Check Out Our Patreon Account, for Unreleased Repair FAILS, Concise Repair Tips Not Possible In This Long Form Video, And 1 on 1 Repair Assistance with YOUR Project!
Thank you to everyone who has been supporting our channel! If you use the link below before you purchase anything on Amazon, we get a royalty for sending you there, thank you!
Our store is located at 139 Caldwell St., Rock Hill, SC 29730.
Ladies and gentlemen, this is Joe's
Classic Video Games back with another
cool pinball repair video for you this
evening. We have been working on this
kind of beat up Valley Supersonic for
quite a while now. We've done several
videos on it. Uh we bought this used off
of Facebook and the boards were all
fried in it. Somebody had made a short
on one of the boards and it fried all of
the other boards. So, we did a bunch of
videos going through that, but it's also
kind of beat up. like the cabinet is
kind of beat up and the playfield is
very beat up. So, we did a video or a
couple videos actually where we've been
working on this thing trying to hand
paint the art back in to save it. So,
we've removed all of the the pieces that
go on it. We have them over here on our
beautiful funhouse that's being used as
a table right now. And uh previously we
kind of focused on putting some of the
lines back in the line work. You can see
where the wear was. Um, this S was
completely missing. Most of this one was
missing. And, uh, we've done the orange.
So, we've done some of the lines and
we've done the orange. We also did like
kind of the cream color.
And, uh, we're kind of going through it.
It's still a little bit of a mess, but
it's getting there. So, I think next up,
we probably need to go ahead and try to
repair the red.
Red is kind of a hard one to do because
it's kind of thin. Um, so we need to do
some primer first. So, we've got, if you
look at these, we mentioned it in the
previous video, there's only really a
few colors. So, it's not as hard as it
seems. Um, the hard part is kind of
getting the art back where it goes. And
since this doesn't actually even have
art, it's just kind of simple shapes, it
was a lot easier, right? So, it looked
really bad, but it's not that bad. Um,
so we've you've got a yellow. You see
the yellow,
some of this with the cream on it cuz I
just did that for primer, which we're
about to do on this. You got the yellow.
Uh you've got a blue. That's two. Um
you've got a cream, which is kind of it
was originally white or a whitish color.
That's three. Um you've got red, that's
four. You've got this burgundy looking
color. That's five. You got orange,
that's six, and you've got black, which
is just the lines. That's seven. So,
there's only seven colors on the whole
thing. They also have this wood tone.
That's just the natural plywood, but we
don't have to touch any of that up. So,
seven colors. We've already done the
cream and uh we've already done the uh
orange and to a great extent, we've done
the black. On the black, I'm able to use
just a a acrylic paint pen. These are
pretty cool.
These aren't really that expensive or
anything, but it's acrylic paint as
opposed to uh oilbased paint or u
something like a Sharpie or something.
If you use that, and it's real tempting
to just use a Sharpie or even an ink
pen. If you use that, the problem you
have is whenever you clear coat over it,
it the catalyst in the clear coat
interacts with the whatever the catalyst
is in the Sharpie and the paint will
run. Sometimes you get away with it, but
a lot of times you don't. We had a KISS
that we did one time. We touched up the
side with a Sharpie.
So, KISS has the four faces of the band
members on it. We touched up the side
with a Sharpie. Went all through it.
Took forever. Got it all just right. And
then we put the clear on it. and all of
the paint started running off their face
like they were crying like little
babies.
All right, so yeah, let's do red. I
think if we if we get the red done,
it'll make a big difference. So, we've
got all the red here that's missing.
We've got a little red here that's
missing.
This we could touch up a little bit.
And then up here, there's some areas
that are, you know, screwed up. So, it's
really there's really not a ton of red.
So, let me grab my paint and see if
we've got a red that's anywhere near the
color that uh the Playfield is just
right out of the bottle. And hopefully,
we won't have to mix anything. So,
here's what I've got. Now, we just get
these little cheap They used to be 69,
but I don't know what they are now with
all of the inflation. They might be
$6.99.
Hopefully, they're less than that. But,
um, these usually are like a buck. And
you can get all kinds of different
colors. And they're acrylic. That's
what's important. So, we want to use
acrylic. It's easy to mix. It's easy to
touch up. Um, it's easy to clean up. And
then you can clear over it with clear
coat. Just spray paint, clear coat, and
it won't cause any problems. So, acrylic
is the way to go in my opinion. That's
just how we do it. So, what I do is when
the paint's wet, it's a little lighter
than how it dries. So, it's going to dry
just slightly. And it's slight, just a
shade, barely a a a dash, just a dash
darker than it looks. Okay. And we're
also, if we just turn the bottle over,
we're looking at the color through this
plastic. So, it's going to make it a
little bit more cloudy than it than it
actually is. Um, and and so that will
look a little lighter, right? But if I
just lay it down on the playfield and
then compare it with my naked eye to the
paint that's on the playfield. Uh, and
then you kind of have to think about the
color wheel a little bit like why that
red does not match that red. What's the
difference? Well, this one to me it's
not as vivid and it looks uh, you know,
maybe it's a little more blue maybe.
Just a little tiny bit of blue so it
moves it that way on the color wheel
maybe. I don't know. Um, but that one
doesn't match very well. Okay, now look
at this one.
It's more of like a purple. So, it's
definitely more blue. You know, red and
blue make purple. So, this one's not
even close. You would never use that
one. However, if you look over here on
the sides, it's a little closer to the
side rails, which are kind of like a
purple,
but we won't mess with that right now.
Okay, this one looks promising.
That
looks pretty good. It looks a little
light, but um
this might be a good one to test.
Don't go by the label. The labels, you
know, you'll see two or three different
colors with the same color label. That
would might work. So, this is called
true red.
Might be right.
This is
berry red.
So berry red's too dark and you know
it's going to dry a little darker than
we're seeing here. So that that ain't
going to work. Now if you're if you
can't get the correct color and you
don't want to mix it or you're mixing
it, you just can't quite get it right.
Lean towards it being slightly too dark
than too light. If you put the if I put
red on there that's a little bit too
light, you'll see it right. So, um, if
it's slightly too dark, you're it plays
a trick on your mind where you basically
just see that as wear, like it being old
and a little worn, and so it doesn't
stand out as much. This is cherry red.
Way too dark
and too blue.
This is tuskcen red. We don't have much
of it left. Also very dark. Not not what
we want.
This is primary red
also too dark. The jukebox is starting
in the other room. YouTube freaks out if
you play a bunch of music. And then here
we have true red again. Is that what we
had before? Yeah. So, we got a couple
true reds. I don't know. That seems like
it's the closest. So, I think what I'll
do is I'll take a little bit of that.
Now,
this probably needs some primer first.
The red's probably not going to cover
it. Red's kind of a thin uh pigment on
this acrylic paint at least. Um but I'll
take a little bit out on a brush. Put a
little dab on the playfield. Maybe we'll
do it up there so we don't make this any
worse than it has to be when it's done.
We're we're kind of concerned about it
being as flat as possible, which means
as few coats as possible. Um because you
can see the brush strokes and stuff. Um,
so yeah, let me try a little bit of this
maybe at the top. Another problem you
run into though is sometimes you get
different fading depending if it's at
the bottom or the top. This is not the
color that it left the factory as.
When it when it left the factory, it
would have been a brighter red, but over
time, and this thing is, you know,
knocking on 50 years old.
Um, over time, the uh the the red
pigment in paint fades, right? So the
whole playfield is slightly more green
than it originally was. The red is
slightly less red than it originally
was. The orange is slightly less red
than it originally was. And so that the
opposite of red on the color wheel is
green. So it makes everything look a
little more green. So sometimes it's
different at different parts of the
playfield. So this area may be more
faded. What little bits left? Um more
faded than that area up there. Now
another thing you can do is you can just
repaint all the red if you want. So, if
we were to repaint
all of the red, well, you wouldn't
notice any difference because it's all
the same color because it's all new. We
may end up doing that. I hate to redo
all of this
tech. Well, I don't have to do that, but
I hate to redo all of this text because
text is kind of tricky, but it's kind of
all gone anyway, but we'll figure it
out. So, let me do a little test piece
of this and just see how close to the
original red this is. All right. All
right. So, I did a little test area and
I think I'm cool with it right out of
the right out of the bottle. Um, the
this has been repainted the new color
and that it is slightly different, but
we're so close. I don't know that I can
get it much better than that. Um, I did
a little bit here, too, but that's only
one coat. This is two coats. Also, it
looks like I don't need primer because
with two coats, it looks pretty good. I
did a couple little spots up here
like that and that.
Folks, it's about as close as I can get
it. I'm not going to get much better
than that mixing it. So, I think we're
just going to go ahead and do the red
with true red. What a beautiful name.
Um, so I'm going to paint in the red
that's missing here. I think I'll maybe
I'll just paint up to the edge and leave
the uh leave the original and then I'll
show you the uh what you can do whenever
you've got areas like this. There's a
technique for that. And we'll just we'll
see how it comes out. I think the
whenever the same thing that we did
before with the orange when we get the
clear on it, I think it it will darken
it just a little bit and kind of
hopefully bring it all together. Um
but yeah, I think I think that's good
enough for us.
Heat. Heat.
Oh,
hey.
Okay. So, what I was what I'm attempting
to do, you can see I'm using this old
pretty crappy brush. What I'm attempting
to do is not put a thick coat on it
because you have this problem if you
watch the previous video where you can
see all the brush strokes.
So, see on the orange the brush strokes
there. So, any difference in thickness
pops out. So, we've got two we've got
two issues going on. So, I'm going to
show this real close up, which normally
I wouldn't want to do because you can
see all the flaws. Okay. So, look what's
going on there on that orange. It's a
mess whenever you get close to it.
Because what you're seeing is you're
seeing the natural thickness of the
paint that's missing.
It's what's creating that line. You
know, all those lines there that's
chipped away the original paint. And
then I've put new paint on top of it.
And you can also see the brush strokes
from my new paint. So the whole thing
just isn't very smooth really, you know.
Um, so I'm trying to combat that by
making the red as thin as possible
because it's such a big part of the
playfield that you're going to see. Once
we get clear on it, you're going to see
every little flaw uh uh sticking out,
you know. So I'm trying to go just as
thin as possible with a fairly dry
brush. And I'm just poking around at the
areas that are that are uh really white.
Like this brush is about dry, right? So
if you just kind of
if you kind of dab at it, it might be
too dry now, but I'm just trying to get
just enough paint where it fills in that
white layer underneath. And then once I
get it, I'm brushing over the top of it
to get all the excess off so that
there's just the smallest amount of
paint on it. Um and so I'm just playing
around with it. If if if I get this
color paint, which is slightly different
than the original, on top of the
original, it's so thin. If I get it thin
enough, you'll see the original color
through it, and it'll help blend it and
make it closer. But personally, I think
it's pretty damn close right out of the
bottle. It's certainly close enough.
It's going to look just fine right out
of the bottle. Um, and I'm going to do
one more coat on some of the areas cuz
some of it's just kind of thin. Like up
here is a little thin. And I want to
make sure that it's at least all one
color and that you don't see the the the
wood peeking through. Right. Also, I'm
I'm kind of getting away with my rule,
like I said, where the paint that I'm
putting on is slightly darker than the
original paint. So, it it hides a little
bit better than if it was slightly
lighter. If I was to put it on thicker
though, I think it might get brighter.
Um, which I don't really want. I I kind
of want it to look a little more dull so
that it blends in a little better. So,
I'm going to keep touching that up. And
then of course we have to worry about
inking the black back in. Um this was
obviously easy enough. I'm not even
going to mess with that. I'm just going
to leave it how it is. And then up here,
most of that wear is actually under
where the posts go. So I'm going to
quickly touch that up, but you're not
going to see any of it anyway because
the post go on top of it. There is a
little bit up there I'll touch up. But
there's just not a ton of red on the
playfield. So that's basically I've got
one coat on now. I'm going to keep
working on this area to get a second
coat where it's thin. Um, and we'll be
ready to letter it.
Dick.
Heat. Heat.
Heat. Heat.
I'll be
Heat.
Heat.
Hey, Heat.
Where you want?
Heat. Heat.
Heat. Hey. Hey. Hey.
Heat. Heat.
Heat. Heat.
All
right. So, I'm going to show you another
technique you can use if you've got an
area like this where most of the colors
there, but there's like white spots all
over it where basically the paint's
missing. Um, if it's falling apart,
there's not you can't leave it like
that. But as you saw on the previous
videos, we scrubbed all this. So
everything that's going to come off is
pretty much came off. So it's solid.
It's just it's got a bunch of paint
missing. So what you can do in this case
is you can take your color that's close.
It doesn't have to be an exact match.
This one's pretty close, but and just
paint over all of it like this. Kind of
blot it on.
Right. And then once you do that, take a
paper towel or I'm just going to use my
finger actually and kind of rub the
extra paint off.
So the idea is
what you're doing
is you're taking the paint off the top
layer of the paint that's still good,
but it's going to leave the paint in the
little areas that are missing. Right? So
let me try this little part right up
here.
So, we're just going to take some paint
kind of sloppily put it on there.
Right.
And then I'm not going to rub it on the
yellow cuz I'm going to leave that, but
kind of just rub away the excess.
So, that that's from Clay at
penrepair.com. um he was the first
person I saw talking about that. I don't
know that he came up with it, but um he
calls it the smear technique, not the
type that the politicians use, but if
you do that, it works pretty good. You
you can see the darker areas. So like
basically everywhere it was white is now
a slightly darker color. Um and it it
hides a ton of wear. So that's why I was
saying that area up there didn't bother
me at all. Anytime you've got that going
on, especially if it's at the top of the
playfield, you will never be able to
tell that was touched up by doing that
because the only place that's going to
have paint left is in the actual Let's
see if I We can do that white line. I'm
pushing my luck doing it more than once
on video.
But we'll see. We'll see what happens.
I wish I had a paper towel here real um
let me grab a paper towel so I can show
you that you can do it with that instead
of your finger.
So, I like these blue like shop rags.
But just be careful with it so you don't
rub it all over everything else. And if
you go too much, you'll take all of it
off. Like I took a little bit of it off
there. But you can see how that makes a
dramatic improvement and you won't see
brush strokes because there's only paint
in the area that's actually lower than
the level of the playfield in the first
place. So, um that really helps whenever
you've got like a big field and you
don't want to repaint the whole thing.
Um, you just want to touch it up.
Heat. Heat.
Heat. Heat. N.
Heat. Heat.
Heat. Heat.
Heat. Heat.
Heat. Heat.
Heat. Heat.
Heat. Heat.
Heat. Heat.
Yeah.
Hey. Hey.
Hey,
hey,
hey.
Hey,
hey, hey.
I don't
think
Heat. Heat.
Heat. Heat.
Heat. Heat.
Heat.
Heat.
Heat. Heat.
Hey,
Heat. Heat.
Heat. Heat. N.
be
Heat. Heat.
Oh,
hey.
Heat. Heat.
Oh,
hey.
Heat. Heat.
Okay, so this is where we're at before
the clear.
So, last time we So, we did a video we
cleaned it all up. Takes forever. Then
we did a video where we did we inked it
in, did the orange and some of the like
the cream color. And then this video and
uh this video we've gotten the red done
and inked in more of the lettering the
black including some more of the cream
color. Um
but I'm about to put some clear on it.
So we'll see if
we'll see if the clear brings this
together. See how the coloring is
slightly different? But ironically, the
color that I painted on kind of matches
the look of it underneath these half
circle protectors that they put on here.
Right. So,
it's one of those things. I think we're
going to get away with it just right out
of the bottle.
Obviously, it needs a lot more work, but
it's getting there. We're I would say
we're
halfway done. Maybe more than halfway
done. Keep in mind too, uh, these look
really rough without all of the plastics
on it. So once we put the plastics on,
so where you've got art here, art here,
art here, art here, art here, art here,
right? It'll look much better.
Personally, I think it's pretty good. My
lettering is my weak spot. And also the
brush strokes that are visible is the
weak spot. Um, the color match I think
is I get pretty good. Usually the
lettering is a little off. Um, and uh,
but I'm getting better at it. I think I
think I'm getting better at it. There's
other ways you can do it. You can do it
with water slide decals where you print
it on a decal, but then you have the
problem where you have to guess at the
font. You know, we're trying to match a
font that already exists. These two were
here. This one wasn't,
you know, how do you do that with a
water slide decal? It can be done, but
it's not as easy as it seems like it
would be. Um,
and then you, as soon as you look at the
playfield, you're going to see where the
decal is.
And that's probably the best option to
do it.
On some machines, they actually make a
decal where they might make like this
whole piece and you just put a decal
over that one whole area with all new
art. But you can tell by looking at it
that it's been done. If you look back on
some of our videos, we did that with one
of our Star Treks, I believe, and we did
that with a kiss that we had. Um, we
just put a decal over all the wear. Eh,
looked all right. I think this looks
much better, although it has its faults
as well. And, uh, the star, of course,
needs more work. That's going to be
yellow. So, we still got the yellow to
do. We still got the cranberry sauce to
do at bonus points if you know where
that comes from. Um,
uh, yellow, that, and the blue.
Personally, I think it's looking pretty
good, though. I'm gonna I'm gonna spray
some clear coat on it to lock in what
we've done. And then um I we'll come
back and I'll show you the end.
Well, I think it looks a heck of a lot
better than it did. There's a sheen on
the playfield now from the clear. So, it
looked you can't tell completely on that
picture, but um and you can see brush
strokes.
With that said, I think we based we we
definitely saved the thing. I think it
was, you know, pretty much done and I
think we've brought it back. Of course,
we still have a long way to go. Um so, I
hope you enjoyed it. Leave your comments
below. We appreciate everybody that's
joined our Patreon channel. If you don't
know about that, we put up a little
whenever we do these videos, like this
video is knocking on an hour long now.
Um, so there's little things in the
video that if you don't watch the whole
hourong video, you're never going to see
like the smear technique thing, right?
You're not going to see the smear
technique. Well, if you don't see the
smear technique, how will you ever know
about it? And you might not watch this
whole video. You might skip around. I
know y'all are skipping around. I skip
around, too.
Um, so on our Patreon channel, we upload
little snippets of stuff like that. So,
it's stuff that's on this channel, but
it's hidden in our vast library of 1,500
videos of me running my mouth for too
long. So, we take little snippets of
some of the interesting stuff that's
topical, like how to do that smear
technique we talked about, and um, uh,
upload that as just a little short clip
on Patreon. So, that's one of the things
that we've been doing. And then also
there's uh like whenever we do videos on
jukeboxes, things like that, sometimes
there's music playing that YouTube won't
allow us to play. So we but on Patreon
we can get away with it. So if you're
interested in that kind of stuff, a
little bit of behind the scenes stuff
and unreleased stuff, but not much. Most
of it's stuff that you can get here
hidden in the videos. But if you're
interested in that, check out our
Patreon below. So we appreciate that and
we appreciate everybody that's been
supporting us on Amazon. There's a link
down below. If you're going to buy
anything on Amazon, use our link. Even
if you even if it's not what we link to,
but if you use our link, basically we
sent you to Amazon. Amazon gives us a
tip for whatever your purchase is there.
If you're going to buy a stove or a
washer or a dryer or something, if you
click our link first, it gives us a nice
little tip for sending you there. We're
basically promoting Amazon right now.
So, uh, we appreciate it. So, uh, hope
you liked it. Tell me what you think
down below. Keep in mind, we still got a
long ways to go. Um, but I think all in
all it's turned out pretty good. My
lettering could be a little better, but
a lot of people, a lot of customers
would never even know. They would never
even know. So, I'm very happy with it.
It's come out probably just a little bit
better than I thought it would. So, I
think we're we're we're heading towards
a seven. I don't know if we can really
even get to an eight with the lettering
kind of where you can obviously tell
that it's been redone, but we can get a
nice solid seven out of it. So, leave
your comments below and we will see you
on the next one. I hope you enjoyed it.