Using more scraps from previous Trash to Treasure projects. After seeing the last set of salt and pepper shakers my mother asked if I could maker her a set. Cant say no to mom ;)
Like and Subscribe if you like what you see! Twitter @jaybates86 facebook.com/jayscustomcreations youtube.com/jayscustomcreations
Check out my other channels SolidWorks, AutoCAD, and SketchUp designs: www.youtube.com/JaysCADD Household and apartment maintenance: www.youtube.com/ApartmentMaintenance Project plans: https://jayscustomcreations.com/plans/
So I still got some scraps left over and what I think I'm going to do is make a walnut and
maple salt and pepper shaker.
And I found four pieces of maple that are the same size.
So I'm going to take some of this walnut stock and cut it down to the same length as those
maple pieces.
And I'm going to use the same style as last time except I'm going to use the body as walnut
with a maple stripe and that's going to be your pepper.
And then the body as maple with a walnut stripe and that's going to be your salt.
So I've got my stock block set up and I'm just going to mill this down real quick.
Alright I've got all my stock milled down.
I have no clue how long these are.
I really don't care because I'm going to fly through this and make this quick and easy.
My body pieces and my veneer pieces.
So the walnut sides are going to have a maple veneer for the pepper.
It will look like so.
And then the maple sides, the maple body, will have a walnut veneer like so.
I'm going to get all this clamped up.
It's going to have to sit for a little while so I'll get this clamped up and I can do something
else in the meantime.
Alright so I got my blocks out of the clamps for the initial glue up.
Just like last time, you know, glued up a veneer strip in the middle.
This time it's a little bit thicker.
I've got a half inch strip in the middle and I think the overall body is two and a quarter
so it's about three eighths of an inch wider than the last batch but I still have to trim
it down.
Trim it down and glue it up like so.
First thing I'm going to do, actually the only thing I'm going to do right now, is putting
the veneered side up against the fence.
I'm just going to run this through and take off just a little bit just so I can get these
two faces on the same plane.
That way I can glue my blocks together and I can size and dimension as needed after that.
So I took it down a little bit further than what I just said I was going to.
First on the sides that were sticking out like so, I just ran it through to flush those
faces up smooth and coplanar so they're on the same plane.
That was my only objective but then it dawned on me that I still need to remove thickness
so that when I put my other half inch, when I put my other half inch veneer in here, I
guess you'd say half inch veneer, I don't know, spacer, that way I get this thickness
that same distance, you know, both sides.
So what I did is that, like I said, I got these on the same plane, flipped it around
and just skimmed by to clean up the finished edge, flipped it back around and then trimmed
it up to my final width so that I can take my piece and add my half inch and now I'm
at the correct width so that's cool.
But in the meantime, in the process I should say, I made some of these, I didn't make them,
these cutoffs, these little small thin strips.
This is just what fell off when I was trimming these up and future ideas down the road, can't
do it right now because it's too far into this project to switch around but something
that I think looks really neat is instead of maple, walnut, maple, let me see if I can't
get this, instead of maple, walnut, maple, you could do that.
Maple, walnut, maple, walnut, maple.
So just with these thin strips, a couple different looks, I'm already committed to this so I'm
going to keep going with this but I really would have much rather had that so.
And to see how it looks on the walnut, let's see, and to see how it looks on the walnut,
like so.
You know, like I said, I think that looks a lot better but I'm already committed to
this so good ideas, maybe next time.
Alright, so now I've got my half inch strips and time to finish gluing this up.
And I have found that if you just take your small pieces and just simply press them into
place for a good 5 or 6 seconds, then it already starts to hold.
Now I don't know if that's just suction because I squeezed so much glue out or if it's actually
the holding power of the glue, I don't know but anyway, it will help you out a little
bit because holding these small pieces where they need to be under clamps can get a little
tricky.
For the tops and bottoms of the salt and pepper shaker, I'm just going to match the bodies.
I've got a thin piece, it's about a quarter inch thin piece of walnut that I'm going to
be able to cut a couple pieces out of and I'll just use the walnut as the top and bottom
of the walnut body pepper shaker.
So that's done for the pepper shaker.
For the salt, I don't have any thin strips that look like that or rough dimensions so
I'm going to cut this out of some of that headboard material.
Alright, I just took them out of the clamps and salt and pepper.
I'm just going to run them through the table saw to clean them up and dimension them up
a little bit smaller, mainly because my piece of walnut that I'm going to use for the top
is the same as the last poplar piece that we did.
It's not as wide as I need it to be so no problem with the maple, it's actually a lot
bigger than needed.
Anyway, I'm going to trim these down to about two inches and get them nice and square.
After that, I'm going to glue the top and bottom on.
Actually, excuse me, before I glue the top and bottom on, I'm going to cut these flat
and drill the holes.
So let's get to it.