Just HOW Did They Hack This Thing Up? 1930 Majestic 132 Radio Chassis Repair 2

Amateur Repair Time
257 followers
I'm looking through this huge, heavy Grigsby-Grunow Majestic Chassis trying to decide what they were replacing when they hacked this stuff in.... This is Chassis #130 but Cabinet #132 .
Check out our Patreon page, for all of our channels. Contains outakes, concise arcade repair tips, bloopers, repair FAILS, Audio youtube wouldn't allow us to upload, and much more!
https://patreon.com/JoesClassicVideoGames
------------------------------------------------------------------------------------
Ladies and gentlemen, welcome back to
Amateur Repair
Time. Uh, if you watched our previous
video, um, at an auction, I bought a,
uh, Griggsby
Grunow Majestic
132A radio from like
1930, similar to these, right? And we
worked on uh, fixing the cabinet up a
little bit.
Basically, the leg had broken off of the
cabinet because this
receiver is so freaking heavy. This
thing probably weighs 70 lb. Just the
uh just the receiver. As you can tell,
it's completely overbuilt. I can see why
they went out of business. I don't know
what this green yellow stuff is on it,
but I'm sure it'll kill me. according to
some of the people in the comment
section. Um, so I'm going to try to
clean it up a little bit, but it kind of
looks like the thing is in pretty nice
shape. These cans, I assume some of them
are filled with capacitors or something.
So, we're going to uh we're going to try
to work through this thing. Now, when I
went and picked it up, it was still in
the cabinet. The cabinet had fallen on
its side and broke one of the legs off.
Because this thing's so heavy and the
legs got wobbly, they went to move it.
They broke the thing. Uh there wasn't a
bunch of damage to the side of the
cabinet. So I think they must have been
standing there when it happened and were
able to just set the cabinet down. Uh
but the leg broke pure clear off of it.
We fixed that in the previous video. If
you didn't see that, go back and check
it out. So the cabinet is ready for the
receiver to go back in it, but the
receiver sure needs some help. It kind
of looks like a tank. So when I when I
got there, it was laying on its side
just to move the thing. I wanted to flip
it on its top. Um, and I didn't want to
do that with the receiver and everything
in it cuz it weighs a ton. So, I
carefully removed the
receiver. The only problem that I ran
into was with the power cord. The power
cord had a little um grommet thing that
was holding it in the uh strain relief
that was holding it in the cabinet. And
after looking at the cord, I decided,
you know, nothing's lost if I just tear
this thing out.
Uh, it was in pretty rough
shape, so I decided to just go ahead and
take it off so I wouldn't be tempted to
plug it
in. Most of it's all right. See, I would
have been tempted to plug it in,
right? That looks real bad,
but there's nothing wrong with that.
you know, it's just the original cord
and it's in pretty rough shape. So, I
want to figure out as we're working on
this, do I need a twisted cord like this
or can I just put a regular cord on it?
So, but we're nowhere near putting a
cord on it yet. I have the knobs for it,
the original knobs, um, I was able to
remove and get them off safely. Look how
this
turns. Like it kind
of it kind of rolls it
around. So I guess we'll figure that
out. Maybe a tone switch or something.
Or that may be the the onoff
switch. And I suppose this is the
volume.
Light bulb has been broken. Probably
ought to take that out before it shorts
out. You don't think there's any broken
glass on there, do
you? Oh, it's the old type that screws
in. When I work on arcade games, we
actually use some of these. Usually ours
are the bayonet type, but these screw-in
ones were used by the very first
Atari cocktails cabinets, so I might
have some of them, but we'll look it up
and see what model it needs. That's the
least of our worries,
though. Um, I kind of want to look in
here. I believe there's going to be four
tubes in there. There's two little wing
nuts at the top. Let me take those off
and we'll look
inside. So, you can see how overbuilt
this thing is.
Um, unfortunately, Majestic, it wasn't,
the company's name wasn't Majestic, it
was Griggsby Grunow. The the model was
called Majestic. Unfortunately, they
went out of
business early because they just
overbuilt everything. So, it's actually,
from what I hear, very a very nice
radio. They just uh they went all the
way on it.
So, obviously needs a lot of
cleaning.
Um, I don't know. I don't think these
are I haven't done one this old. I don't
believe that those are tubes. Those
are probably Is that how they did the IF
back then? Or is there an IF? This isn't
a I don't think this is a super hit.
This is before that. So,
um I don't know.
Okay, I'm going to carefully put that
back and then uh I'm going to remove the
three exposed tubes just so I don't
damage them and then we'll uh we'll
attempt to flip this thing
over. First tube from out of
here. Now, do you want the good news or
the bad
news? The good news is it's still the
original
Majestic G80 tube.
The bad news is there's literally stuff
rolling around inside of
it. I think that one's
done. So, we're going to need a Majestic
G80 tube.
Second
tube is
a
tonsaw
45 and it doesn't
rattle. So that's
good. I would imagine this is probably
the same. We've got an RCA
radiotron 45.
Okay, so two tubes at least survived.
Who knows if they work? And one is very
damaged. That G80. I wonder if I've got
one of
those.
H Well, apparently that's just a
rectifier. And uh they're pretty common,
so I I had several. I picked a couple of
them
out. If I can find the little
label. There you go.
80. This is an RCA. And this
one
80 National
Union electron tube. It's a NU
Jr. Um, yeah. So, the these
two H
Those might be in the wrong spot or
something. We'll figure all that out.
But, uh, I think there's two 24s and
four 45s and then the 80. That's all
there is. So, I would think that those
would be the four 45s, but
maybe whatever, right? So, I think it
said that there were two
24s that are the final output. You'd
think that would be that, but maybe
not. We'll get all into it, folks. Okay,
so
um these cans are so interesting.
There's these big metal cans on the top
of it all over the place that I'll bet
are filled with
tar.
Um it's all like it's so solid. It's
just incredible. I don't know why they
would build it. that overbuilt
everything that uh those two little
clips there are where I think the
um the
uh and the local or distance switch
went. Okay, so I think it's safe to turn
this thing over. I got to watch this.
But if we bust that up, it won't be the
end of the
world. Of course, that won't come off.
It's all welded and everything. Okay.
So, I'm going to carefully flip it over
so that we can see if we can get in the
bottom panel of it. All right. So,
again, it weighs like 70 lbs. When I
lifted it up, uh you could see where
those two tubes were that it did say
G45, so they were in the correct place.
Wouldn't it be crazy if what was wrong
with it was the rectifier tube was just
screwed
up. All right. But really, we'll never
know because there's no way in hell I'm
plugging this thing up until we get some
cabbage done. Normally, I'm not too
worried about that. But this thing's
old, folks. It's very old. I saw some
people online talking about theirs or uh
this is the model
130
chassis. So, it's in a couple other
radios. I did see somebody talking about
they took theirs, they just uh
um brought it up slow and the thing
worked. Uh but I don't want to do that.
Like I said, a lot of times I I do do
that on the like little ones, but this
one, this thing's going to suck like
three amps. So, this I took this loose
when I took it out of the cabinet. This
is actually where the uh speaker plugs
in. So, it's one of those speakers with
a
uh it has
a separate coil or you know it has to
get power from here as well. So, there's
four pins not two pins.
Um and there is
a cover here. I have no clue what that
goes to yet. We're going to go all
through this thing though. But, um the
schematics are
available. I have a copy of those.
I I just can't believe how this thing's
built like a freaking
tank. I don't know
about somebody's been in it cuz there's
screws
missing, but they're evenly missing. You
know what I
mean? So, I don't
know. But uh yeah, let's see if we can
take the top of the bottom of it off and
look inside of it. Well, I got a first
here, people. This is the first one that
I've done that somebody has hacked all
to
hell. Oh, look what they've done to
me. Good
lord. I don't know. It might be done
right. might be done better than I can
do. We'll see. Okay, so let me let me
see if I can figure out what's going
on. I have no clue what those even are.
Are those
caps or coils or
something? What in the
world? Okay, so see that red wire there?
It's going into that whatever it
is. Good God
almighty. Okay, so we got
those. Um, here are our
controls. And then you have this
large kind of
junction thing on
here. Luckily, there's pretty good
documentation on these, so I already
knew this would be in there. These are
two kind of dog bone, I guess, or
something like that. Uh,
resistors, three, four.
God.
Um, that's going to be the rectifier
socket. This
this kind of plate under there. Oh, you
know what that is? That's where you hook
the power line in. They actually have a
u they have different taps on the
transformer so you can adjust for line
voltage. So, I think there's 115, 120,
125 or something like that. So, that's
that.
Um, one of the big
cans is going to be that. I should be
able to figure that out by whatever
terminals it runs
to.
Another big can there and another big
can
there. So that's the front
can. One of these is going to be a
transformer or something. But again, I
should be able to figure it out by where
the wires run up here because I've got a
schematic of all of
this. Got a lot going on, folks.
Okay. So, that's sides. That's that
side. So, then we have this
side. I don't know what these cans are
up here. There's some little chokes
and coils somewhere too that I've seen
on the
schematics.
So, that's a
can. These are the two 45 sockets.
Um, this is a
can. And
then here are my two four sockets that
are inside that
cage. I have no clue what this is, that
is, or that
is. I'm just going to have to work
through the schematic slowly and just
try to
figure out what everything is. Is this
yellow line damaged or just dirty? No,
it's damaged, isn't
it? So, I might have to rerun
that. Okay, so who knows what that cap
is. And then we
have three of them here going to ground.
This, you know, this obviously was
probably replacing
the filter caps, which originally were
2.2. So, I got to clean all that up.
Good
god. I'd like to know like
where that was, you know, like which one
of these cans was it?
big mess
people. It's a 0.25
25 600
volt. All right. So, I should be able to
check it, track it down with
u with the uh the wiring. Okay. So, let
me get the schematics and we'll look
over that and just kind of get a general
idea of what in the world we're even
looking at. Maybe I can identify some of
these caps from the schematics. Maybe we
can identify some stuff from the wiring.
I don't like all of this freaking See
all the fuzz on it,
too. I think most of it's probably fine.
It just needs cleaned
and straightened out a little bit.
There's one of the missing
screws. That's always nice when you're
finding screws inside of
it. Here's a glob of solder. That'd
probably be fine if it fell around and
like landed like right here. That'd be
all right, right? Probably wouldn't
cause any
problems. What a
beast. So, I just figured out the can
actually comes
off. So, is that
the is that how they worked before they
were super hit?
Looks like this is the type of thing you
just leave
alone. Put that right back how it
goes. So, here is the schematic. I can't
print the thing because of the evil
printer
people. Um, I have a printer that it
updates the firmware like once a week
and then it appears that the firmware
update is just to tell me that my ink's
no good.
And if you uh if you print
constantly on your printer, everything's
cool. But if you don't print for a few
weeks, everything dries up and it
doesn't work right. So if you're someone
like me who only prints something every
couple weeks, a printer is completely
useless because whenever you go every
two weeks to print something, it will
not print. So that's where we're at
right now. But this is what the
schematic looks like. through the magic
of video editing. I can show you
that. So, um, we need to we need to
check through some of this stuff and
just see if
um see if the resistors are in spec and
try to figure out what these three large
resistors are. I I mean capacitors are.
I think they're the A, B, and C down at
the bottom there, the filter caps. Um,
so maybe we'll check into that first.
those apparent according to the bottom
for a 50 to 60 cycle uh uh 50 to 60
hertz you know radio uh they should all
be to
microfarad. So let's see what the the
replacement ones are
labeled. So I took the tape off of those
actually uh it says
0.25
600. This one says 25600. I would assume
that's 0.25. 25 as well. And then this
one
says
point. Well, maybe that's the same. I
was thinking that
said.3. Okay. Yeah, that's another
0.25 600. That is kind of strange. So,
3.25s. And then we decided this
one
was, you folks just saw it, but for me
it's been a couple
days. Another 25600. So we have we have
four of those. Um H. Okay. Well, all
three of these at least go
to I guess
ground. You know, I don't want to assume
anything's ground.
Okay. So, let's look at the schematic
again. Let me see if I can figure out
what those must be. 0.25s and there's
four of them. So, our three filter caps
or what I assume are the filter caps.
The the two microfarad caps are they
must still be in a can. The 0.25s must
be to replace these.3s. But, however,
there are one, two,
three, four.
There's five of them and there's a
04 or a 04. But you know, we do have
that one that's 05 that's visible. So,
one of the one of the 3es is missing.
Ah, what are you doing,
folks? Why would they halfway do it?
Like, why would you replace four and not
the fifth
one? Very strange.
Okay. So, um let me show you another
little thing that I found online that
will help tremendously on
this. This is a wiring diagram for that
chassis. Uh I've only got half of it
though
um that Griggsby Grunow released at some
point. It's pretty good though. It shows
you all of the
resistors, all of those terminals that
we were looking at, and it shows you
where the filter caps are. So, they are
in a can to the side of uh all of the
terminals, and they have a green, a
blue, a red, and a black
wire running uh out of the can. So,
that's our that's our original filters.
Let's see if they're still hooked up.
So here is that terminal. Um and
yeah, green, blue, red,
and I suppose that's
black.
Maybe might need to rewire some stuff,
folks.
But yeah, so
this can here
uh is the
original
filters H.
And these that we were looking
at that there's five of, but they've
only replaced
four all come off of these RF
uh
24s. And this is the
05 that also calls comes off of them.
So, we have one of these that's missing.
Maybe it's in this can.
Luckily, this hasn't been turned on in a
thousand
years. That can is still all seal sealed
up, but it looks like somebody's been
messing with it.
So, kind of a mess, folks. You You radio
folks probably
um probably run into this stuff all the
time.
So, I'm trying to think of where to
begin.
I think I need to order some stuff,
don't
I? Maybe I need to order a complement of
capacitors. I've got some, but I, you
know, I'd kind of like to get some twos.
Here's what I was thinking. So, these
are the twos. If you
look, these run
up out of the can
there to these terminals. So, one of
them here, this was probably the
red attaches there. So, that is leading
down to the
um uh one of the two microfarad
capacitors. And then the
black, which I suppose
is maybe this one. We'll have to figure
out maybe that's green. Um is running to
one of is the ground is one of these and
then the two is one of these. So, I'm
thinking much better than all this would
just be a radial cap attached to
whatever two terminals it needs or even
on this side cuz they're, you know,
connected. Um, and just put the three
caps up here wherever they go and get
rid of
that. Just leave it in place but, you
know, disconnect it. Um, and that would
fix that. And then over here, basically
duplicate what they've done. hopefully
clean it up, make it a little
better, and then hopefully replace the
fifth one as
well. Um, let me see if I can look at
the schematic and figure out which one's
which and where our fifth one
is. Okay, so there is a cap
inside this
RF coil, I guess you would call it.
So, there's a cap in there
uh that runs over to
ground that should be replaceable if I'm
careful. I mean, if I damage this, we're
in trouble. But this is pretty hefty.
But I don't even want to change
anything. You know what I mean? Cuz I'm
sure that's
tuned. All right. So, this yellow wire
is the one that I was seeing poking out
and I was saying that I thought the wire
was deteriorated, but that will be easy
enough to repair as well. You know, just
run a new one and then likely solder it
there and you should be good. So,
um that's one of the caps. I'm going to
look in the other ones to see if there's
more in there. All right. I broke out my
big 100 watt soldering iron.
I usually use this little welder here,
but it's only 70 watts and it's
uh you can use it on some of this stuff,
but whenever you have stuff soldered to
the chassis, you need more wattage. So,
this thing is working great. This is
an American
Beauty
American Electrical Heater Company 100
watts number
3138
Detroit. And that's the little cradle
for it.
I got that at a thrift store with like
10 rolls of solder and all kinds of
other tips and stuff for it for
$12. What are they thinking? I you know,
I don't even know if it's vintage. It's
got the old cord on it, but it's in such
nice shape. I think it might be like a
new one. I think they still make them,
so I don't know. So, I used it to heat
up this
cap block that was still soldered to the
side because the problem that I've got
is all of these wires are heavily
deteriorated. So, I can't leave
that and they've already been messing
with it. So, I
don't So, my next thing is to try to
figure out on the schematic what's what.
I should be able to
tell from this. So, we've got a blue
wire, a black
wire, and two yellow
wires. And I can't Have other ones been
cut loose
already? It may have already had other
wires removed. Maybe they tested it back
in the day and figured out one of the
caps was bad, so they put one of these
in and then left the other ones hooked
up or something. I don't
know. I'm getting rid of it. That one's
going bye-bye. And then there's another
one here. It's going bye-bye. And then
you've got these two which seem to be
different. I guess maybe I can leave
them, but I don't know. So, I'm trying
to work on this first
um coil.
transformer or whatever they called
it. And I was able to successfully swap
the
cap. Um, but I I haven't taken that wire
loose yet because it runs to here. So,
I'm trying to figure out what's what.
So, I'm going to look at it on the
schematic and see if I can figure out
where we're even
at. All right. It's taking me quite a
while, but I think I've got it figured
out
what's wood. All right.
So there is one little So basically
there were three sets of caps mounted on
here at some point. This big can here I
just took off of here, but at some point
there was another one here obviously.
And we've got four caps over
here that have been added
in that are all
0.25. And then we have one here that's a
0.5.
It's soldered to this little
cap that's been cut loose. So, this one
is different from this one, which
appears to be the same as this
one, which makes sense if you look at
the
schematics. So, on the schematic, you've
got a whole bunch
of.3 and one
point, you know, it does say 0.04. Is
that a
0.05 or is it a 0.5
005? Yeah. Okay.
So, let me see if I
can Boy, if I had a flashlight, it would
help you. I've unplugged this. It's It's
cooling
down. So, if you look, the ground is
grounded or one side of the cap is
grounded. the other
side. And this is you got to figure out
the pin
out, but the other
side is going to the screen grid of
these
G24s. So, there's four G24s. One, two,
three,
four. These are the
G45s. All right. So the second
G24 there is a cap running from the
screen grid to
ground. But starting off I didn't know
if they were in the
machine in the order that they're drawn
on the schematic and I didn't know which
was which. So I looked up the pin out
just to be sure. You've got anode,
heater, heater, cathode, grid, and then
there's the other grid, the control
grid, I guess it's called, which is the
cap on the top of the
tube. All right. So, second
tube, screen
grid. There's supposed to be a
04
cap
microfarad. So they've replaced it with
a
05. Clearly that's what this cap
originally was. That's a 04 that they've
taken out and replaced with one. So what
happened was they didn't replace this
one. They left it in. Yeah. So it's
still hooked up. And I'm trying to
figure out which one it is, you know,
cuz I'm trying to figure
out what this is. What this is. This
this
this. Okay. So the easiest one to figure
out is this one right here.
is going
to the screen grid of number three which
then connects to the screen grid of
number
four. So screen grid of number
three connects to the screen grid of
number
four and there's a.3 they've replaced it
with a
0.25. Okay. So then it connects to a
resistor which connects it over to the
screen grid of number
two where the 04
is.
And that is the resistor down there. So
it's
there. And again, I'm not trying to fix
anything right now. I'm just trying to
identify everything to figure out what
in the world they did back in the day.
So this
one is connected to the cathode of
number three to
ground. So 1 2
3
cathode to ground 3 and that cathode is
connected to the number four
cathode. And then it also runs over
here and connects to the volume control
of all things.
And uh that is how it's set up. So
that's that one. So this one a little
more
tricky. This one is a 0.25 going to
ground like all of
them. And then it runs over here. And
there was a big knot of tape here. I
took it
loose. And this is a good one because it
helps us figure something out. So, it
runs there is a cap somewhere that's
probably a.3 that runs into one of these
little cans that we're trying to
identify. It also
runs down onto the top of the
chassis between
uh number four and number three. And
then it also runs back around over here.
Well, I tracked it all down and it's
that yellow wire right there.
coming off that
resistor. So, if you go back to the
other
thing, it's right
there. You can see that it does identify
it as a yellow wire. And it's where
the 5230 ohm resistor meets the 4875 ohm
resistor. See that wire connecting the
two. So, between the junction of those
is where that wire is coming from. And
that solves our puzzle.
There is the junction of that. So, this
must be that
wire. So, it's showing you uh the two
resistors over there. Here's the yellow
wire coming up. And when it comes over,
there's the cap, the
three.
Right? So, that's this cap that they
have wired in. Now that originally,
these three originally would have been
part of this cap that's now
missing.
Um, so that's this
cap and then it it connects to a
resistor which
apparently is between number three and
number four on the top of the chassis.
We'll have to find that. But remember,
we just saw that on the other one. Or
did we? Did I talk about that? I don't
know if I showed that. So, that that
must be on the top of the chassis. And
then the wire will go off somewhere else
to do something else. But look at this.
There are two more wires. One runs up
to this
coil and one runs up to this coil. So,
these two must connect to that.
So, this cap must be connected to those
two. And so, that's it
there. That's running up and connecting
to
this.
Um, where the other one is, I have no
clue, but we'll figure it out.
Um, it could
be. Well, I don't know. I don't know
where this goes.
Right. And so,
this and this must both be connected
together somehow with that red wire.
So those
cans are
these coils, chokes. I don't know what
they're
called. Condenser maybe. I don't know.
What did I calling
them? It's going to be called different
things on every one of them, I bet. All
right. So, that's that. So, I have found
that cap. I have found that cap. I have
found that cap. I found this cap.
Um, so if you look at this, here's the
tricky one. This blue
wire runs to the
cathode of number
two. So here's number two. Here's the
cathode. Bam. It must be that cap.
And then the cathode of number two also
runs down and connects to one side of
the volume control again. All
right.
So this is
a.3 and then there is a black wire and
you would think that would be the ground
but that's not the ground. The ground is
this is soldered to the chassis. So the
ground is the frame of
it I believe. I might have this wrong,
but this black wire is going to the
screen grid of number
one. So the screen grid of number
one connects to
another.3, right? And then there is a
wire that is connected to the screen
grid of number one that runs down here
to
this. Okay, so that's the blue one and
the black one. The yellow one's the
tricky one. So the yellow one is running
up here to this thing that we were
looking
at. And then there is another yellow
that comes out of the same hole and runs
over
here. They have it attached to this
cap to ground
0.25 and then they have it running down
into the top of the chassis. Now we
already figured out that on the other
side of that of this hole there must be
some resistors on the top side. We're
going to check here in a
minute. Right. So, it is running from
one of
these and it appears to be towards the
front end of the set. So, it's going to
be probably this
one. And it's running
uh the yellow wire is running from one
of these to
um a
cap. Must be that
one. The ground is the case. And then
the second yellow
wire must be this. So it must
be the yellow wire comes out of here
into the cap in the case. And then there
is another yellow wire connected to it
inside the case running over this way to
the 500 ohm resistor
um that we think is on the top which is
the other side of this other one that we
already figured out.
So between
here, which runs down onto the top,
and
here, which runs down on that black
wire, onto the top, there must be a 500
ohm resistor. If I check between here
and here, I should get 500 ohms if the
resistor is good. But I'm just going to
look on the top and see what's going on.
So why is the cap right here? It's
because they replaced this cap without
removing it. they just paralleled it
across. So instead of cutting that
wire and then they would have had to
rejoin the wire, they just added the cap
on top of it. I've heard of people doing
that before, you know. So if the cap's
bad, you just parallel one across it,
which isn't a good idea, but cuz the the
problem you run into is the cap can
short, but it could be that these never
short. So who knows? I don't know. But I
think that's what we got going on. So I
think I've got it figured out. So let's
flip it over. And I want to look in
there and see if I can
find a 500 ohm
resistor. So there is a case on the top
of
it. Okay. So here's the first
G24. And this is the screen I mean the
control
grid. So that's
this. And so the wire that comes off of
it connects to the condenser
gang. And then the other side of the
coil or whatever we're calling it, the
transformer, the the choke, whatever. So
all of this
goodness comes off of that
wire. So it goes from there into there,
and that's where we got all that
happening. Okay. Then the second
one, same thing. It comes off. We got
all this goodness coming off that
wire. So, it goes into there. There's
all kinds of stuff
happening. So, the third one is the one
we're thinking of. The wire just comes
off and goes straight to
ground after it goes through whatever
the coil
is. So, it's different. It doesn't go up
in
here. It just goes straight to here. So,
I don't know why, but it there was on
the bottom there's like four or five
wires running up in there, not
just there wouldn't be anything
really. This just goes through
whatever's in there to ground. So, why
are there extra wires going up in there?
I'm missing a 500 ohm resistor. So, this
ought to be in there
somewhere. And maybe this one, too.
No, I got this one. This one. This one's
missing. Okay. So, I don't know why they
would have it hit up in there, but it
appears that's what's going on. We're
going to find out here in a minute with
the screwdriver. Okay. So, the fourth
one control
grid has all this crap coming off of
it, which is all up in here. So, I think
we're right. I think we got it figured
out. So, this thing is held
on with a couple screws. I'm going to
pop it loose and see if I can tell that
there's a resistor in
there. Look at
this. It's just amazing to me how they
designed stuff back in the day. They
spent so much
money. I don't even know if I can get
the camera down in there where you can
see it. Yeah, we'll zoom it. We're going
to zoom it,
baby. So, look at this.
That's like four wires running up inside
of this thing, which is all
potted. And it appears that there's like
a
500 ohm resistor inside of that thing. I
don't know why they would do that. I
don't know if they were trying to hide
stuff so you couldn't figure it out or
something.
um you know, they were all patenting
things and and
um Majestic thought they really had
something going on here. So, I mean,
maybe they were literally hiding
components so that you wouldn't be able
to figure it out and reverse engineer
it. I don't know. But it's it appears
there's a 500 ohm resistor hid inside
that thing. And all this is doing is
going through that that coil to ground,
which is, you know, the case.
Okay, this is the damnest design I've
ever seen. So, here is our weird
hole. There are four
wires. Now, remember from the other
side, it's got the wire going into the
top that comes off the control grid of
number
three. Now, coming out of the bottom of
that pot is the one wire that we knew
went in there. And then the black
wire that's running to our yellow wire
over to our other cap. And I was saying
that I believe there should be 500 ohms
resistance between those two. There is.
It's 774 cuz it's, you know, out of
spec. And then good luck fixing
that. I guess I could cut it out because
some of it doesn't need to be
there. I don't know. We might just have
to leave that. Um and then there is a
third wire coming
out which runs to the anode of number
four. I mean the um yeah the anode of
number
four. And then there is a fourth wire
coming out. That little
one which is soldered to ground on the
chassis. Okay. So there's four wires
going into it. Now look at
this. There's like three people left
that enjoy this. But look people, this
is fun to me. Um, so here is the one
side. That's the yellow
wire. And then I was saying that I I
believe so it's, you know, it's
connecting to our one coil up on the
front. I was saying that I believed uh
the yellow wire then continued on,
right? So it continues on and goes into
that thing. And I'm thinking that there
should be a resistor up there. We
looked. It's not up there. But if you
measure between
here and
here, it's there. It's 774 ohms. So, um,
that confirms
that. So, the wire that comes
out, it runs over
here. Uh, remember it was this one
coming in, right? Well, that yellow wire
that runs out, it runs over here to
here. Remember I was saying that this
and this must be connected somehow with
the red wire. We've got this one and
then the one that comes out of the
bottom connects to here. It's the
missing one. So I they're they're just
running wires all over the place trying
to hide stuff I think. And I don't know
what this
is. It's like a piece of metal with some
wire wrapped around
it and then a bunch of crap on it. That
might have been like an old res like an
old style resistor there, too. I don't
know. But nothing I don't think
anything's hooked up to it
anymore. Um, maybe it's
this. It would be across the pilot
lamp. So, we got we got more stuff to
do, but I think I figured out what these
caps were, you know, and that all of
these are actually correct. They're off
a little bit. They should be three, you
know, but they don't make three, but I I
might do a 33, something like that.
Um, but I figured out what all those
are. These over here, I believe I'm just
going to leave alone. These must
be
these. 01 microfarad caps inside of the
choke. So, this must be the RF
choke. And there's a 0.002
Um, now we still don't
know why
this had another cap on it. That cap
that I that I
replaced. What's up with that? And it's
not this
one. So, I don't know. This cap here.
This is the one I
replaced. You would think maybe it's
this one.
But it doesn't seem to
be. It's attached
here on somewhere on this. So, it's like
halfway up this or something. I don't
know, folks. Whatever. I replaced it. It
was in there. I put a new one in. Okay.
So, next time we'll uh we'll start
swapping some caps. But on this one, I'm
going to have to replace a lot of
wiring, too. Basically, any of that
rubberized wiring needs to be replaced.
Thankfully, most of it's on the actual
caps that I'm going to get rid of. So,
that yellow wire, I'll just run a new
one and I'll replace this cap and that
will solve that the yellow wire problem.
The blue one will be easy enough. Uh
just a cap from here to ground. And then
the black one will be easy enough. Just
the cap from here to ground. And that'll
get rid of a lot of the damaged wiring.
But the red and the the red and the
black wiring that runs over to here,
it's all really bad, too. And that's the
um heater
voltage. But the rest of it's all cloth
covered and it it all looks pretty good.
It's just that rubberized stuff. All of
the caps that were in here they've
already replaced. And the one that was
here they've already replaced. So I
think most of the rubber
uh wiring went bye-bye back whenever
that happened. All right. So there you
go. Hopefully we'll get it fixed and we
can put it back in our beautiful
cabinet. This Have I mentioned it weighs
70 lbs yet? just flipping the thing back
and forth over. It's giving me a
workout, which is good. But, you know,
it's it's heavy, folks. It the this is
not uh this is not lightweight stuff.
They designed this really well. Maybe
overdesigned the crap out of it. It's
probably twice as heavy as it needs to
be. And them hiding resistors inside of
uh uh coils and stuff. They didn't had
Come on. Come on, Griggsby. Be
Griggsby. Come on, Griggsby.
Come on, Griggs. Come on, Griggsby. Be
grunt. You didn't have to do that. You
didn't have to hide the stuff inside of
the potted material inside the cap on
the top of the thing. I I don't know why
you were doing all
that. All right, folks. So, we'll see
you on the next video. I hope you
enjoyed it. Give us a thumbs up if you
made it this far and uh leave your
comments below. Have you ever worked on
one of these? You know, this wasn't the
only radio they
made. Let me tell you a little bit about
this company as we're leaving here.
They went big. They went big, people.
They were making millions of these
things a year in 1929, 1930. They built
this huge factory and we're doing
something
like 5,000 radios a day or something.
Complete radios. And they had all kinds
of of u tabletop versions and stuff.
These are just some of the early ones,
so they're big old boys. But um they
made tons of these things. And uh they
obviously overbuilt them. I mean,
they're twice as nice as they need to
be. And uh at the at the time they had a
reputation for being very nice
radios. And
uh they kind of they kind of lost it,
you know, because the other companies
could design the sets a lot cheaper and
they sounded about the same. And
eventually they went bankrupt, lost it
all. But they were a huge company. So,
for a couple years,
apparently they were the number one
radio company. Um, I had never heard of
them until I got this thing until I saw
it in that auction. I had never heard of
them. Of course, I don't, you know, I
wasn't around in 1929 either, but look
them up if you get time. Griggsby Grunt
Majestic Radios. For whatever reason,
they called all their radios
majestics. Um, and you'll see some of
the most beautiful radios you've ever
seen if you do a little googling of
that.
