Check Out Our Patreon Account, for Unreleased Repair FAILS, Concise Repair Tips Not Possible In This Long Form Video, And 1 on 1 Repair Assistance with YOUR Project!
Thank you to everyone who has been supporting our channel! If you use the link below before you purchase anything on Amazon, we get a royalty for sending you there, thank you!
Our store is located at 139 Caldwell St., Rock Hill, SC 29730.
Ladies and gentlemen, this is Joe's
Classic Video Games back with yet
another pinball repair video for you
this evening.
I guess I should say another cool
pinball repair video for you this
evening. We've been working on this
supersonic for forever.
And uh we've got some stuff left to do.
So, we did a whole bunch of videos on
the playfield. Finally got it doing its
thing, but we haven't actually played
it. We repainted a bunch of it. If you
didn't see all those videos, check it
out. We had to order a few parts. Um,
basically our flippers need work.
The drop targets clearly need work.
And the pop bumpers need work. What's
going on with this? So, I think the
first thing we'll do is put in the new
uh pop bumper caps. We ordered some
stuff from Marco Specialties.
It came in and so uh we'll check that
out. So, it looks like at one point one
of the caps must have burnt up or
something in this. So, they ordered one
for it, but they ordered the wrong one.
That's not how it's supposed to look.
The roof on the flyer, they're all like
this. So, I could have just ordered the
one
cuz the other two are perfectly fine.
But then they look worn, you know? I
wish I had one more worn one. I I looked
all over. I couldn't find it though. But
you know what? I've got
I've got an extra worn one now. I've got
two extra worn ones. So, I'll just swap
this out and save these two and down the
road I'll probably end up with a uh
machine that might need one or
something. Um,
but we got to put three of them on. I
honestly think the old ones look better.
The new ones are just so bright that it
you can kind of tell that they're brand
new. I don't like that. Um, the same
reason I left these up here. They're not
broke.
I'd like to keep them, but to each his
own. So, I'll swap those three out. I've
got it in lamp test um just to make sure
they're all working before we lock the
bulb up inside the cap.
Much nicer. They look great. Okay, so
I've got the light test on. All of the
lights are working except for that one.
The left special has been giving us
problems.
And if you didn't watch the earlier
videos, this thing had all of the boards
fried in it. Every one of them didn't
work. and we did a repair on every one
of them except for one. Um, and we did
the lamp board, but I didn't get that
bulb working. So, I've tinkered with the
socket. I've put the bulb in it and
everything, but it's definitely
something uh either on the connector or
the board or something. So, that's what
we're going to figure out next. That one
stray light bulb. So, like I said, I'd
already I've already messed with the
socket um and swapped the bulb and
everything. I know it's not that. You
can actually check the voltage on the
the socket and see if you've got voltage
there. You can check back the voltage on
the pin. See if you got voltage there.
And uh you could do this on the on the
lamps. You don't really want to do it on
the displays, but while the game is on,
you can kind of manipulate one wire.
Like I'm pulling one wire in and out.
That'll kind of like if you track down
the actual
bulb wire, you can kind of fiddle with
it and it'll kind of tell you if it's
the connector. Typically, I usually
don't have a ton of problems with the
connector on the lamp board. Now, you
have a ton of problems with the
connector on the power board because of
the battery damage over there. You see,
we've actually replaced that one. Um,
but I kind of already knew what the
problem was. If you look on the
schematics, the transistor that runs
that bulb is Q46.
It's called the left outline on the
schematic.
And we did an entire video where we
messed with this board and um got all
the lamps working. Well, on that video,
we ended up having to replace two
of the decoder chips,
which are MC14514
chips.
You can see the date code there is the
21st week of 1979. So I mean these
things are ancient ancient.
So two of them we had already replaced
and this is why. So this third one here
look at the rust on it.
Right? So I had already made a list of
all of them and I'd already replaced
that Q46 and everything. Um, and then we
replaced these two and we got every bulb
back except for that one bulb. And sure
enough,
it was the decoder chip. So, one of the
lines on the decoder chip, just enough
to make it where you can't leave it. One
line was bad.
And it's just a it's a rust thing.
Whenever you see surface rust like this
on a chip,
that's pretty bad.
So when you see that, it's likely inside
of the casing, too. The metal as it, you
know, that that leg just goes inside
here and, you know, creates a pattern
where it's connected to other things.
But you've probably got that same rust
inside. It creeps in.
And uh apparently that was the deal. So
I swapped in
a third decoder chip and this board
didn't have any uh battery damage on it.
The battery sits right here and so a lot
of times it will out gas or leak all
over this part of the board and screw it
up. This board was really clean if you
watch that video. Um but we had tons of
lamps out because of this chip, tons of
lamp out because of this chip, and then
only one that was controlled by this
chip. So I thought, "Oh, hopefully it's
just the transistor." I swapped it twice
just to make sure. Uh, but that wasn't
it. So,
now we have every lamp on the game
working. I'm very happy about that. Let
me make sure I didn't mess any of them
up on the back box.
Sometimes whenever you swap, look at
this.
I didn't swap that bulb yet, though.
I hope it's that. If it's not that I'm
gonna be so angry if it's If it's not
the Oh, man. I hope it's that. Ah, it's
just the It's just the bulb. It's It's
And this one, too. That one was It's
just the bulb. There wasn't like a You
know, there wasn't like the the board
that caught on fire. It It was the bulb.
It's just the bulb. No big deal. They
come right out. You put in It's no
problems. We got it. All the All the
bulbs.
All the bulbs are working. It's great. I
love it.
All right. Well, it may seem like I'm
jumping around, but actually I'm not.
And the green ones are working, folks.
You just can't see them that good. Don't
worry about it. It's working. It You
just can't see it that good. The uh It
may seem like I'm jumping around a
little bit, but I'm not. I'm You know,
this is the I'm trying to do everything
on the playfield. So, next up are these
drop targets. They look like someone
that needs dental work, right? It just I
don't What in the hell? I think one's
missing and at least one's broke. It's
broke. Joe's not here to tell us that.
So, uh, we need to figure out how we can
slide some new drop targets in there. I
ordered some brand new ones so it'll
look nice and snazzy. Um, but we got to
get the old ones out first.
So, yeah, it's a mess.
So, one of them is missing
and the spring is missing that holds it
on.
This one's there,
but it's just a blank one. It's supposed
to be a little bullseye.
This one's there,
but it says
2X.
It's not supposed to say 2X. It's
supposed to be a bull. It's supposed to
be a bullseye, people. This one's there,
but it's clearly a kapow. And you don't
want the kapow. You want the bullseye.
And I don't think it's broke. Well,
yeah, it's broke. I was about to say I
think it's just unhooked, but the reason
it's unhooked is because it's broke. So,
the kapow went kaput. And then this
one's there.
Uh, and it is a bullseye. So, this is
maybe one of the original ones. It's
that bottom one. So, that tells you
right there that that bottom one must be
hard as hell to hit. So, we're going to
have a problem hitting that bottom one
for show. You can see all the pretty
bulbs working. Um,
so you can do this actually while it's
mounted in the game. So, first thing I'm
going to do is take these screws off.
So, there's four screws on this little
bottom plate.
All right. So, once you do that, you can
pull this plunger actually all the way
out. Just don't forget to put it back in
there when you put that plate back on.
Um, and let's see if these are going to
cooperate enough.
Probably not.
Yeah. So, the issue is
the target.
It's kind of hard to show.
It's kind of catching on that lip up at
the top because it has to go out through
the top. So, you can't you can't pull it
down through the bottom of the machine
after you take it loose. There's just
not enough room to maneuver this out of
that and get it all out. Um, so the way
you fix that is you take this back plate
loose. You don't have to take it all the
way off, but you got to loosen it up.
Um, and you really shouldn't do that
with the lights on. So, what I'm going
to do is there's a screw here and a
screw here. And if I take just those two
loose, this plate will move a little bit
to where I can finagle it out. All
right. All right. So, with those two
loose, I can move it enough to where
these will pop loose. And I hate this
crap. Look at this. At some point, they
removed that drop target or it broke.
And then they took the little bolt off
that I need and lost it. Why would you
not just put it right back where you got
it?
What are you doing, people? They're
parting them out and I'm parting them
back in. It It's It's just craziness to
me. What are they doing? Did they really
need that damn bolt? Come on.
Come on now. Drives me crazy.
Luckily, I have parts where other people
have parted them out. I didn't part them
out. All right. Other people parted them
out. I just ended up with them. All
right. So, I was able to find a
replacement one. And I actually keep the
springs in new. You can order those
little things I'm talking about new,
too. But what's Come on, people. What
are they doing? It didn't break. There
ain't no way it
I'm going to stop.
Look how the new uh drop targets bend.
They're very bendy. I think they do that
so that they don't snap as easy. That's
my story and I'm sticking to it. Okay.
So, now it's just a the matter of lining
up each one with its spring and putting
the little bolt back in it and sliding
it into where it goes. And then you have
to line that lever up with the little
slot in the plate because that's what
hits the switch on the back and just put
it all back together.
So, this is why I hate reproduction
stuff.
I would much rather just use the
original stuff if I can do it. But on
drop targets, you can't. So, you have to
get reproductions
and
Yeah.
All right. So, the next thing we need to
figure out is what to do about the
flippers. This one is actually fine.
Needs cleaned up a little better and
it's a little faded, but this one's all
cracked up. So, we got to do something
about that. And then the flippers may
need work or something. We have never
flipped them, I don't believe.
Um, I don't think we've tested any of
the solenoids anywhere on the playfield.
So, uh, let me see if I've got a
similarly yellowed flipper bat or if
I've got two new flipper bats, flipper
shoes, I guess. So, uh, that's next.
All right. I didn't have new ones, but I
did find a used one that looks exactly
like the one on the right. I wish my
drop targets looked like Look, I'm just
I'm trying to get over it, folks. I'm
just trying to get over it. All right,
so next thing to get over is I didn't
even notice this at first. One of our
astute commenters pointed it out. These
cheaters have cheated
with this uh this uh gate thing here.
Look how they cheat.
They put it behind the nail
to cheat.
I wonder if the nail will easily come
out.
Yeah, not really.
Well,
how do we want to do it? I guess we'll
just take the we'll take the post out.
Oh, nope. Never mind. I think I can just
kind of hop it. Oh, I jumped the border.
There we go.
Okay, we'll have to watch and see if
that actually works. We probably need to
oil it. There's a little Let me show you
the little thing under it that runs it.
So, there's this little bit of genius.
It's just a coil that can pull in and
when it pulls in, it will open the gate.
And so the way they do it
is when it pulls in,
it moves that little bar there. So the
problem that you end up with on these
is that this spring is what pulls it
back out.
And so if you get any kind of dirt or
wear or anything on this, it does this.
It sticks in and then it stays like that
whenever it lets go. Like right now, it
is not electrically pulled in because
the power's off. The gate's stuck open
and not in the cheating way with the
nail. Um,
so a little bit of oil should fix that
for us.
Or you know what? It's in a nylon
bushing, a nylon sleeve.
I wonder if gravity has anything to do
with it. We've got the place upside down
right now.
Yeah, part of it is.
Yeah, it's gravity. Maybe not. I don't
know. It might be gravity, folks. We'll
see.
We'll watch that. We need that gate to
close uh reliably.
Uh,
now the
flippers. I have cleaned the end of
stroke switches. I don't know if we need
new
flipper plungers yet, but we'll try it a
little bit and see. That's coming up.
All right, while we're in here, we need
to We didn't replace this yet either,
the shooter tip. So, we'll go ahead and
put a new one of those on, and then
we'll see what other trouble we can get
into. Much better. Now, another thing
that is a problem
is this.
A lot of times if something breaks,
you'll actually find it in the machine
cuz I mean, where else is it going to
go?
So, what is this? This is the little
kicker thing for the
It's the kicker thing for the kickers.
So, when the ball hits that ring,
it closes one of those two sets of
switches, either that one or that one.
And then the computer tells it to kick
the spring. And so, there's a little
metal blade that comes forward and it
hits the spring. And you can see the
plastic piece there.
The one on this side
is missing.
because I have it in my hand. It fell
down inside the cabinet.
So, what do you do about that? Well, we
got to fix it. We're not going to leave
it like Come on, people. We're not going
to leave it like that. Come on now. All
right. So, I think the easiest way to do
it would be Well, damn.
H
Well, we're going to do it from the top.
Let's do it from the top. All right. So,
I took off the the shield, the things,
and the ring. And you can see the
problem.
It's gone.
It was supposed to be like that.
But the problem with replacing it is
that little pin
you have to get out. So I don't know if
I can do that while it's in the game or
not. But we'll try. So I'm just going to
try to grab it with a pair of pliers and
see if I can pull it out. What do you
think about that? Keep in mind I've got
a whole bunch of these as spare parts if
I end up mauling it.
All right. So using a pair of pliers.
Let's see if these are the Chinese ones.
Yep, the Chinese ones got the job done.
Using a pair of pliers, I just kind of
grabbed it a little bit, you know, a
little crooked and pushed it to the end
and then was able to just pull it out.
So, the little actual
piece here,
um, I've got a whole bunch of these new
old stock that I got somewhere.
I may have got these from Shane
if Shane's watching. Thanks, Shane.
Can't remember. So, they're all very
similar. So, you just pop one on. I
wonder if it's exact.
It does look pretty exact.
What do you think?
All right. So, now I got to try to put
the the the uh pin back in, which ought
to be easier by because you could just
beat on it, right? I mean, I could just
I'll see what I can do.
All right. So, I actually was able to
just squeeze the pin back in there with
the pliers. So, you can do that
um by hand with a pair of pliers if
you're
patient.
All right, let me put it back together.
One last thing.
All right, so we got that back together.
I think it's all good. This one over
here is kind of bent,
you know, and they do that a lot, but
this one's a little excessive. So, I'm
going to pop it off and show you how you
can fix that real easy.
All right, so it is all puffed up. I've
got a heat gun.
As the heat hits it, it'll actually get
worse a little bit.
And I'm moving the gun around. You don't
want to be in one spot too long.
And when you see it start kind of
relaxing a little bit, you're about
done. You don't have to go, you don't
have to make it all the way flat. Like
right now, see how it's starting to move
down a Okay, there we go. See how it
started moving down a little bit.
I'm doing it with one hand. I might not
be quick enough.
All right. So, you want to put it on a
piece of paper, white paper, just
because it's smooth. Like, if I do it on
this desk, you'll get like a pattern in
it. Um, and then you just want to put
like a heavy book or something on top of
it. I've done it before where I uh use
glass out on our showcase.
So, you you can do that on the piece of
glass and then just drop a heavy piece
of glass on top of it to hold it in
place. Um, I just happen to have this
book sitting here, though. Check out
this sweet book.
So, it's the We're letting it uh cool
off a little bit right now. We'll see if
that was enough or if we need to do it
again. It's the National Association of
Watch and Clock Collectors
Bulletin. So, like each month they put
out like a little magazine. And you can
buy these. They're reprints. But this
particular one is kind of cool because
it's actually the actual issues
bound in a book. So you see it's got all
the covers and everything in there
instead of just being a reprint
um in a book.
So anyway,
you don't have to leave it long cuz it's
just cooling off. Let's see if that made
it flat or if we need to hit it some
more. I don't know. It kind of looks
like it's still puffed up a little bit,
doesn't it?
Well, it's certainly much better.
I'll do it again.
I probably should have done it on the
paper in the first place so I didn't
have to waste that time putting a piece
of paper down.
If you wait for it to go all the way
flat though, you're going to end up
scorching it a little bit. The edges
will get screwed up.
So, it's getting there now. Oh, yeah.
Now she's getting there.
All right. So, I think that will get it
and we'll put it back on the machine
after it cools off for a few minutes and
um that'll fix that problem. On to
whatever the next problem is. All right.
So, it looks a lot better. Flattened it
out.
If you let the light hit it, you can see
a little bit how it will it will damage
it a little bit if you have to do that.
See how down on this end the right
through there. It's got a little bit of
a texture to it.
Right.
But it looks a lot better than it did.
So, I'm cool with that. Okay. So, we are
ready to check the solenoids. We have
not done that yet. Um,
I'm a little worried about it because if
you didn't watch the earlier versions of
this video, there was a short on the MPU
and it shorted out every board in the
game and it was the 43 volt was shorted
to the 5VT. Um, by the way, the displays
are not actually doing that. It just
looks like it on the camera. So, I'm
going to go into test. Test number two
is the solenoid test. It's going to
cycle through them all and we'll just
see if any of them work.
The fuse on the playfield may be blown
too.
Lights.
Displays. Actually, that's number two.
So, none of the solenoids are working
except for the knocker, which is nuts.
And you're going to hear the flipper
relay in the back.
Hear that? Oh, that knocker's crazy. Oh,
Lord, that's crazy. All right, so why
would everything on the playfield not be
working?
I just remembered what the problem was,
but I'll just show you on the
schematics. I hit the flipper button and
the flippers didn't work either, which
is a dead sign that there's something
wrong in the back box because
if you look, this is actually your
voltage.
And the flippers are not fused.
The fuse for the flippers is essentially
the fuse in the power supply. So if
they're not working, that means that you
don't have your 43 volts on the
playfield. Some for some reason there is
a fuse on the playfield.
So after the voltage comes up and feeds
the flippers. This is the ground of the
flippers,
right? It moves on and goes to the out
hole and then the left, the right
bumper, the saucer, the right slingshot,
the left slingshot, the bottom bumper,
the gate relay, and the drop target
reset
uh coil. So, we don't have power here.
Usually, it's this fuse, but in this
instance, we don't have it here either.
I don't think I ever plugged the
solenoids back in because we were, like
I said, I was a little worried about it.
So, I've kind of been afraid to run it.
The flipper enable relay is on the
solenoid board. So, it doesn't need any
kind of wiring going to it other than
the voltage that's running the game. And
then the knocker um I believe is is
plugged in on the um same connector that
the test button is plugged into. So, I
plugged in that one because I needed it
for the test button. Yeah. So, here's
the test switch. It plugs into on the
back box A4 J31. So that's A4 is the MPU
and then the return or the ground of the
test switch plugs into A3 J27. A3 J27
um is the solenoid board which is so
that same A3
J2 is the same one uh that the flipper
switches
and
the knocker and the speaker.
No, not the speaker. and the knocker and
a couple things plug into. So, I've
already got that plugged in because I
knew I needed to plug it in to get the
test switch to work. So, I think if we
open the back box, it's just that
board's just going to have everything
unplugged from it. Sure enough. Well,
that makes it easy.
Two of the connectors were off.
All right. Coming soon. Um,
okay. So, that uh means that now we have
power on the playfield. We should we
should. So, what I'm going to do is I'm
going to turn it on. And we need to
watch this thing and make sure nothing
shorts on. We don't have a coil stuck, a
switch stuck. Uh, we don't have a
problem. So, I'm going to turn it on and
then turn it right back off if anything
locks on.
Okay, we should be good.
All right.
So, let's try again what we were doing.
Test one.
Test two. Here we go. Remember the
knocker is very loud.
Still nothing.
I'll show you the flipper enable relay.
Okay. So, what is the problem? Well, we
can tell if it's the playfield fuse by
whether or not the flippers work.
We may have just blown a fuse.
No, got it. Okay. So, we got flipper
issues. We'll have to figure out what's
going on with that. Ooh, did I mess up
with the
No, I did not. I can only go on that
one. Okay. Yeah. So, we got some kind of
we got some kind of issue on the
playfield. Let's see if we can figure it
out. All right. So, the power is turned
off. Now, here is that fuse.
She's blown. But why aren't the flippers
working? Well, sometimes um you've got a
bad solder joint on the actual flipper
coil. It's actually very common. If you
saw how in the schematics, the first
thing that the power does is it comes up
to the flippers. So,
if you uh have a really bad solder joint
on the flippers, and these don't look
great, to be honest, that could be the
problem. Uh, it could be that you've got
really dirty end of stroke switches and
it could be that you've got really dirty
cabinet switches, which I think that
might be the issue.
Like, can can voltage get through there
enough to pull in a coil?
Maybe not. So, I'm going to clean those
up with a file. We're going to replace
the fuse. I'll look on the schematics to
see what it's supposed to be. I think
it's supposed to be a 1 amp. And, uh,
we'll try it again.
So, there's the knocker. Yeah, these
were filthy. So, I think that might have
been it. I put the fuse back in. Let's
try it again. So, same thing. We're just
we're checking to see if anything
catches on. If you catch it quick
enough, it won't mess up your board. You
won't even blow the fuse if you catch it
quick enough. Um, so as you're turning
on, this is on an unknown game, you
know, as you turn it on, just see if
anything locks on immediately. It'll do
it as soon as you can put power on it.
If it does, turn it right back off.
It's actually kind of scary whenever
whenever you see that because it's so
violent.
Okay, now that it was supposed to do it
was doing that at the end of the uh the
boot up and it probably would have
played some music and uh I think we just
showed that the coils must be working
now. Okay, so let's go back into the
test and just see if it works through
it. Sometimes you'll have an issue where
the coils are working except for one of
them and whenever it fires it blows the
fuse.
I I just like to be, you know, this is
an unknown game. I just like to go
through it systematically where you know
every little thing about it. You know
all the little quirks. You find
everything is hiding from you.
Okay, here we go. And again, the knocker
will be even louder this time.
We're good. Got to test the flippers,
though.
Oh, you know what's going on?
Who can tell me what the problem is?
Here, I'll show you the problem. Right
flipper.
[Music]
All right.
Left flipper.
The flipper relay has to be on for the
flippers to work. Come on, Ronnie. Come
on. Come on. You should have known that
now. Why were you trying to hit the
flipper button when the flipper relay?
Well, come on now. You know the flipper
relay's got to be on for that. Come on
now, Ronnie. Come on. Come on now. The
flip the flipper relay's got to be on.
Come on now. That's not how it's
supposed to be. You know the flipper
relay has to be on. Come on now. You
gota You got to have the flipper relay
on.
All right, we're in number four, I
think, which I think is the sound test.
All right, so we're in switch test. So,
we're going just going to check all the
switches.
Right out lane, right in lane,
left in lane, left out lane. Now, you'll
notice the left in lane and the right
outlane are the same switch. Why not,
folks?
Why not recycle switches? Okay. Bottom
target, middle target, top target.
Okay. Spinner.
Okay. Bottom pop bumper.
Right pop bumper.
Left pop bumper.
Uh rollovers.
One.
Two,
three,
four,
five.
Top rollovers.
Five, four,
two,
five, three. Three bonus advance
rollover.
I said three bonus advance rollover.
That one's going to need a little work.
Um, saucer. This is always fun because
it wants to bite me. Oh, don't bite me.
Okay, that worked. Uh, what else do we
have here? The slings. I don't know that
it will do those.
I mean, clearly they're working.
32
26. Okay. Oh, there's rollovers in the
middle, too.
These rollovers are You got to get them
just right. So, one is not working.
Two is not working.
Three is not working.
Four is working.
Five is working. So, one, two, three,
and the top one. Okay. And then the
center target, it's working. All right.
So, now we got to do drop targets. These
are a little tricky because once the
target goes down, that number just stays
on. So, you can't tell, you know. So,
this is the bottom one.
One. So, the next one.
Yeah. So, see the one is stuck. So, I
got to bring it back up.
All right. So, now that it's back up,
two is down and it can tell.
So, if I drop three, it won't do
anything because two's down. And I want
you to notice two's down. This is
primitive stuff, folks. If you think
this is primitive, by the way, you
should see what Gotlib and uh Williams
were doing
at the time with their test menus.
Okay, there's three.
We'll just drop all of them.
Let's do the one behind it, too. It's
not going to work because I got three
down.
This is that
This is that great action you want in my
videos.
Four works.
Come on, you ugly little horrible
reproduction drop target.
Okay, five works. So, all the drop
targets work
shockingly,
even though they're are pale, pun
intended,
imitations of the originals.
Yeah. Okay. So, that's that. So, let's
see if the little rubber behind it
works. Yes. 13. Okay. So, the only thing
that's not working are one, two, and
three. and that. So, we'll look at those
real quick. All right. So, they were all
actually adjusted fine. They just
weren't clean enough.
So, the the little white star pushes
down on the switch and makes it touch
the other switch. Very simple. About as
simple as the switch can get.
See how it's moving the So, all you want
is the big blade to move the little
blade a little bit. That's good enough.
Um, okay. So, all the switches are
working. All the solenoids are working.
I guess we can actually play it. Yeah,
we can actually play it. Holy moly.
Okay, folks.
So, I'm going to show you an undeniable
truth
about pinball. So, here we go. Let's see
if she'll fire up.
So, reset our drop targets and kick the
ball out.
flippers are working.
The the left kicker it seemed like
kicked a little bit.
I don't know why that would have been,
but
flippers are nice and strong. That left
kicker kicked on its own there for a
second, though.
Some Sometimes the pop bumpers actually
do that.
I had that happen on a previous game.
We were just talking about that on a on
a previous video. All right. So, the
undeniable truth of pinball is they
freaking suck with no sound and it is
not fun.
The sound really adds a lot. So it
should be going.
Watch the left kicker. It might pop on
its own when the pop bumpers hit.
I have seen that happen before.
We've just won a bunch of points, you
know. Oh, I'm probably racking them up,
but I don't have any way of knowing
because the sound doesn't work.
All
right, let's see if we can get the the
the kicker to trip.
No, that's just been a fluke. There is a
thing on the classic valleys, some of
them, sometimes when the ball's hitting
on the early ones like this one,
sometimes when the ball's hitting the
pop bumpers, the left kicker will kick.
It has something to I can't remember. We
figured that out on a video one time
and I found a bunch of people online
mentioning it.
Oh, you see the little lane gate shut on
its own. Very cool.
Giving him points.
Of course, we can't tell that we're
getting points because the sound's not
working.
So, I also need to add a battery to the
display to the uh MPU.
And I've got a
something weird going on with the first
display. It's not right.
Um
not sure why that is, but I think it was
right before. Hm. Maybe we'll figure
that out. So, we still got a little bit
of work to do, but the next video will
be all about the soundboard.
So, we will do that next time. Hope
you've enjoyed it so far. Check out the
display. One of them's tripping. So,
we're just test playing it, right?
Obviously, we need sound. We've got uh a
digit screwing up on the display.
Everything else seems to be fine. The
left uh kicker kicked one time. I
thought that was going to be an issue,
but it stopped. Um there's still a
little bit of cosmetic stuff to mess
with.
And uh we got a pretty decent looking
little machine here I think. So I hope
you've enjoyed it. We will see you on
the next video where we will work on the
sound board. Now if you love these early
valleys,
you know who I've been thinking about a
lot lately for some reason. And the
reason is because of Jonathan. Jonathan
keeps sending me weird uh reels and
memes on Facebook. And he sent me uh a
evil conval uh uh reel. So, I've been
thinking about old evil lately. I'll put
the video up here of the time that we
got to work on the wonderful evil conval
pinball machine. One of my favorite bat
glasses. You know, evil, he jumped a
dirt bike. I a bike. It wasn't a dirt
bike. It was a Harley. So, when he
jumped, the back of the Harley was so
heavy that it like dragged behind him.
So, when most guys do those stunts and
jumps, their bike does this, right? It
then whenever they land, they land like
this. Not evil. When evil jumped, it was
so damn heavy. The back of it did this.
And so he did this through the air.
Right? It's just beautiful.
A moment in time. We will never see
somebody that damn dumb anymore. Right?
But uh the evil can evil pinball machine
was one of the best ever. So if I've
hyped you up enough, check out this
video.