get really chilly down here in the basement
especially in the winter when you're just sitting dormant and not moving so I chose this space
heater to go underneath the desk for a few reasons number one I loved the color it matched the black
cover plates and outlets that I wanted and it also is very quiet let's turn it on
so it's drawing air into both sides through little filter membranes and then just
casting out a nice gentle heat right here it can be controlled right on the keypad
through the included remote or very cool it has an app where you can control it when you turn it off
it goes through a one minute cool down cycle and then shuts itself off the only thing I noticed
that was weird is with the app turned off and I don't even have any batteries in this remote yet
it keeps turning itself on so I'm not sure if our remote upstairs or some stray wi-fi signal
is doing that or what well what woodworker or handyman's office would be complete without an
extra little added detail such as this french cleat I put four of these up to the right side
of the window and I built this little piece with the corresponding opposing 45 degree angle and
the offset and this is just out of one of the cutoffs from the cedar post picket it fits right
into there and perfectly holds our remote for the heater well there we go I'm getting excited to sit
here and edit this next video and get it posted now that we have the desk set up I can put up the
light box and then mount this camera wall mount and get that all situated and this project will
be complete amazing to think it was concrete like that just a few weeks ago so if you found this
video helpful you please give it a thumbs up it's really helpful to the channel also please consider
subscribing I'm working really hard to put out good quality content there's a lot more videos
to come on the basement and our next video is going to be up with a goat house that I just
built showing you how I made that out of an extra large crate and it's really helpful to the channel
now I'll leave links for several of the items I talked about the little can lights this space
heater or whatever else I might have mentioned tool wise full disclosure those will be amazon
affiliate links so if you click on them and end up making a purchase it won't cost you a thing
but I do get a small reward at the end of the month now in our next video on this basement
series we are going to be building cabinetry for right here it's going to house all of my electronics
my cameras my laptop so that the desk isn't getting cluttered and my cameras aren't sitting
out and getting dust on them and that's why I used these white outlets here instead of the black for
the rest of the room because I want to be able to open the cabinetry be able to spot them a little
bit easier and they'll be covered up so until then thank you for watching