Hi, I'm Mike with House on the Mend, and for Father's Day I want to show you how my daughters
and I have been transforming this bare section of our basement into this fully framed bedroom,
ready for wiring, insulation, and drywall. So let's get started.
Well, I'm actually posting this video on Father's Day 2025, so I thought it would be a really fun
insight for the viewers to see how I brought my daughters along for this process. This is going
to be my younger daughter Aspen's bedroom. She is 15 and has a great imagination, and it all
started with this drawing here, and we can break it up into three sections. There is the living
room section where she can have friends and entertain, have her TV and her couch. This
section she wants to be bedroom and closet, and finally over here we are pre-plumbed for a bathroom
that will come later. So with Aspen's plan in mind we went to our local Home Depot and we started
looking at building materials such as flooring and light fixtures, also bathroom fixtures, so she could
get an idea of exactly how she wants everything to be finished. We started over in the lumber section
and you can see here I taught her how to gun sight down the edge of a board to make sure it's not
warped or cupped. Then we went over and picked out the rigid foam insulation, more about that in a
second. We brought everything home and got down to cutting our boards to size. Now a very quick
recap on how I choose to handle the concrete walls is I want a thermal break in between the actual
cold concrete and the studs, and I accomplish that with rigid foam board insulation that
this particular brand Artec has this nice foil back design. Foil goes towards the living space.
On the bottom here we have pressure treated lumber, but I use a 2x6 so I can rest the foam
board on top of it. That way there's no chance if we have a leak down here that it ever wicks up
any moisture. And then we have our standard studs to frame out the section. If you want more
information on exactly how I did all this, please refer to another video in my basement playlist
which is the office build. I go into all this in much greater detail including how I adhere
the insulation and the tape I use. Now one of the differences from my office to this bedroom
is that we are going to be using drywall instead of that beautiful cedar board.
And because of that, instead of having every stud going the traditional way, I am every four feet
turning out a stud like this so that when the two pieces of drywall come together I have a lot of
area to put my screws in. I have noticed over the years that when you butt up two pieces of drywall
on an inch and a half thick stud that you oftentimes get blowout along the edge of the drywall
which is a lot harder to go through and mud and tape. So that's a little tip that I'm trying out
in this build. Now in my opinion the quickest way to secure your pressure treated lumber to the
concrete floor is to use a ram set. It actually uses a 22 caliber shell that will explosively
drive this nail through the pressure treated lumber and into the concrete. Now this triggered
one here works excellent. The only thing I have found is that it is really painful on my wrists
maybe that's because I've been using power tools my whole life and I'm well into my 50s now.
So I have been taking just a standard yoga block that is kind of cushioned and when I put the
ram set down onto the lumber I am holding it down to engage the trigger mechanism
with the yoga block to take up that shock. Now you might be saying Mike why don't you use this one
that they make that you hit with a hammer. This one I wish worked better because all you do is
set it into place after loading your charge in your nail and hit the top here with the hammer
and this is not at all painful on my wrists and it works good. The only problem I'm having and maybe
you can tell me in the comments what I'm doing wrong is every single 22 shell gets jammed in
here and many I've had to drill out. I actually returned the first one I had and got a new one
maybe it wasn't milled properly but on the very first shot again this one jammed in here whereas
the shells come out really quick with this more traditional trigger pull. Now in her original
drawing Aspen had dreamed up a walk-in closet and who can blame her they're all the rage aren't they.
Only problem is she wanted this actual bedroom space to be pretty small to give her more living
room space. It's really just going to have room for a nice size bed in the foreground here her
dresser over here a closet and then she wanted a place for the mirrors. So we instead decided to
make a closet with sliding doors that are going to be mirrored and that way it makes the room look
bigger to the eye when you have mirrors and the doors that would be for the walk-in closet will
also double as nice dressing mirrors. So for this closet we decided to go with two actual spaces
basically two doors that are going to be about four feet wide when they're done. They will ride
on tracks and just be guided by a channel up here so for that reason I did not have to make the
header anything substantial it's just a couple of two by fours. We have a power outlet inside here
because I want to put a small really nice looking remote controlled space heater right by the bed
it gets kind of cold down here what about perpetually 55 to 65 degrees depending on the
time of year. So that way I can hide the wiring inside the closet behind the clothing. Now as you
can see here it's passed through so you're thinking wow by the time you get to the
center your rod is going to be bowed down but instead what we're going to do is have half the
closet a nice built-in like this. I've installed those for customers before and they're really nice
and then coming off of the side of that built-in will be rods coming over here so in this back
section I'm going to reinforce with two by sixes so that I have a spot to secure them to.
Now if your girls are anything like mine they've already gone to the store and started purchasing
things to decorate the room so we're going to need a place to put all this and just like in
the office build I am going to install these floating shelves and we are going to light them
with the same circular led dimmable lighting as in the office build. Now one of my favorite tools
to have on a job site such as this would be a laser level. This one is made by Dovo. I did a
complete review on it and then I purchased this pole with my own money. I'll leave links to both
in the description below. So the reason I like them so much is you get both the horizontal
and vertical lasers. You can turn them on and off or all on at once. The nice thing about this is
the horizontal lines are great for the shelves. They're great if you want to hang all of your
electrical boxes on the same plane. They are fantastic for laying out for your window well
so that you can get them perfectly aligned with the window frame as you see here which comes in
when you're trimming later. Now the vertical line is just as important especially when putting up
the walls. So I like to use it to pre-mark where the floor plate and the top plate are going to
finally rest so that we know our walls are perfectly plumb. In this shot you can see Aspen
and I putting up the top plate. We had gone up to the joists that are the subfloor for the part of
the house above and we had marked on them where the laser level hit so that we knew when we put
up that top plate it was perfectly in line with the floor plate. Now unlike the atypical way I do
my perimeter walls in the basement, when it comes time for the interior walls I do them the classical
way. And that classical way is right here on the ground. It makes it so much easier because you can
use nails on the bottom and up on top to secure all these studs. So for the bathroom we elected
to have a standard square door opening. But for the transition between the living space and the
bedroom space, Aspen wanted an archway. So I've been working on taking plywood, rounding it to
the shape that would be equal to the standard door opening, and then cutting trim pieces here that we
can adhere some sort of cover. Now for our archway we have basically two options for filling in this
void. One would be if your local hardware store or supplier has quarter inch drywall. Your standard
drywall is half inch or five eighths. But if you can find quarter inch, the professionals will cut
that out and they will put a piece in, secure it, and then double it up with the second piece to get a
nice arch. But still have it be a half inch for when they do the rest of the opening. Now if I
can't just readily find that off the shelf, I don't think I want to spend the extra money to special
order it. So I'll probably just use eighth inch luan to trim out this area. Come back and fill in
the natural grain with joint compound, sand it down, and with a nice bullnose edge we'll never
know the difference. Now my older daughter Justice is home for summer for college and she helped me
to lift both of these walls into place. The first one here being the small one that separates the
living room area from the bedroom, and then this larger wall here. Now Aspen wants to have one of
those sliding barn doors or maybe two that split and open to cover this archway in case she's
dressing while she still has company in her living room area. So because of that I took the time to
reinforce up here with two by six lumber so that regardless of where we end up putting the rail
that the barn doors roll on, we'll have extra reinforcement. Won't have to worry about just
getting one little stud. Now I have two more tips for you on an interior wall. The first of all is
since I can't turn the two by four like I did on the perimeter walls for the two pieces of sheet
rock to meet, I'm instead just scabbing pieces like you see here so that I can put those two
pieces together on the four foot marks and have an easier time. Now my second tip when creating
an interior wall with a doorway, leave your bottom plate or floor plate intact across the opening
so that as you raise the wall both sides stay perfectly in line with each other. Once the
outsides are secure with your flooring nails or other anchors, you can come back in with a
reciprocating saw. I like to hold it upside down with the blade facing down instead of your
traditional way so that I can get the blade in here and cut out this plate as you see in this
picture right here. Now I know my face is backed a little by our nice bright hallway but this is
where all of the wiring is starting so I put a couple pieces of drywall here so I could show
you. Now way down deeper into the basement as you can see in the sub panel I installed I ran Romex
cable up through the ceiling joists down this wall by the bathroom all the way across and I'm starting
to put the wiring into the electrical boxes. So this is another two great uses for our laser level.
Number one, I like to have the wiring in a exact height all the way around any room I'm wiring that
way I know later on when I'm installing any cabinetry or any other furniture or doing any
other construction I know right where that wiring is unless it's going down or up the wall
and then of course the ceiling is really no problem at all. Speaking of going up or down
the wall I have a couple outlet boxes example here another great use case for the laser level
is all my boxes are at the exact same height at the kind of off the floor level. This one up here
is for Aspen's tv she wants to have a nice tv right here hanging from the wall so I am going
ahead and putting in an outlet box that will go behind that tv ahead of time. Keep in mind code
says within 12 inches of any electrical box you need to staple and secure your wiring to the stud.
Well as you can probably tell by the window wells no longer being brilliantly bright we're losing
daylight and I want to get this video uploaded for father's day so if you found this video helpful
will you please give it a thumbs up it's really helpful to the channel also please consider
subscribing this is just the first episode in this bedroom build that's going to take several
plus I have a whole playlist on my entire basement build as well as a playlist for my tool reviews
and I think you would find those entertaining and helpful plus it's free you just click on subscribe
and it really helps the algorithm to start suggesting these videos to more users that
might find it useful as well. Now by the next episode I will have finished putting all the
wiring in and these perimeter walls will be ready for rock wool insulation then we can put resilient
channel up across the ceiling joist which is a sound deadening item that I like to use before
putting drywall on the ceiling drywall on the walls and then we'll see how much time we have
left maybe the next episode where we get into all the really fun finishing details such as
the floating shelves trimming out the windows etc. Until then thank you for watching.