Making a bamboo bow, Tropical survival skills

Unraveling the Ancient Longbow
4 followers
8 Video Views·Dec 2, 2025
This is one of my favorite patches of bamboo to gather bow staves from.
Every stand of bamboo is different and only experience will tell you whether
the wood is good enough for a high performance bow or not.
But in general you're looking for a bamboo that has at least a four inch
diameter and a relatively consistent wall
thickness. You want to gather the stalks that are
the most mature which you can usually tell by the darkness
of the wood and how many aerial roots there are going up
the nodes. This patch has plenty to choose from.
I really like using these silky saws for cutting in the bamboo
because the blade is skinny enough to get in between the stalks of bamboo
and they're made out of really strong steel so they don't break as easily
when they get pinched which is totally inevitable.
In fact pretty much every time I do this I end up cutting
the piece of wood at the top before I finish cutting it at the bottom
so that it doesn't pinch the blade as much and it comes loose more easily.
I'm looking for a piece of wood that is going to be
as tall as standing it up so it comes to my nose
and that's for me generally around 62-63 inches.
You can see the base of this one is about an inch and a half thick
and at the thin end it gets down to about three quarters of an inch thick.
I wouldn't take it and use it for a bow if it got any skinnier than that.
So next I'm going to split the wood and I like to split the wood
in the direction that it grows so from the thick end
towards the thin end. I find it's easier to keep the split in the middle
when you split it that way as opposed to in the other direction.
So in a survival situation I would split this down
and dry it out by the fire but I have time.
So what I'm going to do is I'm going to split these down further and dry them
for a couple weeks and this is what it looks like after
drying for two weeks. This one's about two inches wide and
the finished dimensions of the bow is probably going to be about an inch and
three quarters to an inch and a half wide
when I'm done with it and you can see that it has a really nice profile
when you look down the length of it. So drying it more slowly just makes the
wood last a little bit longer and one of the things we have to contend
with here in the Caribbean is there's lots of termites. One of the
ways that you can make the wood more resistant to the termites is
to fire cure it and so if I were working with green wood
I could dry it by the fire and it would get fire cured while I dried it
but in this instance I'm just fire curing it for it to have more longevity
and I like to pass it right through the flames just quickly enough so that it
doesn't burn and char at all and I'm just looking for
a color change in the wood which you can see here the difference between the
light and the dark wood. So I actually spent more time fire
curing this than I did making the bow and you're going to see most of the
process right here. So you can see that I am using a machete for
most of the work here and I'm not chopping at the piece of
bamboo I'm sliding the machete down the wood and when I want it to
cut more I angle the blade so that it's facing
into the wood more and that causes the blade to bite.
Once I get the blade to bite then I flatten the blade a little bit more
to just split the wood off down the length of it. Now here you see me
removing just a little bit off of the thin end
that's all I need to do on the thinner end of this piece of
bamboo because it's naturally tapering at a good rate
and it doesn't end up needing much tiller. Most of the work that I'm doing
is on this side of the piece of wood which is a
thicker end and again I'm just using that technique
where I'm sliding the machete along the length of the wood
and just turning the angle of the blade towards the wood more when I want it to
take off more wood flattening it out when I just want to
carve the wood off on the little notch that I've already
started. So I'm trying to get the most poundages
that I can out of this piece of wood and it feels a little bit lighter than
I'd prefer it for it to be so instead of chasing down a perfect
tiller I'm just going to get this thing so that both
sides are bending the same amount both limbs are bending the same amount
and then I'm going to string it up. So you can see me carving
off some of the rougher gouges that I made with the knife and most of the
work is being done with my thumb here. My right hand is actually restricting the
blade from moving too much so that I can keep from gouging the
piece of wood. All I'm doing is getting the two sides
to flex the same and then right here you see me
making the tips carving down the tips. Once I'm done with all the carving I use
my machete at a 90 degree angle to the piece of bamboo
to scrape off all the carving marks and all of the
the worst looking marks left by the tools.
So all together the actual tillering of this bow
took me about 30-35 minutes and the fire curing took me about an
hour and a half. Here you can see me carving in the
notches. The only thing with when you're carving in the notches
especially on a piece of bamboo is to be careful
not to put too much pressure towards the end
of the notches so that you don't split out
the wood. I really like using a knife to make the nocks in my bow because it just
feels a little bit more hands-on than a file sometimes. Here you
can see me rubbing the piece of bamboo down
with some neem salve and again that neem is just to help
keep the insects off of it. Since I'm planning on getting a lighter poundage
bow out of this
this is my first stringing of the bow. Because I'm expecting it to be lighter
poundage than I'd prefer I want this thing to last as long as
possible so that I can maybe cut it down a little bit
later and get some more poundage out of it.
And that is the first full draw and it's not really making too much noise.
It's not the prettiest tiller in the world but if I tiller it down any more
it's going to get lighter than I'd prefer for it to be.
I have gotten 50 pound bows out of this stand of bamboo before but this one does
not feel like it's in the 50 pound range. So you can
see that the outer surface of the bamboo is
facing towards me and the way I'm drawing this back and
that's because of the characteristics of the bamboo and you
can see here we're right in at 42 pounds of draw weight.
So bamboo does tension really well but it does compression pretty poorly
and the outer surface of the bamboo does compression slightly better
than the inner surface of the bamboo. So this will get me extra poundage out of
it even though it won't last quite as long.
It's really easy to like my bow when you don't know what you're looking at kid.
And again this tiller isn't perfect but I just wanted to get the most poundage
that I could out of this piece of wood. It came out
super pretty and hopefully when I cut it down
or maybe back it or do something with it to
bring the poundage up hopefully it'll hold together but fun project.
Thanks for watching!
