it doesn't matter if you have power
tools to make the job go by faster or
you want to work with nothing but hand
tools and not even any electricity
anybody can make this workbench
remember glass half full not glass half
empty now this was made with readily
available materials I used nothing but 2
by 10 southern yellow pine boards to
make this entire workbench and it set me
back about 110 dollars for the wood the
bench itself is about 6 feet long it's
about 2 feet wide and it's got an over 4
inch thick solid wood top that's made to
take some abuse for those who are
interested I do have a set of plans
available to walk you through step by
step how to make this workbench it has
three different vise options and a 4
drawer cabinet that will go down below
as you can see I don't have the vices
mounted or the cabinet built that's
because there's only so much crap you
can cram into a 20-minute video I'll get
to those in the next video so let's get
down to business and I'll show you
exactly the steps I took to make this
really solid workbench just like most of
you out there I can't really justify
spending about a thousand dollars on
some really nice hard maple for a
workbench so instead I'm using a very
good budget alternative which is
southern yellow pine the workbench build
starts by making the top assembly and
that's because some of the base
dimensions will be derived from the
completed top assembly and I'm going
through all of my 6 foot long boards to
pick out ones that have really clean
edges along their full length and that
is because each one of these boards
needs to be ripped in half and then
stood up on end to complete the top
assembly I'll need about 5 really clean
boards or boards that are clean on the
end and that way once the bench is all
glued together and completed I'll have
enough material on top to plane away and
get a nice flat surface without having
any knots showing through on the top
side so once these boards are ripped
right down the middle then I'll go ahead
and start the milling process for at
least three phases to get this somewhat
more manageable before I put it in
clamps
i bypassed the jointer and just skip
planed all of the pieces that will make
up the workbench top and now I'm gluing
them together in three individual beams
once these beams are completed then at
that point I can run them through my
jointer and planer and table saw to get
them square four sides and then glue
those three beams together to make a
pretty flat work bench top before
assembly so that way once it's all done
there won't be much flattening needed
now as I'm gluing these together I'm
making sure that each beam has all of
the pieces bowed out at the middle and
that will that will create a natural
spring when you glue these together that
way I can focus more of the clamping
force directly in the middle and the
outsides will be naturally sprung tight
to begin with and I'm also using two
dedicated coals for each side of these
individual glue ups and that's because
the clamps that I'm using are going to
Mar the surface up and that way they
will damage the coals and not my actual
workbench top material after gluing up
all the sections that will make up the
top I started squaring them at my
jointer starting with the large face
that will eventually be the top of the
workbench and this will reduce the
amount of hand planing once it's all
completed after that I squared up both
short sides connecting to that top
surface now typically we wouldn't do
both of these faces however these are
pretty darn parallel and flat to begin
with so I don't think I'm taking them
out of parallel much and if I am it's a
very insignificant amount that really
doesn't matter I this is a much better
approach than running the full beams
through the table saw flipping them over
it's just not really manageable that way
after this I can run them through my
thickness planer and I'm only using the
thickness planer to flatten the bottom
surface of this top assembly for each
one of these sections and that's because
there's pretty much no way to get around
having some type of snipe on the the
beams this size as they run through the
planer so if I am going to have any
snipe I want them to be on the bottom
surface
of the workbench where there will be a
lot less noticeable and they really
won't even matter
I've milled the top section squared four
sides everything's nice and flat so the
glue up should be relatively uneventful
however I don't want any of these to
slip a little bit and cause a lot more
planning to be done on the top surface
so if you do have a biscuit joiner now
is the time to use one I do not have a
biscuit joiner so I'm going to use
floating Tenon's in the same way that
biscuits would be used once all the
floating Tenon's are in place and slap
some glue in the joint and clamp
everything together it should go
together nice and smooth without any
hiccups and I'm looking for a nice even
bead of glue squeeze-out
in each one of these joints the top is
completed and I flipped it upside down
all I need to do is finesse the top
surface once it is complete that's all
that's left to do with this particular
part of the workbench this turned out
very heavy which is good it's exactly
what you want in a workbench top however
my original intentions were to move this
to a set of sawhorses and build it
upside down from there but I think it's
going to be easier for me to manage if I
leave it here on my assembly table I
finished my humble table with
polyurethane so while it is really heavy
it is a lot more manageable on here than
what I think it will be on some saw
horses so next up is to build the legs I
needed to go through the milling process
for the legs and then cut some Tenon's
that will eventually fit into some
mortises on the bottom side of this top
you
with the legs out of the clamps I'm
using my jointer and planer to square
the legs for sides and then finally cut
the legs to their final length at the
miter saw the legs will attach to the
top with a through tenon and to cut this
tenon on the end of each legs I'm going
to make my final passes with the table
saw but I want to hog out the vast
majority of the material with the
bandsaw first I can't make all of my
cuts my finished cuts of the bandsaw
because my blade is really dull and just
not cutting that great
I've got the workbench top upside down
so the bottom side is facing up and I've
already determined where the start point
for my legs are going to be the the base
assembly is not going to be centered
it's going to be offset to one side so
I'm starting with the short side and
I'll work my way from one side to the
other marking out the locations for the
legs making sure to establish the
appropriate distance in between the legs
for the base cabinet that I will
eventually put down below I've already
established the start point of the leg
and which side of that line I want the
leg to be on so I'm just going to use
the tenon itself
pushed up against the top to mark the
other side so that is the start and stop
locations for the mortise now the
mortise will eventually be or the leg I
should say will eventually be like so
and the inside distance here how far the
mortise will start from the edge of the
workbench is equal to the distance of
this shoulder right here so we're going
to rotate this down and use the shoulder
itself to let me know exactly where I
want the mortise to start and then the
final dimension the opposite side is
equal to the total width of the leg so I
can slide the leg in place lining the
backside up against the other side of
the workbench and just strike a line so
this in here needs to be hog tout I'm
going to mark this on all four the
Tenon's on both sides of the workbench
really quick I hugged away the vast
majority of all of the interior space
for each one of the mortises with my
plunge router you can use a drill bit
and drill you could use a chisel and to
get all this stuff out of the way but
this has dust collection systems
throughout I chose now I did not go to
the line at all on any one of these
mortises and that is because I wanted to
attach my my edge guide here and that
will allow me to establish this nice
clean perfect outside face for each one
of the mortises with one set up so I'll
go ahead and cut all of these
appropriately and make sure that there
are they are all perfect
before adjusting the base once more for
the inside face of all of the mortises
and then I'll just repeat the process
for that and trim up the end grain sides
of the mortise with just a regular
chisel and a mallet
I finessed all of the legs so they're
fitting in the mortise is just fine one
of them is a little bit less than
perfect but that's okay they're all
going to be wedged from the top side
once it's all assembled before assembly
though I don't I do want to make sure
that I drilled a hole for the leg vise
and I'm going to do that right now just
so I don't forget about it
up next I'm going to cut and make the
joinery for the long short and short
stretchers then I can glue this thing up
and start start installing some vices
I just milled up the beams that will
make the long and short rails for the
workbench base now I'm using half lap
joints to connect everything so I'm
going to cut them on the beams first the
long and short stretchers whatever you
want to call them and then I will mill
out the appropriate joint locations on
the legs now I've already made sure to
mark the appropriate spots for these
joints because for me getting this far
in the game it's very easy to get mixed
up and cut the wrong joint in the wrong
spot so hopefully that will prevent me
from doing so
to cut the matching half-laps on the
legs and starting with the short rails
and the first thing is to line up the
fence so that my dado blade the outside
of my dado blade is lined up with my
start line with the blade on the cut
side of that start line once I have this
position the way I want it I can make
the first cut on all four of the legs
that will that will make sure that the
the half flaps are in the exact same
spot on each one of the legs then I can
hog out the majority of the material on
the rest of the legs making sure to stop
about a quarter of an inch shy of where
my final cut needs to be I can move the
fence and dial this last cut end
absolutely perfectly and once the fence
is in in the appropriate spot then I can
make my final cut on each one of these
legs to make a perfect half lap on all
of these at the exact same time then I
can repeat the entire process again for
the half laps for the long rails
all the hard work is done all the joints
are cut and they fit and I have it all
clamped together in a dry assembly these
joints will eventually be pinned with
oak dowels in a couple days or so but
for right now I'm going to pin them with
screws and the screws are going to be
used as clamps so that way this thing
can hold together as it dries as you can
see I don't really have a good setup to
clamp this thing long ways so I want to
get the screws driven first before I add
any glue that way I can remove the
clamps and then just use the screws by
themselves they'll go back into the
holes that were previously made and the
screws will be the clamps to hold it
together as the glue dries once the glue
dries then like I said I can come back
in a couple days and put the oak dowels
in their place I was able to lift the
workbench top off of the legs by lifting
up on side and hitting the leg Tenon's
down just maybe a half of an inch or so
and then putting a clamp underneath it
to prevent it from going back down going
to the other side and repeating the
process till eventually I had the work
bench top sitting on top of the leg
Tenon's just freely sitting there so
gluing it up is going to be a multiple
stage process I'm just going to glue the
legs into the work bench top first and
I'll do so by putting a bunch of glue
way more glue than what's necessary
inside the mortises for the legs and
then I'll gently slide the top onto the
leg Tenon's and then from there once all
of the leg Tenon's are just started I'll
go back and forth from side to side
lifting up the work bench and slamming
it down using the weight of the work
bench to properly seat off all four of
the leg Tenon's making sure that these
shoulders are nice and tight and that
the Tenon's are all the way through once
that's done I'm going to use some small
wedges that I cut at the bandsaw just
just scrap pine wedges the same materi
I'm using for this workbench and wedging
the sides the short sides of the tenon
making sure it's nice and tight and
everything is nice and glued in place
and now that the workbench top is
properly joined to the legs I can remove
the screws from one structure at a time
insert glue into the joint put that
particular structure back in place and
use the screws to clamp it all down once
all of the joints have had a proper
amount of time for the glue to dry I can
come back with a flush trim saw and cut
all of the joints nice and smooth on the
top surface only is where I'll use a
hand plane to make the Tenon's flush
with the top surface I'm not too
incredibly concerned with the base at
this point so the construction of the
actual workbench is now complete and I'm
very happy with it is it perfect no it's
not perfect there's some flaws here and
there but I really don't care because it
is solid and that's all that matters I
didn't build this benched if you have
something pretty in the shop that you
can't really work on because you don't
want to mess it up this is going to take
abuse and I'm going to abuse it and it's
just a big heavy work wedge I don't know
the exact weight but this thing is heavy
enough where it's not going to move when
you're working with hand tools on it at
all but it is light enough to where I
can still manually push it around the
shop if needed all of the legs are the
same length but it's not level on my
garage floor because my garage floor
isn't level no matter where you push it
it's going to rock just a little bit so
the quickest solution for that is it
just kick a shim underneath the high leg
and that's good enough
the final dimensions are one half of an
inch shy of six feet it's 23 and a half
inches front to back and the top stands
at 34 inches off the ground the top
itself is 4 and 3/16 of an inch thick
and the legs are 4 and 8 by 4 and a
quarter
I do have plans available for this like
I said and the plans go into detail for
the workbench itself plus three vise
options as well as a full cabinet to go
down below with four drawers so that's
it for this video I will cover the vices
and the cabinet's later thanks for
watching hope you guys enjoyed this I
had a lot of fun here in the shop making
this and I'm looking forward to putting
it to use so you guys take care have a
great day and I'll talk to you next time
you
you