A Jewelry Box For My Daughter - Cracked Bandsaw Box

Jay Bates
100 followers
Jul 15, 2025
2013 version: https://youtu.be/S8xZETRC0So
The template for this build can be found on my website: https://jayscustomcreations.com/2023/12/a-jewelry-box-for-my-daughter-cracked-bandsaw-box-2023/
→ Yost clamps: https://amzn.to/3GMKimB
----------
----------
Mailing Address:
PO Box 33
Mathiston, MS 39752
Social links:
Lbry - https://lbry.tv/@jaybates86:3
Odysee - https://odysee.com/@jaybates86:3
Twitter https://twitter.com/JayBates86
Facebook http://www.facebook.com/jayscustomcreations
Instagram= http://www.instagram.com/jaybates86
J's customer Creations is sponsored by
bits and bits use the code J Bates to
save 10% off your next router bit or CNC
bit purchase at bits bits.com a decade
ago in 2013 I bought this band saw and
shortly after buying it I made a bunch
of these cracked Band Saw boxes well
about a month ago I restored this exact
band saw a decade later and now another
decade later I want to make another one
of these cracked Band Saw boxes this
project starts by getting a piece of 84
popler that I have in my lumber rack and
I'm going to cross cut to remove all of
the defects but also I want to keep this
as long as possible while I go through
the jointing and planing stage so first
up I'm going to use the jointer to Joint
one wide face nice and flat then I can
go over to the planer and plane an
opposite face flat and parallel and
sometimes when you do this obviously
it's a planer so you're going to get
some planer snipe but here is a trick
for you so this one I did not use my
typical uh infeed and outfeed snipe
board I just ran them through to show
you that this is snipe and this is kind
of annoying it just comes with the
territory of using a planer however if
the interior of the board or the the
center area of that flat face is nice
and flat and parallel to the reference
face that we just established at the
jointer it if that's the case then we
can go right back to the jointer and get
rid of that snipe making sure that we
only reference off of that Center area
of the wood of the of the wood and not
the ends where that snipe actually is
one absolutely satisfying byproduct of a
properly tuned and calibrated jointer is
when you try and lift the material off
of the outfeed table and it's kind of
like suction CED to the table that's
when you know it's really really flat
one final trip back to the miter saw to
Crosscut the three pieces that I need
for the glue
up the idiot donkey strikes again
yesterday I forgot to turn my microphone
on but
today today I can read so today should
be
better regarding this template I have
absolutely no idea where it originally
came from this is not my design somebody
else came up with this years ago uh but
all I did was print off this particular
image scaled it up just a little bit so
that it took two pieces of paper regular
uh letter size paper and then stuck them
together the overall height while I was
shooting for was about 13 in I have a
14-in band saw so that kind of just made
sense and when it comes to aligning
these templates that take multiple
pieces of paper the easiest thing to do
is tape your first piece up to a window
and then you can very easily align the
second piece on top of that making sure
all of the uh the the geometry on both
pieces of paper line up appropriately
here's a feature that I wish more clamp
manufacturers would Implement and that
is these articulating handles yes you of
course you do not need articulating
handles to crank down on it so
aggressively that the the bars Bend and
it just super super overtightened no
that's not the point here the point is
to take a little bit of pressure off of
your wrists if after a long day your
wrists are a little bit sore and not
what they should be I guess you could
say this is kind of a a comfort
convenience I didn't really feel like
going back into the house to rummage
through my daughter's craft supplies to
find her glue stick so I just used
regular wood glue to glue the paper
template to the actual piece of wood
which you know paper is wood so wood to
wood yeah it works now the absolute fun
can begin I'm using a 1/8 of an inch
wide blade on this band saw it has a
maximum throat capacity of about 6 in
which is why I used uh three layers of 8
quter material and like I said uh it's
about it's a 14-in band saw so about
13in height on this particular design
works out quite well there's a lot of
waste here I kind of glued together way
more material than what I needed however
this particular board that I was working
with was kind of one of those Oddball
boards that like what else were you
going to do with it kind of a thing so
I'm okay with the waist here it'll heat
me up quite well in my fire pit uh it
aand saw it it aand saw is one of those
things that is kind of sort of like you
know once you learn to ride a bike you
you know how to ride a bike forever but
it's also kind of a skill going around
corners that if you don't use it you
lose it right there's a lot of things in
life if you don't use it as you grow up
you lose that kind of agility or
athleticism well same with being precise
with corners and curves on a band saw I
used to be really really comfortable and
precise on a curve cutting Band Saw cuz
I used it all the time well I haven't
had this particular saw in my shop for
many years and cutting curves on the
band saw is something that I haven't
done for many years so a lot of these
these cuts and Corners as I'm going
around this just weren't um uh the cut
quality wasn't as good as I had
remembered we'll say that the last part
of establishing the perimeter is the
bottom little opening area in between
the feet and that's the last thing to be
cut out before cutting the front and
back off now in this case I do have a
second bands saw that is dedicated to
resawing however I had a little boo boo
or a little accident little hiccup with
it not too long ago and bent one one
tooth on this band saw blade forgot all
about it and just made my resaw cuts to
cut the front and the back off and let
me tell you those cuts were not not
Smooth Cuts By Any Means so I had to
actually sand a bunch of this uh later
on down the road before I glue these
back on so that was that was kind of
annoying no you don't need two band saws
to make a band saw box I had one set up
so I used it with the front and back
removed the center feet area on the left
and right of the Interior can be removed
and once that's removed we stack it back
together so you have the back the middle
in the front and you're left with well
what looks like a really goofy
fun comical type of a dresser chest of
drawers it's it's a really really fun
design I really like whoever designed
this I I really really like this design
after what felt like a ridiculous amount
of sanding which turned out to be not
enough sanding I glued the front back on
to the middle assembly the middle
section and that's necessary so we can
actually start cutting out the drawers
to make this an actual box so the first
four drawers on the top are pretty easy
and pretty straightforward you start in
the crack area and then you end in the
crack area very easy simple Cuts now as
you go down the dresser the chest of
drawers you have to to slice the the
interior dividers or the horizontal
dividers you have to slice them apart
from one particular side as you continue
to spiral your way through uh through
the piece and that's okay that's just
you know what has to happen on a Vans
saw box we're going to glue that
together in the next step
anyway
here you can see what happens to the
entire structure as the drawers are cut
out we have to glue this back together
and the the design of the template that
I'm using here has the lines extending
through the cuts that we just made so
it's very easy to line everything back
up a little bit of glue 16,000 clamps
you know the routine just like with the
main carcass or the main assembly of
this box all of the drawer fronts and
backs need to be removed I learned my
lesson with that Bent Blade on my
resawing bands saw so I resaw everything
here at what I'm calling my curve
cutting bands saw no problems whatsoever
and speaking of no problems I really
want to make sure that I removed the
material making a drawer and not a a lid
I guess you could say for each one of
these drawers so I'm putting them back
into the carcass making sure that
everything's in the correct orientation
then I'm striking a line on the top of
the air area that needs to be removed
now once the line is there and I know
for sure what is the top I can focus on
removing the inside so for demonstration
here's the material that I kind of need
to remove on this particular drawer then
one by one we go back to the band saw to
cut out a bunch of more material once
again this is all just dishing out the
center section you don't really need to
draw some guidelines unless you just
really want to kind of eyeballing it at
this stage is is PL plenty good enough
remember the drawer fronts and drawer
backs that we cut off a little while ago
well we've got to glue them right back
into place this is that's the story of a
band saw box slice a little bit off
slice out the interior glue it back on
with the drawers and clamps and the
carcass out of clamps from the last glue
up I'm using fast setting Glue by the
way uh the back panel can be glued on
and here's where you're going to run
into some alignment issues remember when
we cut out all of the drawers we had to
cut right through those horizontal
dividers as worked our away down the
band saw box and when we when we cut
through those dividers we removed uh a
little bit of material from the width of
this box equal to the curf of the bandol
blade well that removal of material is
eliminated when we glued it back
together and that means the center
section is actually more narrow than the
back panel is that we cut off previously
so here's where things won't really
align all the way but don't freak out
perfectly normal it is a new day all the
clamps are put away the drawers are
installed in the carcass and at this
point all of the drawers are now inset
drawers because we removed the front and
back of each one of the drawers and
glued them back into place therefore we
have two curf thicknesses or curf widths
from the band saw that we actually were
we actually removed from the front and
back dimension of each one of the
drawers you can leave it like that if
you want if you want inset drawers
you're basically set up ready to go I
don't want inset drawers I want the
drawers to be flood with the front face
of the chest of drawers so instead I
shoved some paper towels into the
cracked area up at the top just to stop
those two or four drawers from rattling
around while I went over to a belt
sander and sanded the front face frame
or the front face of the chest of
drawers flush with the uh drawers inside
now easiest way to check your progress
is is the paper is the paper gone if
it's not keep sanding sand it until all
the paper is gone and then you know
everything is nice and flush and sanded
while I'm over here at the belt sander
might as well take the time to sand the
top Arch nice and smooth as well as the
entire side of the chest of drawers on
the little drum or the outside wheel of
the belt sander remember when I said if
you don't use it you lose it and I
wasn't really wasn't really hyped about
the quality of my curves around this too
much starting and stopping well here's
what it looks like when it's before it's
kind of Blended and you can really see
just how inconsistent I was going around
the corners that's okay we're going to
sand all that nice and smooth uh
starting by putting a fan blowing away
from me with a filter on my workbench
that way I can keep sanding and blow the
dust in the air it's going to get sucked
up in that filter and away from me and
not uh not breathing all that stuff so
doing a lot of hand sanding to all of
the drawers uh put a I I put some
sandpaper on a wooden block to sand the
flat faces which basically basically was
just the inside of the little cracked
cuts and then there's some more sanding
a little bit more sanding after I was
done sanding and then I sanded a little
bit more and then some areas actually
required a little bit of rasp work
because I didn't line things up properly
and then I I sanded a little bit more
after that and then uh I did a little
bit of sanding a little bit more sanding
and then the next step was back to the
rasp to uh round over the inside faces
of inside of the openings on on the
carcass itself and then after I did that
there's a little bit more sanding and
then uh flipping you know flip it around
again to do a little bit more sanding
and then uh right when you think you're
done there's a little bit more sanding
that you have to get done because
there's always more sanding to do after
all that wonderful feel-good Smiley
sanding is done uh you can kind of see
that all the jaggedness is pretty much
gone uh all of the perimeter of the
drawers kind of just falls into a
blended Shadow which is really really
nice and for a finish I really wanted to
oil this to I I kind of like the way
that like greenish Hue of popler looks I
know it's not one of the most desirable
Woods out there but I really like the
way pop looks in that regard but this is
my daughter and she's on the sky blue
kick and she actually picked out this
paint a little while ago so I'm going to
I'm going to paint it for her and like
any other sane person out there would
probably start painting from the inside
out but no once again the idiot donkey
strikes again and I paint from the
outside in making everything just a
little bit more cumbersome and
frustrating but that's okay I got it
done for all the drawers uh the drawers
that could fit inside the the can of
paint I just dipped the front of it in
and then just brushed off all of the
drips and all that and then for
everything else I just brushed just the
front of the rest of the drawers the
drawer poles are the only part of this
project that I was kind of up in the air
on I didn't have an answer before I
started the build so my my thought was
to just kind of lean on what I did in
the past and that is Mill up some uh
poppler that is qu in thick Quin wide
however long it needs to be for each one
of the drawers I did that put some kind
of in place visually
and it just I just wanted to go a
different route there just wasn't
anything special about it so I was
looking around the shop to find
something that I could use as drawer
poles and it dawned on me that each one
of these drawers is a different size
well festal dominoes come in many
different sizes many different size
thicknesses as well as lengths so why
not use them to kind of correspond to
the different sides of these drawers and
also along the length of each one of
these dominoes is a bunch of lines I
think they just compress them for glue
squeeze out reasons or something like
that uh when you actually use them as
they're intended to be used but visually
I think it's a little bit interesting
and it'll also provide a little bit of
kind of a tactile feel as you pull the
drawer open so so I set up a stop block
and used the handsaw to as accurately as
I could or more consistently as I could
cut all of these down to a specific
height uh for each one of the
drawers and then just mixed up some
two-part epoxy and glued them in place
this is one of those areas that I'm like
I was like I said I was kind of didn't
really have an answer before I started
and I think it turned out really really
good as far as using this particular
item for the door PES is it it just kind
of worked out really really really well
I think I purposefully only painted the
drawer fronts and not the drawer bodies
because these top four drawers I know
that the sides were going to be exposed
and if I painted them blue yes you you
can see this crack no without question
you can see the crack in the design of
this Banda box but if the sides of those
drawers are blue it would kind of blend
a little bit more this is something that
you want to feature you want to
exaggerate and the way I'm wanting to
exaggerate the crack is with contrast so
for that reason I only painted the
drawer fronts everything else that's
exposed gets a coat of natural Danish
oil making sure to not get it on the
blue at all not not get it on the paint
although I don't think it would hurt it
at all it might yellow the blue just a
little bit so uh I painted it all on the
drawer boxes or the the drawers
themselves I kind of lathered it on
there and then used a very fine paint
brush to just ever so carefully Get It
On The Dominoes or the drawer poles
because you're cutting off the front and
back and then gluing them back on odds
are you're not going to glue these back
on so that there's no rock in the U the
bottom feet so to stop the rock I put it
on a flat a known flat surface my table
saw and used a piece of sandpaper under
one of the high legs and just pull it
out a couple times uh that will take
care of any Little Rock that you have
all right what do you think of this
thing honestly this is such a fun
project it's a fun project to make
because it's just a lot of fun curves at
the band saw uh and it is it's it's one
of those projects that you can get away
with a lot right you're not trying to
stay Within These tight restrictions of
of rectangles and whatnot you you're
making curves so there's no such thing
as what what the curve needs to be you
can make it whatever you want to be make
it whatever you want it to be and this
this design is it's just fun right it's
just really fun there's a couple things
that I really really like that I'm glad
I did number one I'm really glad I only
painted the drawer front and not the
entire drawer that way the the crack
it's obvious that there's a crack right
here but it's it's exaggerated it's
highlighted by the the wood contrast you
see here on the side rather than it
being all blue I really like that The
Dominoes for the drawer poles that
worked out in my opinion there's it's
it's kind of hard to see on camera but
each one of these dominoes has I don't
know if you can see that there's ridges
all the way along here so it's it kind
of gives it like a little bit of a
tactile feel as you actually interact
with them I like the fact that they're
different thicknesses that as this kind
of shrinks in the middle so do the door
pulls and really all I did was was rip
these to a a common um rip them to a
common width and the rest of the
dimensions and sizes just just natural
to what they are Festival dominoes so
that that's pretty fun U my daughter is
going to love this I'm excited to give
this to her as a Christmas gift and uh
yeah it's just a lot of fun to make so I
encourage you to make a band saw box if
it's not one of these the exact designs
have fun make your own design Banda box
is one of those projects that you can
make it any shape you want really just
just have fun with it um yeah if you're
interested in this particular particular
uh image that I used for this one I have
it available on my website it's actually
been there since 2013 that particular
image again I don't know who originally
created it but whoever did thank you
because this is a really fun design uh
that's it for this video go to my
website jcustom creations.com newsletter
and sign up for my email newsletter so
you don't miss anything that I publish
you guys take care have a great day and
I'll talk to you in the next
video
[Music]
