Repairing The FM Band And Low Volume On This Westinghouse Tube Radio

Amateur Repair Time
257 followers
176 Video Views·Oct 19, 2025
This is a Westinghouse H-307t7 Tube Radio, a very plain model but beautiful in it's own way.
Check out our Patreon page, for all of our channels. Contains outakes, concise arcade repair tips, bloopers, repair FAILS, Audio youtube wouldn't allow us to upload, and much more!
https://patreon.com/JoesClassicVideoGames
------------------------------------------------------------------------------------
Ladies and gentlemen, welcome back to
Amateur Repair Time. We've been working
on uh this old school Westinghouse
radio.
It is
a Westinghouse H 307 T7,
just so you know.
Uh not to be confused with the H308 T7,
which is the ivory. We've got the brown.
I bought this at the flea market for 15
bucks or something like that. And all of
the uh tubes were missing. And so we did
a video where we uh recapped it and we
did some resistor work and we did a
video where we did some tube work and
we've got it working just barely.
It's picking up a blowtorrch station on
AM. the FM isn't working and uh very low
volume on the the one channel because we
don't have an antenna even hooked up.
So, we're trying to
uh stumble our way through it and figure
it out here. So, like I said, we've got
one channel.
>> This is a 50,000 watt channel that's
like four miles from here.
And that's all we can get. Nothing else
comes in. Um,
we I brought it up on the variac and and
all of that, but now I've just got a
straight voltage going to it. Um,
everything seems Oh, we still got to
mess with this uh
selenium rectifier. We got to get rid of
it, too. Um, but I think the first thing
I want to do is try to figure out why
we're not getting anything on FM. So, I
guess I turned it off when I shouldn't
have.
Let's switch it over to FM. And the
first thing I'm going to do
is just wiggle some tubes. Good old tube
wiggling. I didn't clean the sockets on
the tubes. That might be the whole
freaking problem. What do you think? So,
there is a nice little diagram here.
It's going to show us which tube is
what.
Let's see what we got going on. Now,
this is amateur repair time, so we'll
just have to stumble around. So, the
output tube to me
seems like it must be working. What do
you think? Don't you think that's pretty
fair to say? The output tube must be
working. We're getting lots of hum.
We're getting that one station in. And
so it's outputting that has nothing to
do with the FM.
Okay. So this this 12 AV6 the AM
detector uh the audio auto volume
control and the audio tube. That must be
working because it's AM. Okay.
The 12 AL5. I actually ordered those new
old stock. tested them and they they
tested really freaking good.
Uh but it is just the FM so you know
that's suspect.
The 6R the 6BJ6.
What is that saying? FM. Let's see what
it says down here.
FMIFF driver.
Well, I don't think we have an IF
problem. Um,
I think we've got an RF problem.
So, the difference being
if you had an IF problem, I think you'd
get something. You'd be grabbing
something out of the air. It would just
they'd all be mixed on top of each other
or the uh that speaker looks bad, but
it's not. It's just a like a ripple.
It's not actually cracked. I mean, the
the inside is, but this is actually
complete as long as I don't play with it
too much. Uh,
if the IF was a problem, you would still
get some stations. I think they'd just
be laying on top of each other or, uh,
you know,
not coming in very strong or whatever.
If you're if you're not getting anything
on FM, not one freaking channel, it's
either going to be like an antenna thing
or a RF thing. I think it's not getting
it out of the air, folks.
So, I think that gets us down to
the 12 AL5, which again is new old stock
and tested rock steady, like really
strong.
Uh or this FM RF mixer. Oh, wait a
minute.
The 12B6 is the FM oscillator and the AM
converter. So, it could be that very
well too.
Where is that? That's here. H.
So, we've got this strange thing too
with the uh with the antenna. So,
let me read you what it says about the
antenna. Where is that? Where did I see
that? The FM antenna.
Antenna information.
An external AM antenna can be coupled to
the set by taping the leadin wire to the
outside of the rear cover as shown in
figure 3. The wire should be dressed in
the position shown and can be held in
place with adhesive tape or other
similar material.
And they show it to us.
Here we go.
So, it took me a while to figure out
what's going on here. They are actually
just showing you that on the back of the
radio. So, this is our back. Somebody
scribbled on it. I wish they wouldn't
have done that. I might try to actually
I might be able to get that off. What
happens if I take just a little bit of
paint thinner and rub on that? What What
do you think? I think that might clean
it up a little bit. I think we're going
to try it here in about 3 minutes. Um,
but they're, if you look on the inside,
you know, you've got your loop. And so
they're saying, "Hey, just tape a wire
on the outside and it'll couple in
through the loop."
So that's not actually connected. It's
literally just taped to the to the back.
Um, if you've got like a 50 foot long AM
uh, antenna you want to put on it, the
wire should be dressed in the position
shown and can be held in place with
adhesive tape or other similar material.
All right, so we don't have to worry
about that. The reason we're only
getting the one AM station and very
weakly is because I don't have the
antenna even hooked up. I just showed it
to you. It's not even connected. But
that one station is so strong here
locally that you can grab it even
without an antenna.
All right. And then we have this.
The blue wire emerging from the hole in
the rear cover is a line antenna
for FM reception.
It should be connected to the left
antenna terminal as shown in figure
three. Well, the problem we've got with
that is they have
ripped all this loose. So, I don't know
how this crap was set up originally.
Was there some kind of like quick
disconnect or were they soldered
originally? Or I mean, it kind of looks
like everything was soldered, but then
you have the problem
where why did they use that?
We're gonna mess with that, too.
Uh, so the left one.
It's on FM.
So, the blue wire should go out and
attach to the left
antenna terminal as shown in figure
three.
All right. So, we need to figure out
what wire is the blue one.
and what wire
goes to the left antenna terminal. But
I've already figured that out.
Um, look how this is done, too. We need
to get it back to this.
So,
this is that wire. It's this long wire
here. And if you look, it goes up. and
they show it
attached to that screw. And then the
other wire goes to a 33
microfarad cap which goes to pin three
of the 12 AT7.
The 12 AT7
is located on the left side of the
chassis on the back.
So, I have actually searched that down.
And here's our long wire. And then that
is the blue wire that they were talking
about.
No, that can't be right. I've got that
I've got to have that wrong.
Oh, no. I'll bet it is right. So, that
goes onto the I'm nowhere near it. It
looks like I'm about to touch it. It's
only one I don't want to get electro
killed. But that wire is the one that
attaches to the left terminal
um on the back whenever it's soldered in
place. And then that other wire is the
blue wire. So, um
boy, that one there sure looks like the
damn blue one, don't it? Wonder if I've
got the freaking antennas backwards. All
right, so I'm going to turn it off.
We'll look underneath.
We'll trace all those out. We're going
to get to the bottom of this, folks.
Don't worry. All right, so we're
unplugged. The wire is disconnected and
all that. It was just loosely hooked up
anyway. So, we've got this one really
long wire, right? And if you look over
here, it comes off of a little uh
um
domino, we'll call it.
And then the domino connects to one of
the power leads.
Okay.
So here are the power leads.
There is the domino I'm calling it. And
then there is the long one. So that is
obviously that one. So it connects to
one of the
terminals
uh on that antenna. Now the other wire,
the wire that is supposed to connect to
connects to a cap
and then to pin three of the 12 AT7. The
12 AT7 is the last one.
So
this is the 1287.
There is a cap that connects to pin
three.
So, here is pin three.
Boy, I'm going to win some awards for my
camera work on this one for sure.
Pin one, pin two, pin three.
Is that correct?
Yes, that's correct. There's pin eight.
Okay, let me look a little closer. Let's
I don't have enough light here. Let's
see if we can put some more light on the
subject. A little more light.
I need a screwdriver or something,
right? manipulate it.
Well, we'll just have to dig in there a
little bit. Pin one, pin two, pin three.
So, clearly
this is pin three.
Orange. Orange. Black.
Orange, orange, black.
Uh, which would be
33
33
33,
right?
And then L8 is the other thing that uh
is obviously connected to it. And so
that wire is the wire and it should be
connected to the big long wire.
So this wire
this wire
and I've got it connected to the big
long wire. Okay. So that's that. So,
we've got the right one hooked up. The
other one here is coming off of the
capacitor,
which is that connection right there.
It's going to go into the loop.
All right, that's that one.
This one.
It's coming off a 33meg.
Maybe that's 3.3 meg. 33 meg. I think 3.
Are we right?
Yes, it's coming off a 33meg resistor.
Um,
that is going to connect to something
that leads back over to the U switch.
So perhaps it's this other one
3.3 meg resistor.
Uh and then the other side of that
leads over to the switch. Okay. Yeah.
So,
this is one of our AM's.
This is one of our AMs.
And then this one must be the other FM
one.
What the crap?
So it leads to there
which is
that ground
connected through a cap
underneath this filter cap
to ground.
Okay. Connected through a
0.01
to
ground.
Connect through a 0.01 to ground. Yep.
All right. So, the only thing is
I guess we've got to assume
that this one with the arrow was the
blue one.
one that sure looks blue, doesn't it?
We don't really have a way of knowing
which one is the one that disconnects
when you hook up the antenna
because they're telling you the color
and I don't completely understand how it
works. So, I don't know off the top of
my head which one you would disconnect.
Blue wire
should disconnect uh if you're using an
external FM antenna
H.
Well, let me think about that.
Maybe that connects to Well, Damn. I
just don't understand how that would
work. It's got to be the one that's got
two connections. That's the only
explanation. So, it only makes sense
that this is always hooked up. And it
doesn't do anything. The only purpose of
it is if you're hooking up an external
antenna, you would hook to that. And
then if you are hooking up an external
antenna, you would unhook this wire.
That's why it's got the little arrow on
it. That must be the blue wire. You
unhook it and it leave it hanging out of
the back of the antenna,
which means that there is a damn good
120 laying there for you to get zapped
with.
Wouldn't that be some crap? Um, you
leave it hanging out of the back of the
of the cabinet and you put your external
antenna on it.
um
which would you know then your antenna
would go to this
uh FM RF mixer. I mean that's the best
guess I can make. I
It does seem weird though that they
would have 120 volts hanging out of the
back of the freaking
radio,
but that's kind of how I would guess
that goes. Hm. You know what I think
I'll do? I'll look online and find
somebody else's
and see what the back of theirs looks
like. What do you think about that?
All right. So, uh, I think we've got the
antenna hooked up, right?
And we don't have an external antenna
hooked to it. I guess I could try to
hook up an external antenna to it, but I
don't think that's what's going on. I
think we've got it right. I think that
we've got a like a tube problem or
something even though I checked them
all. And it could just be a tube socket
problem. So, I'm going to turn it back
over. We're going to turn it back on on
FM. And then we're going to wiggle some
tubes a little bit and see if we get
anything different. All right. I may be
getting a little bit of a uh clue here.
Here, I want to show you
now on this one doesn't have a pilot
light, but on a lot of them with a pilot
light, when you first turn it on, the
pilot light will come on and then
immediately go back down and then come
back up. Right? So, I'm getting that out
of the 12 AL5.
So, it comes up
Growing strong. Glowing strong.
I don't.
All right. So, we're on FM. I think the
antenna's right.
You know, I ought to be getting all
kinds of like
static, you know.
I'm getting So,
[Laughter]
Work with me now. Come on now.
Dead as hell.
Nothing. Not even a peep of anything.
All right. So, what's the other one?
The RF mixer is all the way over to
1287.
So, that's this one.
Did you hear something?
>> Yeah.
I wonder if it's just way out of
alignment.
We wear pink to celebrate breast cancer
awareness month and we had a celebration
a celebration of our survivors
who have passed away from the disease.
>> Good morning. Who you celebrating? My
mom
13 years.
>> What's our other one? We had another um
FM one.
The FM oscillator. Oh yeah. The 12B6 is
this one here in the front.
>> Don't shock me now, Mr. FM off. Please
don't shock me, Mr. FM oscillator.
98
R&B
single
Well,
>> we got some kind of low volume on
everything.
I mean,
>> so, you know, I'm filming this on a
phone and it's so it's it's compressing
everything for the video.
Just my personal opinion, the the if
this is capable of a 10 in volume right
now on this best channel that I can get,
I'm getting a three. It may sound louder
than that to you, but it's just I'm not
getting any volume. So,
>> we uh we could measure some voltages
on some of this, but I think what might
be more
uh
I think what might work better for me is
to just swap a couple tubes. Like I keep
saying, "Oh, the output's fine. The
output's fine." Well, it's awful damn
quiet for the output to be fine. And I
wonder if uh my
I've got I've got a,50 C5s. Maybe I'll
just swap one in just to see if we get
anything any different. So, I think I'm
going to mess around with uh cleaning
some sockets with uh contact cleaner. I
don't have any deoxid. It's too
expensive. I mean, I can afford it, but
that crap is expensive, people. I can't
I can't in good faith buy it. But I do
have some contact cleaner. So, I'm going
to clean the sockets with some contact
cleaner and I'm going to try swapping
the 50C5
um because I've got like 50 of them. So,
I'll just I'll try a couple of them in
there. See if that makes any difference
at all. And uh I'll try swapping out
some of the ones that I have extras of
just to see if any of them make a
difference. If they don't, then we'll
just try uh um we'll try uh uh aligning
it. Now, the good news is I don't hear
anything that sounds like silver micica
disease. On the on the previous video,
we were thinking that might be going on,
but
>> I mean, there's no there's no crackling
or anything going on. So, I'm cool. All
right. So, uh yeah, I'm going to let me
see what I can figure out and I'll come
back. All right.
So replacing the 12 AV6 which is the uh
the AM
but also the AVC
um got me a little more volume. So I'm
still going to check some voltages
though just to see if again I went
through all the resistors but maybe I
missed one or something. Um but on a
certain channel you know you get some
pretty good volume.
[Music]
But I would still say it's only like a
five. You know, it could be maybe the
speaker's bad or something. You know,
that tweeter part really is kind of
screwed up. Um, let me switch it over to
AM. See if we are still getting AM for
one and see if it's if that one good
channel has any more volume even with no
antenna.
A horrible thought just went through my
mind.
What if the silver micica problem
is only on the AM ones?
Yeah, we just got no volume on AM, but I
think it's just because there's no
antenna.
[Music]
Mhm.
>> All right. Okay. So, I'm actually I'm
going to clean the last few sockets that
I tried swapping out tubes on almost
everything. Um I'm going to clean the
last couple sockets and then we'll go
from there. All right. I have found the
problem. I found the problem. So, I
substituted in a tube for each one. Um,
all I did was find some bad tubes that I
was substituting in.
Right. So, I'm at the point right now
where um it we get volume on certain
things, but it's not as loud as I
thought as I think it should be, for
instance. Right. So, this is probably
the loudest channel. I apologize in
advance for the horrible freaking music
they're playing.
[Music]
I honestly think it's at like 30% 40%
maybe, right? But
you know, you know what's you know
what's going on, people. All of you
old-timers are going to be so happy with
this. Oh, the shot in Freud's going to
freaking kill you.
96 volts is all we're getting out of
that thing. Um I wonder if I can test
the AC going in. Let's see if we can do
that.
Yeah, we're only getting 96 volts out of
that thing's starting to fail. I tested
it whenever we did the first video or
the whatever maybe this I think the
first video, but like I mentioned in the
in that video, that was without a load.
I didn't have the any of the tubes in.
Let's see if we can get anything on that
side.
Yep. And so there we go.
121 volts AC going in, but only 96 volts
DC coming out. That would do it every
time, wouldn't it?
That would do it every time.
Yeah, we should have 149 volts coming
out. So, we are
highly crippled.
So, we're going to have to get rid of
that. Uh,
I would love to put it right where it
is. I'm just going to get rid of the
damn thing. I'm going to remove the
whole thing. Um,
this, you know, this is not a Sometimes
whenever I mess with these people go,
"Oh, keep it a ridge. Stuff the caps.
The hell with that." This is not a a
high dollar re, you know. I just want
the thing to work good and look
reasonably good. I don't I don't care
that it every little part inside of it
looks looks uh original. Um
but that's our problem. So that makes
complete sense.
We're just we're not getting enough
volume because we're not running
everything at um at its capacity.
Okay. Okay. So, let's see what I can rig
up for a
diode and a resistor
to try to get that right. Um,
I'll have to do some math.
I didn't know there was going to be a
math test.
All right, folks. We are kneede in it
now. So, first of all,
I uh
desoldered one of the wires from the um
the selenium rectifier and so I got a
little whiff of that smell everybody's
always talking about. It's not that bad.
I've actually smelled it before. I don't
know what that is, but
it kind of smells like rotten eggs a
little bit, but it's not. Everybody acts
like, "Oh, it's the worst thing ever."
Yeah.
I don't know. Maybe I'm living uh
rougher than most people. I don't know.
I don't know. I'm a pretty hygienic
person, but it it does. I'm s I'm
showing you. Look, my room's pretty
clean. Um
it's not it's not destroying me. I'm not
that worried about it. Okay. So, let me
explain what's going on here. I got a
lot of stuff going on. I blame
Shango066.
It's all his fault. Um, so I got about
10 things we have to go over. So
yeah,
I left that in there and the only reason
is because they had two wires coming out
of the output.
And so what I did was I just moved the
wire that was going to the input,
which was the AC originally,
uh,
over to the output. Okay. So I'm just
using it as like a tie point.
I guess I can just leave it like that.
Um, okay. So, we got our AC coming in.
I've got it upside down and it's it's
it's uh propped up on this uh can. Look,
folks, there's nothing wrong with that.
Don't worry about it. And the wires are
just kind of hanging there cuz I got and
I got the battery on it to weigh it down
to make sure that they stay on the post,
you know. Now, I understand all this
needs to be rectified.
Pun intended.
Um, yeah. So, there is a, now I'm not
going to touch this. This is all running
right now. It's hot. Okay. There is a
long terminal strip right there. There
is actually an open spot right there,
which you could use, but I didn't I
didn't quite have it in my head exactly
how I was going to do it yet, and I
found something on the schematics that
changed my mind. it. So, I went ahead
and tacked in this other terminal strip.
Uh, but I really didn't need to do that.
Okay, so we have the AC coming in and
then it originally jumped through a
resistor that ironically
I had already replaced. So, this I put a
20 in there and it calls for a 22
and we did that in the second video, I
believe. So, here's the AC. It comes in
comes over here and it goes through this
R17 22 ohm resistor and then into the
selenium rectifier and then we want 149
out the other end. Well, whenever you
replace the selenium with a silicon
um uh rect uh diode, what happens is
usually you get more voltage out of the
other end because it the voltage drop is
different across the selenium rectifier
and a silicon diode,
right? So, you have to put a resistor
after it to get the DC voltage down
where you want to go. But the way this
one's designed, they've already dropped
the voltage, the AC voltage with that
R17.
Um, so I was planning on putting the
diode and then a resistor, but then I
started to the resistor on the DC. But
then I started thinking, well, why would
you know the cleanest way to do it is to
just change that R17 until it gets the
120 because it's not it's not using it
for anything, right? So, I don't, you
know, it just depends on your set, I
guess. But, you know, that voltage, so
it's 120 here, and we're it's doing the
string, and then it's 120 here, and we
already looked at that. It goes off to
the antenna. Um,
but right here the only thing the 120 is
doing is feeding the selenium rectifier.
So if our goal is to have 149 volts on
the other side,
uh, we can we can accomplish that with
that R17 just changing the value of
that. So I removed it
and then I hooked up jumper wires to
this decade box that I've got now. This
decade resistor box. Now, this is not a
power
decade resistor
um
uh power supply box. So, the reason
that's important is because these things
can only handle so much amperage. So,
you can actually see
at 100,000 ohms, they only want 1.6
milliamp across that thing. 10,000, I
only want 5 milliamp across it. It's
because this isn't a power resistor box.
Uh 1k ohms, they only want 16 milliamps
across. 100 ohm steps, they only want 50
milliamps across. And uh 10 ohm steps,
they only want 160 milliamp across. 1
ohm steps, 300 milliamps. And if you're
trying to just do 0.1 ohm resistance
with this decade box, you can run an amp
through it. But the thing is, you know,
the current is what it's what the
resistor is dropping it. So there's not
really a ton of current, but it's
probably something like, I don't know,
50 milliamps or something like that.
So because of that,
this would be pushing it. That says max,
you know, so I don't want to go over a
100. But if I'm down at 100 or under, I
can use these three basically.
These three I can I can I can use um
without it burning up the decade box.
I also looked this thing up just trying
to figure all that out and apparently
these things are worth hundreds of
dollars. I didn't realize that. I bought
it at an auction and I paid like five
bucks for it a while back and it's just
been sitting around and I I saw that
Shango did this in a video but he had
the right one. He had the uh he had the
power resistor box. I saw I saw him do
it and I was like, "Oh, I got one of
those." But then when I pulled it out, I
I was very carefully reading that and
going, "Wait a minute. That's not going
to work very good." So, this is you're
not really supposed to do this for this
application the way I'm doing it. But
this is this doesn't quite have enough
uh backend theory on it, but it is
working. Um,
so I have basically substituted in the
decade box for the resistor that we need
to help me figure out which what size
resistor we need. So now the power is
coming in. It's jumping through the
decade box and then it's going through
the diode
and then it's going out the line
to tie in where the other two lines were
coming out of the selenium. So that
would be
right here. One
uh is going to the cap
and one is heading off to the output
transformer.
Okay. So, I'm taking
AC in and running through the decade
box.
And then the the U
rectifier is here. We're getting rid of
that because we're just using it as a
tie off point. We're not running
anything through it. Bam. So, we're
good. So, I have got this thing set up
with a 100 ohm, the decade box set at
100 ohms. And I even tested it with my
meter just to make sure and it is at 100
ohms. And so if I do that, the DC
voltage that we're ending up with is 128
volts, which is too low actually. So
we've got too much resistance. And with
it like that, I've got my volume that I
was looking for.
And we're getting nice reception on FM.
We still haven't aligned it or anything.
>> So, we're getting lots of channels in.
Everything's cool. Um,
let me go back up towards the top of the
dial.
I'm trying not to get electro killed.
All right. So, everything's working
cool, but we're too low. So, I thought
I'd show you if I turn down the decade
box. We'll see if it either blows up the
decade box or raises up our voltage. So,
I'm at 100 ohms.
I'm going to go down to 90 ohms.
Okay, I'm going to go down to 80 ohms.
It's giving me two volts each time. 70
ohms.
60 ohms. I can see where this is going.
Can you see where this is going? 50
ohms.
40 ohms
30 ohms.
30 ohms gives me 148.6.
It's calling for 149. So if I was to
have left the 20 ohm resistor in there,
my voltage out of the the the silicone
rectifier would have been about right.
So, really no mod needed on this one,
but we'll we'll modify it a little bit.
Um,
strange thing, too, is that's a one
it's only a one watt resistor that it
calls for, but
you know, a lot of times when people do
this, they'll put like a five watt
resistor in it or even a 10 watt
resistor in it, but they're doing it on
the DC side, so I don't know if that
changes it or not.
Um,
but we're right there at it with 30
ohms. And I'm I'm sure I could change,
you know, make it 33 ohms or something
and have it dead on the money, but I
don't I would rather it be just a little
bit low anyway. So, you know, um, let's
see if the reception or the volume's
better.
So, that's all the way up basically.
It's time for higher
Let's
keep
[Applause]
them.
All
right. So, we're working.
Let's turn it up to AM. See if we can
get anything in on AM at that voltage.
Remember, we only get that one channel
because there's no antenna hooked up.
somewhere around through here.
I don't think it likes being turned
upside down. All right. Well,
>> the best day ever.
[Music]
>> All right. So, I think we got it. I need
I just need to put a 30 ohm resistor in
it and I'd like to get like a 5 watt or
something. Um, but again,
it calls for a one watt in that
position. Now, I realize as the
resistance goes up, you need more
uh you need more wattage, but you know,
we're going from 22 to 30. I mean,
a two watt would probably work.
So, that's my thinking. All right. Well,
I've got it pretty clean underneath.
Um,
with the exception of the resistor being
missing.
Um,
we're kind of ready to clean up the
cabinet,
align it, and see if we've got a problem
with the u uh silver mica disease on the
IF cans. If we do, I don't know what
we're going to do. And uh we need to
hook up the antenna for the AM, put it
all back together, and see uh see what
kind of work we can get out of it. That
back cover that mounts on here, um I
think it's kind of meant for you to
remove the whole chassis at the same
time because that cover the wires have
to solder to the cover. So, you can't
just remove the cover. And it's strange
because you it also has that power
connector there. So you can remove the
cover to remove the power from the
chassis, but then you have the problem
where the antenna is permanently
attached to the
chassis. So you can't go far with the
cover and that's how the thing got all
ripped up.
So I think it's meant to be, you know,
pretty much permanently attached to the
back of the chassis with that bracket
and you just remove the whole thing at
one point. I mean at one time. And these
are not uh meant to be these are
soldered on. I I I saw some videos and
found some pictures of other people's
and the wires are just soldered on
there. There's no quick disconnects or
anything, which makes sense because
there's four different wires or five
actually. Um
so you wouldn't want people to unplug
all of that every time they took the
back cover off. So, I think you're just
meant to slide the whole thing out at
once and then maybe disconnect the back
cover if you're working on it, you know,
because it says it says disconnect the
back cover before you service the
chassis because it wants you to unplug
that. So, I don't know if it was just
something where they were trying to
appease the FCC or something or what the
deal was, but
it needs an alignment bad though. So, uh
yeah, that's where we're at. So, let me
see if I can find a resistor for that or
order a resistor for that and then we
can at least
set it up and stop having it upside down
all the time.
>> Okay.
[Music]
[Applause]
Even I haven't been abducted, but I had
an alien being try to do medicine. And
they've done this to many.
>> Tried to do what? And they tried to sit
inside of you.
>> Oh no.
and let them know the new Donnie
McCluren show is on the air.
>> Oh no, he's trying to He's trying to get
in on my theme song. What?
What?
It's like
It sounded very similar to my theme
song. I I don't know. I don't know.
So next time folks, like I said, we're
going to clean the cabinet. We've got to
align this thing. I've got to do more
cosmetic stuff. Like I got to replace
this. But there again, there's no light.
So that's just like a color to give you
contrast for the the the uh tuning
indicator when you tune through. So
let's see what else we can find on here.
>> I'll see you on the next one.
>> Wait, what? What is this?
[Music]
Ladies and gentlemen,
>> sitting
[Music]
[Music]
in schematics
[Music]
and thrifting
[Music]
last
[Music]
new
[Music]
tracing faded
vacuum to blows. Get it back to working
by the end of a show.
Bringing broken gadgets back to life.
Turning silence into stories one at a
time. We fixing to fix easy as can be.
amateur at bedtime for you and me.
[Music]
Little machine, you carried history.
Time to trace your path. Bring your
sister from open to singing Suffocate
[Music]
cables, switches
[Music]
tangled up
[Music]
clocking.
Take back
[Music]
tracing faded traces back into
it
by the end of the show.
Bringing broken gadgets back to life.
Turning silence into stories one at a
time. We're fixing to fix some easy as
can be. I'm at your repair time for you
and me.
[Music]
It's
time.
[Music]
It's bad time.
[Music]
