Hey friends, this is a how-to video.
I wrote a book.
The bow I'm building today is building the bow
that I wrote this book about.
If you're gonna try to build this bow,
I recommend getting this book, but it's not necessary.
Oh, and we also put together a kit
of everything that's needed to build this bow.
It's on Shadowproof Archery,
as well as like all the products I mentioned and stuff.
I'm just gonna link all of those in the description.
So check that if you want, and I won't say that again,
so I don't say that over and over again.
But if I use a tool, it's down there.
I hope you enjoyed this build as much as I did.
Lastly, there is a playlist that is going to have
this entire series in it to build this entire bow.
This is part one.
I am super interested in making the best bows I can,
and I am super interested in helping you
make the best bow that you can.
And after making hundreds of fiberglass bows,
this is my favorite design that I've landed upon.
That curiosity brought me to wonder
if I can make the exact same bow design, but with wood.
This is a three-piece wood takedown bow
in the same design as my favorite fiberglass bow.
I had to make a few modifications to make it work from wood,
but today I'm gonna teach you how to build this.
You see, there's three things we need to build,
a riser, and then two limbs.
I've constructed this entire build
so you can get all the materials for under $100,
which is amazing.
And as a matter of fact,
you might even get it for less than that.
So here's all the material you will need.
And then next, let's start on the riser.
First, you'll need some sort of material for the riser.
It needs to be 3 1⁄2 inches tall,
at least 14 inches long,
and 1 3⁄4 inches thick.
In this scenario, I'll take two boards and put them together.
But the cool thing here is that
if you have scrap wood like I do,
you can add really cool accents
and laminate it however you would like.
But I do recommend a harder wood like hickory or ash,
or there's a ton of exotic woods
that I've built with that are harder.
The reason is these limb bolts
need to be strong enough to hold.
So you're gonna screw an insert into the riser
and the limb bolts need to be strong enough.
I've tried a softer wood like a spectra ply,
which is a bunch of like birch laminated together,
and that was too soft.
So I wouldn't use pine or poplar or anything
that's super soft,
but I would definitely recommend harder wood in the handle.
The strongest and most perfect scenario,
which isn't necessary,
is to have laminations this way,
as well as a curved lamination this way.
So the insert goes beneath the curved lamination
and is inside to there.
So it's technically with inside of three pieces of phenolic,
which is really strong material.
So with this type of riser, I'll test it later,
but I think I can go up to near a hundred pound bow.
Next for the limbs, you'll want a piece of bamboo.
This is a bamboo slat.
Also, I'm gonna use a piece of hickory.
In the last video, I made it from Osage.
You could do this from many types of wood,
but I would recommend hickory for the cheapest,
quickest, easiest way.
Then I've got two extra pieces of scrap wood
for the fade outs from the handle into the limbs.
Gonna use Titebond III wood glue today.
You could use EA40, but it's not necessary,
as well as a pack of limb bolt hardware.
You can accomplish this entire project
with an assortment of hand tools.
I'm not gonna just use hand tools today
because speed's important to me
so I can put out more videos,
but I'll give you the alternative to the tool I'm using
and what I would do if I were using hand tools.
Don't let your tools limit yourself.
You can be creative and figure it out.
That's what I did when I first started
bow making in an apartment.
I started with just this and a bucket knife.
I'm doing a three and a half by 14,
and then this is actually two inches thick,
and I'll thin that down later.
These spring clamps are super handy.
They're not super expensive,
and you can get a 20-pack really cheap online,
and you can use these for the limbs as well as the riser.
I live in a super dry environment,
so this wood will soak up the glue a ton.
Therefore, I like to do what I call as a sizing coat.
I'm gonna spread glue across the entire surface
and let it sit for about three to five minutes,
and then I'm gonna re-put glue on,
and I'll time-lapse this so you see
how much the glue just soaks into this wood.
Some people say this helps.
Other people say it's been tested and proven it doesn't,
but I think it does help with the premise
of not having a dry joint.
Now, I put a ton of glue on,
but if you look here closely,
it's completely basically soaked all the way in
and in a couple spots.
So let's add a little bit more and then clamp it together.
The key is no dry joint.
Slap those together, and then let's clamp it down.
It'll slide a little bit on the first couple.
No biggie.
As long as your boards are flat, it doesn't take much.
So let's let that glue cure.
In the meantime, we can work on the limbs.
That's a cool part about the three-piece take-down bow
is there's pretty much always something to work on.
Now, this is a bamboo slat.
It's crowned on the top, and these are the nodes.
I'm not really gonna pay attention to the nodes.
Not a super big deal today.
But on this other side, we need to make it completely flat
so we can marry together two pieces of wood.
One's gonna be the hickory, one is the bamboo.
It's technically a grass, forgive me.
But we need them flat so that we can put them together.
This is gonna add strength, a lot of strength.
This is the magic sauce that allows the limb bolts to go in
because this doesn't have grain like wood.
It's more like a sponge.
That allows the forces of the limb bolts to hold.
If you just try this with plain hickory,
I can almost guarantee that's gonna split out on you.
This is the magic sauce.
You can change the hickory to many other types of wood
that are good under compression,
but I would absolutely recommend
to use bamboo or fiberglass.
I'm gonna take this slat and hold it evenly
on the belt sander and go back and forth
until I get it completely flat.
If I didn't have that massive belt sander,
I'd use a smaller one like this or even one like this.
I've recommended this when one a lot for beginners
because it allows you to throw a belt on
as well as spindles and it's really cheap.
And for those who just have hand tools
or just want to use hand tools, this is how I would do it.
Take a cabinet scraper.
It's like a $5 piece of metal.
Sharpen it up.
If you have a vise, it's really handy.
What's happening is the cabinet scraper
is touching on both sides, but not the middle yet.
But it's a great way to remove the bamboo evenly.
It's gonna take more work, but in about 30, 45 minutes,
you can have this whole thing done.
I'll get it down to flat so you can see what it's like.
All right, now, if you take a look,
you can see how I've worked all the way through.
Now it's flat.
Can be done with a scraper.
Belt sander will save you a little bit of elbow grease
as well as 30 minutes.
I go on the edge of the belt sander.
I use light pressure, not hard, light pressure,
and always have the piece moving back and forth.
If you use hard pressure or don't move the piece,
it'll create a divot into your bamboo,
and then it will not have a clean glue-up later.
Always be moving.
Always nice, gentle, light pressure.
I highly recommend using your fingers,
and you can feel any part of the bamboo
where there might be a dip.
This is the, there's a little dip right there.
I'll smooth that out.
This is the best way to not have a bad glue joint.
Your fingers can detect
what your eyes can't see sometimes.
So how thick should you leave it?
Somewhere around two-tenths of an inch
is gonna be pretty good for any bow
between 30 and 60 pounds.
I did build a 100-pound bow,
and I left that one a little thicker,
closer to a quarter inch,
but depending on how steep your crown is, it can change.
I'd recommend bringing it down to about a fifth of an inch.
Nodes, always a question.
How evenly should I space them?
Is that important?
What should I think about there?
Evenly spaced nodes makes tillering easier,
but it doesn't necessarily make the bow perform better.
We're having 32-inch limbs,
so I'm gonna find an even distance between the nodes
where I can go 32 inches on either side.
Then I'll cut it there for each limb.
The most important thing with this bow
is that our limb bolts don't fall exactly where a node is.
So you'll also hear there was a node right here,
so I cut on just on that side of it
so that the limb bolts, not where the node is,
and then the first node is down here past the fade-out.
Same thing on this side.
So from this node, I have 37 inches in one direction,
and I have 34 in the other direction.
That's perfect.
So I'll cut my line right on this node.
This side connects to the riser.
So I'll measure down 32 inches,
make my mark, and cut them both there.
Bamboo's prepped.
Now for the wedges.
I've already cut these down to a decent size.
We're at eight inches long.
That's important.
And I've thinned them to 1 1⁄10 of an inch on the sander.
So this piece will be this piece.
It's a critical piece to work.
It stays thick for these first three inches,
and then it gradually, super gradually
tapers and feathers into the limb.
What this allows the bow to do is not to bend in this area.
You'll see the total thickness
is 3⁄4 of an inch right here,
but at the end of the fade-out, it's half an inch.
So this piece gives the strength we need here
to not have it break.
Therefore, I'll mark at the three-inch mark,
and I'll do the same on this limb.
Don't touch this area.
We want it flat.
Also, don't touch the back.
We want this side flat, but we want the bottom flat
so that it stays flat along the core material.
This is an exaggeration to show you what I'm trying to do.
That's what the wedge is like.
Flat on this side.
Don't touch these first three inches.
This is a properly feathered piece,
and you can see how gentle this bends.
It's paper-thin and then comes back
to our 1⁄10 of an inch.
I forgot to mention that this type
of material doesn't matter.
I've tested fiberglass, I've tested bamboo,
I've tested softwoods, I've tested hardwoods,
I've tested all sorts of things,
and I would choose the insert
that gives you the look you want.
So I thought it'd be cool to add a dark accent
in these limbs, so I did walnut,
and it's scrap I had.
The riser's curing, the bamboo's ready to go,
the fade-outs are ready to go.
Now, it's time to work on the hickory.
Hickory staves like this can be picked up online
or at a hardware store.
This one is so thick, we need to thin it down.
I'm looking for a finished dimension
of 4⁄10 of an inch on this hickory stave.
So with this one, I'm gonna take it to the bandsaw,
cut it up the middle,
and that should allow me to have two pieces.
Now, the reason I'm not leaving it this thick
is because I wanna add a little bit of reflex
into this bow to help it shoot even better.
So the limbs need to be thin enough
that they can bend without breaking
in the glue-up process.
Additionally, once it's split in half,
that allows you to make two full bows
out of this one 15, 20, $30 piece of wood.
My favorite tools for flattening it after sawing it
would be a drum sander.
Most people may not have that,
so a planer actually works really well,
or just on the belt sander to prep it for the glue-up,
you can do that as well.
Hand tools, of course, will work, but just take more time.
Good news.
Now we just need to cut this down to 32 inches
to match the length of our bamboo.
Something I've always done for bow making
is to use a hacksaw because the teeth are so fine.
It allows me to never have split out.
And now we're back with our riser, our bamboo,
our limb fade-outs, and our hickory.
That's all the pieces we need.