Hey guys, today I'm going to be remaking this clamp rack,
but before I do so, let me tell you the reasons why.
When I made this clamp rack,
I wanted to make a universal design
that would hold just about anything.
So I've got some F-style clamps on here,
some quick grip clamps will work just fine.
You can hold these pad style face clamps if you want.
You could hold just about anything,
bar clamps, pipe clamps, whatever you want.
Even stuff that doesn't belong, like a hammer,
you can still hang it here.
And this is what I do is I put all kinds of crap on here.
And for that, it's very handy.
When there's an individual layer of one particular row,
it's very handy and it works really, really well.
So for the concept of it, I'll give it a thumbs up.
For my execution of that concept,
I'll give it a thumbs down.
The problem is when you have multiple layers
that have to interact with one another,
I'm obviously not a CNC machine
and I can't produce that type of accuracy just freehand,
which is what I did for all of these cuts.
So having every one of these line up with one another
is very difficult and nearly impossible to do.
So anytime you have something that interacts
with multiple layers, like any of my long clamps,
you run into some issues.
Some being that a few of these areas are really loose
and a few of them are really tight.
So this one's extremely loose,
meaning that this is easy to fall out
if the clamp rack is bumped or something like that.
Well, some of them are really tight.
So what happens is if I go to pull
one of these tight ones out and I'm not extremely careful,
then some of these smaller ones end up falling,
which is a deal breaker for me.
Some of this stuff is falling down
and it's okay if you see it coming,
but anything that catches you off guard
is kind of dangerous and more annoying than anything else.
So instead of going with this universal design,
I think I'm gonna go with a much smaller unit
that stores the clamps from the wall out.
There's two main design criteria for the new clamp rack.
Number one, like I said, store the items from the wall out.
And the second one, I wanna borrow a concept
from my hand tool wall.
I've had this for about four months now
and something that I really like about it
is it's all based upon a sheet of plywood.
So if I need to make any changes,
such as remount the saws in a different location, whatever,
I can either unscrew the brackets
or simply just drill a hole into the plywood
and insert a dowel.
It's super easy to do and allows for basically
an infinite amount of changes.
So for that particular clamp rack,
I want to have a solid piece of plywood for the backing
and a little bit of extra space to allow
for any type of changes that may come down the road.
Like with most other shop projects,
I'm also not trying to spend any more money.
So I wanna use the plywood that I have here in the shop
to make this.
And something that really helps me
if I'm not using SketchUp to lay out the project first
is to actually use a large work surface
to kind of get an idea for the size
and what we can work around.
So the sheet of plywood that I'm gonna use for the back
is 40 inches wide.
And this allows me to use my work table
to establish a zone to work in.
And this level represents the far width
of this piece of plywood.
I can lay out my pieces the way that I want them
and get an instant visual representation
of how this is gonna work.
And from this particular situation,
I think I can get all of my main clamps
into about two thirds of it.
And that'll leave me all kinds of room over here
for small hangers, for small stuff,
or individual items and miscellaneous stuff
that may change down the road.
So this is going to be approximately 35 inches tall
and 40 inches wide,
and should stick out no more than 10 or 12 inches
from the wall, I think.
The plywood that I'm using is already 40 inches wide,
but I need it to be 35 inches long.
So go ahead and make that cut on the table saw first.
Went ahead and laid out for my brackets
just to make sure that I had enough material.
And I'm gonna go 12 inches away from my back piece.
It might stick out from the wall a little bit much,
but I can always trim them down.
So 12 inches away from the wall,
or the back piece, I should say.
And then I'm gonna go up 10 inches for each one.
Now from these two points,
I'm gonna come down three inches and in three inches
and strike a diagonal.
And that's gonna be the shape of the bracket.
And because there is a matching diagonal here,
I don't necessarily have to go 10 inches,
cut it off, 10 inches, cut it off,
because I'll have a lot of waste.
This triangle will be rather large.
So instead, I can flip the next piece over
and nest these two amongst their common diagonal here.
And that way I can get two pieces
in about 15 and a half inches of plywood
rather than 20 inches of plywood.
And if I did the math properly,
then this means I will get one, two, three, four, five,
six sets of brackets out of the off cut from the back piece.
And those six sets is exactly what I need
for the topmost row of hangers.
I taped together all of my bracket pieces
because I think it's gonna be easier
to cut them all out at the same time.
And to do so, I'm using the bandsaw.
I would normally use my miter saw for this,
but the sliding feature of the miter saw
doesn't have that much reach.
So the bandsaw is the next best option.
And the resulting pieces all have a point on one end
that needs to be removed.
So I'll go back to the miter saw station
to get a cleaner cut and remove all those points.
And the last step before attaching these to the back
is to establish a two degree bevel
on the tops of all of these brackets.
So that way everything leans a little bit towards the wall
rather than accidentally wandering out
or wandering forward as I interact with the clamp rack.
I clamped a couple blocks to the back panel
at the height in which the bottom
of the top brackets will be.
And what this will allow me to do
is rotate the board around
and set it up vertically,
just the way it will be up against the wall
onto my assembly table.
And then I can clamp the back panel to the assembly table.
What this does is it gives me a reference surface
of the assembly table to use
and more easily line up all of the top brackets.
They'll just sit in place while I secure them
exactly where they need to be.
I'm a fan of symmetrical items,
items that have symmetry about them.
So instead of starting from one side
and just stopping two thirds of the way through
with all of my larger brackets,
I put half of them on one side,
half of them on the other side,
and then I'll just load them up
with the long clamps on the outside
and getting shorter as I go towards the middle.
Just personal preference, it really doesn't matter.
But I wanted to go ahead
and put a couple of these in place,
a couple of the clamps in place,
so I know where they are going to reside
as far as their length goes.
And that will determine
where these smaller F-style clamps will be mounted.
Now these brackets are gonna be spaced out
a little bit differently than these,
so I did wanna get these in place
so that I can put some reference marks on the back panel.
And also these are gonna be used a lot more frequently,
so I want them much lower in the rack
and much more easily accessible.
For the F-style clamp brackets,
they do not need to come away from the wall
a full 12 inches like the other brackets do
because these clamps are not as wide in that direction
as the other clamps are.
They're a little bit more thinner profile.
So I've already got a piece of plywood
that is eight inches wide,
and that's a perfect distance
to come away from the wall for these brackets.
I just need to cut eight of them
down to six inches in length
for the height of the brackets.
Now on these, I did not make an angled cut
on the outside bottom corner,
but I did do the same two-degree bevel on the top
so that these clamps will have a tendency
to go in towards the wall rather than come out.
So just like every other super easy shop project,
I should have done this a lot sooner.
This is a big improvement over the last one.
It actually takes up less space.
Now I wasn't dying for more shop space,
but it does take up a lot less space.
And it's easier to get what I need
and not worry about stuff falling.
So all of my F-style clamps are right at chest level,
which is a little bit easier than grabbing them way up high,
which is where they were previously with my quick clamps.
But all of the longer clamps are easy to remove
and really easy to throw back in place
and not worry about specific placement
and not worry about the next one falling off.
These pipe clamps in the last layout
were really easy at falling off at you.
And this is very convenient and foolproof.
I didn't put everything back on here
because I did have a lot of crap that I didn't really use.
And I didn't make specific holders for these spring clamps
because I just clipped them to a piece of quarter inch Luan
and had a T built up on the top previously.
So it can sit into the bay of my 50 inch pipe clamps
that I very rarely use.
And typically when I'm using a spring clamp,
I'm using a bunch.
So I just grabbed this and go with the last layout
and I can do that with this one as well.
Also have a lot of extra room right here.
Don't know what I'll put there,
but I'm sure things will change
and it's empty real estate ready to go.
The benefit with the vast majority of shop projects
is that they make your shop more inviting
and more encouraging and just more welcoming
to be in the space actually making stuff.
So anytime that you can increase the likelihood
of you actually being in your space
and enjoying your workspace,
definitely take those opportunities to improve upon it.
This is one of many shop projects that I've made.
I've got a full playlist of all my shop projects
if you wanna check that out.
If this is your first time here
and you wanna see more videos just like this,
then be sure to subscribe.
That way you don't miss the next one.
I post about once a week.
And if you're interested in more kind of
behind the scenes stuff,
check out my second channel.
For the past 93 or four weeks,
I've been doing a weekly Tuesday update,
kind of what happened last week,
what's gonna happen this week,
and just some behind the scenes stuff.
So check out my second channel if you're interested in that.
You guys take care, have a great day,
and I'll see you next time.