I've Had This Nice 1953 Columbia 360 Record Changer For Years! Let's Fix It.

Amateur Repair Time
257 followers
153 Video Views·Aug 17, 2025
This is the Columbia 360 "Mark II" , which was the first "360" Columbia released. You can hear more video of it on our patreon channel.
Check out our Patreon page, for all of our channels. Contains outakes, concise arcade repair tips, bloopers, repair FAILS, Audio youtube wouldn't allow us to upload, and much more!
https://patreon.com/JoesClassicVideoGames
------------------------------------------------------------------------------------
Ladies and gentlemen, welcome back to
Amateur Repair Time.
I am
working on all kinds of stuff right now.
I've uh been working on a bunch of
clocks. You can hear some of them in the
background. I've been working on this
grandfather clock, which you probably
just saw the video for, cuz whenever I
finish that up, I'll probably upload it
before I upload this.
Uh I'm working on a TV and I'm finally
going to work on this. I've been meaning
to work on this for quite a while. This
is a Columbia 360
record changer. Also known as
uh the oldest the first well I shouldn't
say the first the oldest record change
the record changer that I have had the
longest. We'll just say I bought this
about 20 years ago and I listened to it
maybe even it may have been 25 years ago
and I listened to it for quite a while
and had it here in uh at the house and
would play records on it all the time
and just loved this thing and um
it just died on me one day and stopped
working and at the time this was before
I even worked on electronics.
I didn't know what the deal was. I never
messed with it. Didn't open it up,
nothing. You would plug it in, it
wouldn't work. And it's old enough that
it's tube based. So, I'm sure there's a
bad tube or a bad cap or something. So,
we're going to finally fix it. Now,
I'm going to keep this. I'm not going to
sell it because I've had it forever.
The clocks are going to start doing
their thing. I've had it forever and um
out of all the ones I've got, this is
the one I would want to keep. Now, check
this out. Now, there's nothing really
all that special about it
other than I've just had it a long time
and I like it. It's very dusty. It's
been It broke probably
another clock. It broke probably I don't
know 15 years ago. It's been sitting
around forever. So, all this dust.
Look at that.
Um,
I can't remember what broke on it. Maybe
it just stopped outputting.
It's got I don't think that's a crystal
cartridge. I think that's a ceramic,
which means that I should get away with
keeping the same cartridge. Hopefully.
So, hopefully it's not the cartridge.
Turntable is still turning freely. I
don't know how what kind of shape that
idler wheel's in, but
we'll see. So, uh, I'm gonna I can't
stand it anymore. I'm going to wipe off
some of that dust, and then we'll turn
it around and look at the back of it.
Well, kind of antilimatic.
There's not much on the back. I guess
this is a
uh a line out.
Uh, it looks like we're maybe looking at
a couple tubes here.
Speaker on the side, volume knob on the
side. Like I said, I haven't used this
in 15 years, so
but we're going to be lo using it soon.
Um, okay. Let's tip it up and look at
the bottom of it.
Model number 360, serial number 30140.
Looks like there's a screw missing from
there.
Speaker over here. Speaker over there. I
do see some tubes. And then
folks, I didn't do that. It must have
been like that when I bought it. I would
have never done that. So, we got to
We'll probably have to put a new cord on
it.
Or if this one's long enough, we might
be the old Oh, yeah. We can do the old
Yes, we got that. Look how long. We
don't need all that.
Yeah,
we'll do the old, you know, the old put
her in the You know what I'm talking
about. Y'all have done all that. Okay.
Um H.
It kind of looks like you can pull the
whole thing out from there. I don't
know. What do you think?
So, let's attempt that. I'll lay it back
down flat and then if we if that is the
amp, we might be able to pull the whole
thing out. Well, it's just a little
grill. You can't take the whole amp out
like that, but you can get to the tube.
So, they're just doing that so that you
can easily service the tubes. Um,
so
I guess we've got other screws we have
to take apart. I would suppose that the
whole bottom can come out or something
so we can get to everything. We kind of
need to oil the turntable and stuff
anyways. So, so let's go ahead and take
it apart further.
All right. So, the turntable came right
out. It wasn't even screwed down. It
just lifts right up.
So, this is what we've got going on.
So, it's stereo, which is probably why
they called it the 360
speaker there. It'd be interesting if
all the speakers were working. I don't I
don't know if uh
I had all of them both of them working
or not. I probably didn't pay much
attention.
Here is our schematics. That's cool. I
like that.
I wonder if that just
mounted down there or where did that go?
like that.
I don't know.
It It feels weird, too.
It's almost like u
It's not paper.
I mean, I guess it is paper, but it
doesn't feel like paper. It's like um
I don't know. I don't know what that
would be.
Okay. Um, there's the filter cap right
there.
Is that the wire disintegrating?
No, it's just something on the wire. I
don't know what it is, but now it's on
my hands. That's fun.
Okay. So, that's the jack we were
talking about.
So, actually that's not a filter cap.
That's just a uh
H.
Well, the amp goes to here
and then uh
the yellow and the white wires
connect over to the jack. And there is a
cap on one of them. Probably to get rid
of the bass maybe
because uh it's for headphones.
Okay. And down here you have
a power switch and I suppose a volume
control
and mold and a bunch of stuff.
Can we tell
where that little
piece of paper was?
H I don't know.
Maybe it was on the bottom of the
turntable.
I'm just wondering so we can just put it
back where it goes, but I don't see it.
Okay. So, next
I am going to
I hope the
plugs for the speakers disconnect.
That'd be cool.
Or actually, maybe we can just do it in
place. Or I don't know. I guess we could
just turn it up. Okay. So, I'm going to
take these screws loose next so we can
see underneath the amp. All right. Got
the screws out. Let me show you
something cool before I do that.
I had uh the only quarterinch nut driver
I had was just a cheapo from China. On
some of my previous videos, I was
lamenting how I just had the cheapo from
China. So, I bought this at the flea
market the other day for0 50s. Let's
just check it out.
It's a quarter inch. Made by Fuller
USA. I like it. Number 211. I've never
heard of Fuller, but you know, it's
nothing really special. It's just a
plastic screwdriver,
but I kind of wanted one. I was
thinking, you know, all this stuff was
made in USA. It's all vintage. It'd be
kind of cool to have, you know, a tool
made in USA.
What have we here?
Filter cap. One, two, three, four, five,
six. I spy with my little eye. Seven
capacitors
and a filter cap.
What do you think?
Okay. So, yeah, I'm going to try to get
this loose. Or maybe it's already loose.
Oh, yeah. It's already loose.
Let's see if I can turn it without
ripping anything loose.
Looks like there's enough play and
everything.
There we go. That's what we wanted.
All right. So, now we can get to it
pretty easily.
[Music]
Filter cap.
One, two, three, four, five, six, seven
other capacitors. You know what I think?
I think the rectifier tube's going to be
bad. That's what I think. But we're
gonna recap it because I want to make
this thing rock steady, baby, so we can
um keep it for a long time and play it a
lot. I want to play it forever.
Um
and I know some of you are going to be
like, "Oh, just leave the caps." You
know, I'm not going to leave the caps.
I'm going to replace the caps.
Red, yellow, blue, black. Where are they
going to?
So, the filter cap is there.
I'm just tracking down wires here.
I think I might be able to get away with
uh
using what's already in there to mount
the electrolytics for this.
This hasn't been plugged in in many,
many years,
so we don't have to worry about getting
shocked or anything.
Well, we've lost our screw.
Some of you would say that that happened
a long time ago.
I kind of just want to see where those
wires go.
All right. So, yellow is here.
Red is here,
blue
is
here,
and black
is
here.
Yeah, we could just fly them. I'm just
going to We'll see if we if
Okay. Yeah. So, black
is also
that we'll have to double triple
quadruple, but it's also this blue wire
here.
And it's also this blue wire.
Looks like it might be way over here,
but we'll track it down. I'm I like to
just mount them, you know, you got to
get them where they're physically fine,
but I like I don't like putting in extra
strips if I can help it. I like just
mounting it, you know, and I understand
that
really they should all kind of be in a
similar position to where it was
originally, but
as long as it's electrically in the same
position that it was originally. I'm
cool with it. This thing's starting to
go for real, though, isn't it? What do
you think? Was that my problem? If I
remember correctly, the problem wasn't
the turntable. it was that you just it
wasn't amplified anymore
or it wouldn't turn on or something. So,
I I I
think it's going to it might be this,
but I think it's going to end up being
the u
um the rectifier tube. That's just my
guess. I've had about
three different tube
uh pieces of tube equipment that the
rectifier tube was bad on.
So, that's my guess. That's what I'm
going to go with. All right. So, I'm
going to go ahead and change some of
these caps and we'll go from there. All
right. So, I'm going through and
replacing capacitors. There were three
over here and two here that I've done so
far.
And I'm checking the resistors as I go.
This one here is 4.3K, 4,300.
It's measuring 4500. So that's fine.
That's within spec. You know, I'm trying
to stay within maybe 20% at most.
Hopefully not quite that. This one here
is a little worse. This resistor here
that you're seeing under my finger is
supposed to be a 10 meg, but it's a
13meg. So, it's a little out.
It's this one right here.
So, it's on
And you know,
I can't even tell what's going on with
this 128x7. I guess this has two sides
to it.
So, it's on the
input of one side. Is that the input? I
guess that's the input.
the the grid
and it connects it to ground, electrical
ground.
Not to be confused with chassis ground.
That's right, folks.
This cap goes, your chassis is hot.
Um, so yeah, that should be 10 meg. It's
13 meg. So that's not crazy, but it's
out of spec. So we'll see. how it
sounds, I guess, whenever we're done.
And if it sounds pretty good, we won't
worry about it. But I'll keep it in
mind. All right. So, I got them done.
Now, that plate mounts over here, you
know, so everything's got to be
contained in it. The clocks are the
clocks are telling us it's half past. Um
so
all new caps for the electrolytic or the
not the electrolytics the um uh wax you
know the paper caps safety cap to
connect the uh chassis ground to
electrical ground. Now, there was one
from here to here, but this is just the
frame, you know. So, I just since this
one was axial, I just went from here to
here, which is the same thing cuz that's
electrically
the chassis.
Um, and then there you have the three
electrolytics that were in the big can.
One was a 20, one was a 40, one was an
80. So, I went with 22, 47, 100. bumped
it up a little bit.
So, the one is right here. So, the the
black wire from it was connecting to
here. So, the ground for this one is
here. And then the other wire went down
there. None of that's touching anything.
It looks like it is, but it's nowhere
near anything. Okay. And now, and then
the next one was uh the 40. So, it's
this one. There's actually I put some
spaghetti on it, so it connects over to
here. Now, that was where all of the it
was where the black wire was. Um, but,
you know, we've got them in three
different spots. So, you could
leave the wires on it.
So, you know, I could have left the
wires where they were and cut them all
off down here
and then remotely mounted them on
another
one of these, maybe over here somewhere.
But, I didn't want to do that.
So, um, there is a blue wire that
connects from here to here and then back
around to here. So, I have connected the
ground of this to there instead of to
there. Now, it's not the best way to do
it. You really, you should have them all
ganged together, but on the schematics,
it's not even like that.
Let's see. Or maybe it is on this one.
Uh, two of them basically have their
grounds. You know, this doesn't really,
this is an electrical schematic, not
really a physical schematic, but you get
my point. It is better to have all of
the grounds going to the exact same
spot, but
the way these are wired from point to
point, it's just that's just not how
they do it, you know? So, it's it's got
uh since this loops the ground around to
a couple different spots, you can attach
those caps to those spots. in my
opinion. Now, would Mr. Carlson do that?
Probably not, but he's doing a lot
higherend stuff than I am. So, um I I
completely concede that he's doing a
better job. How's that? Um and then, uh
the last one,
uh we've attached to the same ground and
then uh it attaches to right here. So,
one went here, one went here, and one
went here. So, they're all in there.
I like it. And I added the safety cap
and took out just the regular one. Um,
now, who knows if anything was even
wrong with any of the caps. It sure
looks like this one was fatigued to the
point where it was ready to be replaced.
Okay, so um I think next step is I'm
going to clean this out a little bit.
Just vacuum it out, get it decent, and
then I'm going to pull the four tubes
and test them in a tube tester. My whole
hypothesis is the thing stopped because
the uh rectifier tube screwed up, but I
don't know. We'll see. Before we do
that, we've got to fix the cord. I
forgot about that. The cord's in good
shape. It just has this splice in it
with uh
priority mail tape.
Um I didn't do this.
Now, a previous version of me might have
done this, but I don't think so. Maybe.
I don't remember doing it.
But like I said, when I I've got this a
long time ago, and I didn't know much
about electronics then. So, there is a
little grommet that goes on it that
we're going to put back on it. Um, it's
this little thing. So, you wrap this
around the wire and then you put this
next to it. You squeeze it together and
you push it down through the the uh hole
in the uh power supply
in the amp. And uh then you've got a
brand new cord. I would replace it. I've
got plenty of them, but this is the
original cord and there's nothing wrong
with it. It's and it's really long, so
it's not going to hurt it to cut off a
foot of it.
So, I have out my trusty BNK Precision
model 747B
tube tester,
and we are going to test the 12 AX7
first because I'd already pulled that
out because I was looking at the socket
trying to figure some stuff out. Let's
see what we got.
Ah, that's good.
Good enough.
And then the other side.
That's kind of confusing. So, the first
three need to go down.
A B
F
E C.
All right.
So for the second side,
I don't like that. I got something
wrong.
What did I do wrong?
12 AX7.
Heater 12, sensitivity 89,
FE and C should be turned I mean the
first three should be turned off.
They are.
Then it should be A, B, F, A,
B,
F.
Then it should be E and C
E C off. Off off A.
And it should be test button one. I
wonder if that's a typo.
I don't know. See, this one is also both
of them are test button one. I don't
know.
Yeah, we got nothing on that.
Maybe we got a bad connection in the
socket.
Yeah, that was it. Bad connection in the
socket.
All right. So, both sides of that seem
to test well. So, this is interesting.
Uh, it has a 50
L6 GT in it and a
35 L6 GT, but I'm pretty sure the
schematics said that they should both be
35 L6 GTs.
Yeah, we'll have to look at that. Yeah.
So,
supposed to be two 35 L6s.
There's our 12 AX7 that we just tested
and the two 35 L6s which
um
isn't that called a pushpull?
See, it's not in stereo. See the
speaker?
Yeah. Isn't that called a pushpull amp?
If one of them is a 50 L6 and one of
them's a 35 L6, wouldn't that affect
how all the voltages are running
H?
Yeah, the numbers wouldn't add up right
because you 35 35 and 35 is 105 and then
12 is 117. So, they've got it wired for
117. And then also, if you look here,
they have a resistor across V1,
uh, which I'm not completely sure
the deal with that, but they also have
this resistor at the end of the string.
They may all have that though.
So, my whole point is you you don't have
enough voltage to run all those
properly. It's probably lowering all of
them.
So, I need to see if I've got a 35 L6.
All right. Well, let's test the two that
were in there, including the 50 L6. And
then, um, I may have a 35 I can swap in
to replace it. I would assume I do. I've
got a whole bunch of tubes.
But you know what happens when you
assume.
All right. So this is the 35 L6
test. Good. So let's for just for
giggles.
Let's see what happens.
So basically, if you put the 50 in,
it's going to lower the voltage just a
little bit going to every tube. So I'm
going to put the 50 in with it set to
35.
Now, it would get more than that in the
radio.
It would all add up to one, whatever it
would be, an extra 15.
Um, so what did we say it was? It was
105. So it's 117,
but we don't know what that resistor is
doing.
So 117 and um then we're adding an extra
15. So 132, but the line voltage is like
123 or something like that. So it's
going to reduce everything by about 10%.
Um so the ones that that want 12 volts
are only going to get 11 volts. The ones
that want 35 volts are only going to get
32 volts and the one that wants 50 volts
is only going to get like
uh 45 volts. So, I've got it set on 35
right now. So, it's not going to work
like that. But, let's just see if it
does anything.
Yeah, works just fine.
All right. Now, let's put it up to 50.
See if she'll glow. She wasn't glowing
really at 35.
I'm still going to swap it out though
because I think they ought to be
balanced, shouldn't they? Since it's a
amp.
Boy, look at the glow now.
Okay, so that is 50 volts.
Much better tube. Yeah. Well, I think
that just proves that if we're if we put
that in
and it lowers the line voltage to every
one of the other tubes, there's only
three other ones, but if it lowers the
line voltage the other tubes, that
decreases the u the quality of the tube.
The tube's not going to work as well at
a lower filament voltage, obviously. I
mean, that's why they designed them like
that. So putting that one in, yeah, it
takes up the over voltage from the line
voltage going up. So it was designed for
117, but the wall voltage now is like
124, 123, 124, something like that. So
it's a little bit higher, but they're
kind of going overboard. And that's a 50
and that's a 35. So they're not
balanced. and it's it's literally
in a balanced
um design, you know. So, I don't want a
50 and a 35 in there. I want two
identical ones in there. So, let me see
if I can find a 35 L6.
All right. So, I actually did have
another even an RCA which matches this
other one. I don't know if RCA did all
the tubes for Colombia.
I don't know. I'm looking at the thing
here. I don't see any definite
relationship with them. Didn't RCA have
the patent though for
the way the amps were done or something.
Anyway,
so
it's good. It's not quite as good as the
other 35 and the 50 was much better, but
again, I think I'd rather have them
balanced. Okay, so now we get to test
the rectifier, which my theory was the
rectifier was the problem the entire
time. Well, it's probably fine. The only
time I've ever seen one of these
rectifiers bad was it was physically
broken inside or the um
the filaments broken.
So, let's test it.
Yep, it's fine. Um it could have been
sockets though or I don't know, maybe it
was a cap. Who knows?
The thing was completely dead though.
Hopefully it's not the pickup.
Remember that last time when we had the
pickup problem?
Okay, so next up is the actual record
changer. Boy, she's dusty.
Neutral 45 and 78. And no, I did not
have the wherewithal to leave it in
neutral, unfortunately.
Um on
off
and
uh reject
off. Okay. It's they're telling me this
is No,
I can't. Oh, yeah. No, I can't remember.
Okay. So, there is a knob there. See the
little dot? So, I think that's on.
There's a little bit of wiggle there,
which maybe that's the reject to get it
to go to the next record. I can't
remember.
And so this is just the speed of course.
33 45 neutral and 78.
Yeah. I don't remember how the reject
works.
Okay. And here's the flocking. I was
wondering when I was looking at this if
that was meant to be that groove. And
there is a ripple.
in the uh platter right there. There's
one right there, too. And it's not like
that. So, I wonder why that has that
groove in it.
So, was that cut by the needle at some
point?
I'd have to determine. Yeah, because
You know, that obviously was.
So, I wonder if
when you have a 45 on there, I wonder if
the needle misses the 45, does it cut
that groove? That's what's going on
there.
Okay. So, let's look at the pickup while
we're at it.
mono.
Yeah. See, that's I think that's a
ceramic pickup,
so hopefully it'll still work just fine.
And I apparently have had it set on 78.
I don't know if I was listening to 78s
before or what.
I'm sure it could use a new needle.
Titans, I believe it says
Titans.
So, just the typical flip over needle.
That'll be easy to find if I need one if
the if the uh cartridge is any good. And
here is the
stacker lever.
These both seem to be working as they
should.
I thought I had the insert, too. I might
have that laying around somewhere. If I
don't, I'll get one. Okay, let's look at
the bottom. All right, so the actual
changer, I don't see any grease that's
gked up on it, and it's actually moving
very free. I think I'll still oil
everything, but it doesn't look like
I've got to remove a bunch of grease or
anything.
So, that's it's just all that's doing as
it should.
Very cool. Um, now the motor is probably
fine, but I'm going to oil it. So, let's
just for giggles,
let me not put that in there. whatever
that was.
Yeah, it's still turning freely. Okay,
so I'm gonna uh take this bearing off
and oil it. And then um I think we may
be able to get to the other one from the
top
without having to disassemble the whole
thing. All right. So, I was able to get
that apart, but then I took it out too
off of the the mounts uh because I
wanted to
um basically these screws have a nut on
the end and so you kind of need access
to it. So, I took the whole thing off.
Uh the the uh motor mounts to me look to
be in pretty good condition. You can get
new ones of these that are generic. Um,
they're kind of all very similar, so
you can buy those really cheap, like a
dollar a piece or something like that.
And if you get a whole handful of them,
they'll work on all kinds of different
um record player motors. Okay, so I
still want to flip it. I was able to uh
put oil on the top as well, but I want
to work on the idler wheel next, and I
want to see if we've got a dent in it.
All right. So,
if I can get you in there where you can
see
here is, of course, the idler wheel.
All right. Let's see if there's a dent.
We're looking for dents in all the wrong
places.
I don't think that's a dent. I think
it's just some kind of
Yeah, I don't think there's a dent.
um
rubs against here and then the spindle.
This one actually works a little
different than they usually do.
It turns this directly.
I guess it's it works basically the
same. But
yeah, that's why there's no dent, isn't
it? It's just done different
since this is bigger.
Yeah, it presses up against it. I got it
in neutral right now, but yeah, it
presses up against it, but it's a bigger
circumference. So, I guess it's harder
for it to make a dent because the actual
spindle isn't touching it. And the
spindle also has a spring around it.
I've seen that before on some of them,
but only on one speed. This one does the
speeds different. It attaches a
different roller depending on the speed.
So, I'm going to use some rubber renew
on this and um
we'll see how that looks. And I'm about
ready to put it all together and see if
it'll work. Okay. Now, I want you to
think, if you're a regular viewer of my
channel, when have I ever told you that
something expensive was worth the money?
I never do, right? I am not the type. I
am not a believer. I do not
automatically just believe that, oh, you
got to use the expensive stuff.
Um, to me, if you can use something
cheap, use something cheap. That's how I
see it.
This stuff is fantastic.
It's a little more expensive. I think
this bottle is like $25 or $30, so it's
not crazy expensive, but it's still a
little expensive. Um, you don't really
use that much, you know? So, what it
does is it just makes rubber like rubber
again. Like you saw that just now how
that looked. It was all dried out
looking and everything and it felt
really hard to the touch. Well, I just
rubbed that on there
and now it feels like rubber again. So,
I don't know what it does, but it seems
to work pretty good.
So, it basically just
it just makes it and now it's not going
to do a miracle or anything,
but
it just makes it work. I mean, it just
makes it nice again. All right, so I'm
going to show you how they did the
changer on I mean, not the changer, but
the speed on this one. So, that's 78
right there. You'll get the you'll get
the point here in a second.
45
neutral
33
or did I go backwards? I went backwards.
78
neutral
45 and then 33.
just a little different um way of doing
the same thing.
And you can you can just see because the
spindle is so thick, it's not going to
make a bump, I don't believe. I put the
rubber renew on that stuff, too. What am
I seeing on that one there, though?
Oh, I'm seeing a reflection. That's what
I'm seeing. Okay, I'mma plug it back in.
I'mma wipe it down a little bit. plug it
back in and we'll see if we can get any
kind of amplification.
Okay, so first thing I'm going to do is
just plug it in. I don't think it'll do
anything without the uh turntable turned
in because turned on because the onoff
switch is on the turntable,
but I didn't uh let's Well, hell, let's
just look. We got to do a smoke test.
And I hate to cover it all up.
There's the power.
Yeah, look, it's it's powered up. The
switch is just for the motor.
I guess
it's auxiliary jack.
Yeah, look. Motor and switch.
Well, that's a little scary. Um, is this
thing turned on? No, it's not. Okay.
Yeah, I'm I'm looking at it wrong. Okay.
So, see where it says socket rear view?
I'm holding it with both hands. I can't
show. Well, yeah, I can. Let me lay
down. I'm reading it wrong.
Here's the line going in. And one of
them goes to this jack, which goes to
here, which runs through the switch.
And then after it's turned on, runs back
through here. So without the without the
record changer assembly plugged in,
you're getting no power to anything. So
you're just wasting your time. I guess I
could rig it up, but we're going to do
it blind. Why not? If smoke comes
rolling out, we'll unplug it. All right,
folks. We're looking for smoke. I didn't
wipe it down yet, but we're looking for
smoke, and we may get it. Let's see. We
didn't even test the voltages or
anything, remember?
All right, we're plugged in, but the
switch is off.
The tubes are on the back at the bottom.
But if there's a problem, we'll see it
over here.
It'll come up and hit the plate and then
find holes to get out. And we'll see it
start doing this. Um, I have the fire
extinguisher ready and I'm dead serious.
All right, I'm going to turn it on. Now,
I don't have the turntable on because
there is a little note here that says,
"Be sure change cycle is complete before
turntable is replaced." And that can
slide right on. So, I wanted to make
sure that
it's where it's supposed to be before I
drop that on there. All right. So, I'm
going to turn it on. That's going to
power up everything. We might get a
kaboom.
I also um sprayed contact cleaner in the
tone and volume knobs. So, I'm going to
turn up the volume knob.
Oh, yeah.
Hear it amplifying that that beautiful
motor noise. So, we're dip back down.
Back up. All right. So, I'm going to
touch the pickup.
[Music]
Sounds amplified to me, people.
Very cool. Well, I'm glad to have this
thing back with us.
Um,
let me carefully put the turntable back
on and let me get a um
let me see if I can find a 33 that it's
not going to give us a copyright strike
on.
All right, the changer still needs some
work. It's hanging at some point in it
like it's, you know, going through its
cycle. It's supposed to move the arm
back a little bit, which it did.
Drops it.
Really? All right. So, I've got a This
is an RCA 45 adapter. I think RCA and
Colombia were in cahoots. Um, and this
it's working, but it's it's that changer
is dragging. So, I don't I don't have
something greased or oiled right yet.
So, we'll see what she does.
I think I just barely turned it on
and turn it a little more and it tells
it to drop it. So, it hangs a little
bit. Hangs a little bit. Dropped one
record.
[Music]
And it gets really good volume. really
good volume. All right, so uh
I'll cut this because the next one will
have to be for u Patreon because they're
definitely going to copyright strike the
next one.
All right, folks. I need to clean it up
a little bit more. Um
I'm happy to get this thing working
again. I' It's been broke a long time
and I'm I I used to listen to this all
the time. I mean, all the time. I've
spent many hours listening to this while
I was doing other things. Um, and I
think uh with the cap job, I think I got
it'll last me a long time to come. I
need to I'm going to order a new needle
um immediately. So, I've got those. I'll
just probably order a couple of them
since I know I'm going to keep this
thing. Um,
but yeah, really cool. I'm really happy
with this. Now, the changer, the way it
slows down like that, something's
hanging a little bit. It needs a little
grease or something somewhere. So, I'll
keep messing with that. I'm going to
play it a little bit and see if it just
frees up and works its way out. And if
not, it's really easy to lift up this um
the change the changer unit. I mean, you
can just pick it right up. Nothing uh
holds it in there. It's sitting on
springs. Um and I'll just keep oiling
the heck out of it until it it changes
really well. So, I hope you enjoyed it.
Leave your comments down below. That I
just played uh Sam Cook and um I'm going
to put that up on our Patreon channel.
If you don't know about that,
YouTube,
one of the things they do is uh they
block your video if it has certain songs
in it. So, when I was playing that one,
they probably don't know what that song
is because it probably wasn't a big hit.
So, you got to hear a little bit of
that. Um unless it was cut out, too. If
it was, I had to edit it out. But, um if
they'll let me put that in, I'll put
that in there. But, they're sure as heck
not going to let you play Sam Cook. Um,
but so what I do is I just filmed a
little segment of that playing so you
could hear it and I uploaded it to our
Patreon account. There's a link down
below if you want to check that out. And
then we also put on there uh little
snippets of our videos where we're
showing a little just one little thing
and um to make it a little more
accessible where it's just a little
twominute clip of uh something that we
did that's hidden in the middle of these
hourlong YouTube videos. And um uh
sometimes on there we'll put stuff
that's just a little clip of something
that uh doesn't really make for a
YouTube video, but it's just a little
short thing that somebody might find
interesting. So if you're interested in
any of that, the link is down below, but
we will see you on the next one. Tell me
what you think of this uh this Colombia
360. Would this be good enough for your
home? It's good enough for mine.
All right, folks. So there's where it
will live.
And uh I Put a little bit of this on it.
Howard feeding wax. This stuff is great.
It's like bees honey type stuff. And uh
it puts just a little shine on it. Makes
the
finish look much better.
Beautiful.
All right. So, if you enjoyed that and
you like these old record players, I've
got several of them here on the channel
that I've done. Check out this video.
