We bought a Bally Supersonic somebody caught on fire, and we're putting it back together one board at a time. Next up: The solenoid driver PCB, we're going to build one out of parts.
Check Out Our Patreon Account, for Unreleased Repair FAILS, Concise Repair Tips Not Possible In This Long Form Video, And 1 on 1 Repair Assistance with YOUR Project!
Thank you to everyone who has been supporting our channel! If you use the link below before you purchase anything on Amazon, we get a royalty for sending you there, thank you!
Our store is located at 139 Caldwell St., Rock Hill, SC 29730.
Ladies and gentlemen, this is Joe's Classic Video Games back with another cool pinball repair video
for you this evening. We got in this Bally Supersonic pinball machine from our buddy Jonathan
and we did a video on this before, a couple days ago, where we figured out that the game
had a short on the MPU that sent 43 volts through all of the 5 volt lines. So everything that was
supposed to get 5 volts got 43 volts, which is catastrophic. So it blew chips up,
caught things on fire, everything else. Every board in the game appears to be
damaged, probably fatally. Two of the boards were already missing and the rectifier board survived.
But the MPU is cooked. The sound board appears to be cooked and we're not sure if the displays
are cooked. But at the end of the previous video, we were able to get the thing where it's at least
powering on now. So we've got the GI lights working and that's it, of course. This thing
is in pretty rough shape and we had people say, oh it cost too much to fix. Well, I think we can
do it pretty inexpensively. We're going to see what we can do. But here is our power rectifier
board and our transformer. We're going to go ahead and work back through this thing. The next thing
that we need to do is put the solenoid driver board in it. That's where the power goes next.
So whenever I work on these, this thing's a complete basket case. And it literally was
catching on fire, burning things up. You can see the sound board's still in here.
You can see some of the damage there. But whenever I fix things, even if it's just a minor thing or
if it's just a complete basket case like this, you just start at the wall and work your way
through. So we had to literally repair the plug that plugs into the wall and put a nice new one
on it. And then we had to repair the rectifier board. We eventually found the short that was
on the MPU that we've removed. I've tested the voltages on the rectifier board and they're
correct. But we noticed on the previous video too that this connector on the bottom here did
the usual thing where it burns up a little bit and they repinned it. But they put some of the
wires in the wrong spot. Now luckily they were all just grounds. So they moved some ground wires
around. I don't like that crap. So I've got to repin that connector anyway. So I'm going to move
them all back. So I'll show you how they had it and then I'll show you it after we get it repinned.
So this is the connector and they have done work on it. You can see where this one's been soldered
and this one actually goes down here somewhere. They've got some stuff moved around. Again,
we looked it all up on the previous video. It's all ground wires. So instead of the ground wire
going here, it's going there. But I don't like that. So I'm going to, I've got to replace this
anyway because this connector is burnt. So I'm going to put a new one on it and put the wires
in the proper place. Let me show you where you can get these connectors and these pins if you
have this problem yourself. There's a newer website that's been really good on this stuff
and makes, kind of focuses on pinball related components. So there's a website called Wirebot
and the web address is wirebot.xyz. Check out the Dave Ramsey show while you're at it, I guess.
Wirebot.xyz. It's a great, great little company. Little mom and pop company. Your pinball wire
electro dispensary. Shipping daily from Madison, Wisconsin. So he sells all this stuff and it's,
you know, he's a pinball guy so he knows what you need. Now that particular connector is a 0.156
pitch connector. That's the spacing between the contacts. And this is pretty normal. This is
almost every contact. Everything in a pinball machine is going to be that. There's a few
different ones but that's most stuff. And you see he sells everything. So if we need that new
connector that burned up, it's a 20 position connector. I know he went through a bunch of
hell trying to find this exact connector. It's 62 cents. See what I'm saying? This is the place you
need to go folks. So go check it out. He didn't pay me anything to tell you that. I'm just telling
you we need to support these companies that cater to the pinball market. He's got a bunch of other
stuff too. Harnesses and wires and stuff like that. Tools. You might as well check them out.
Okay, so I have repinned the one, replaced the connector and all new pins. You can see how much
better they look compared to the original ones that we've cut off. And one thing that is important
see if you can get this little plug or make a plug. So there is a key they call it where one
pin can't go in. And that pin is missing on the board and it's so you can only plug this in one
way. You can't even plug it in off one pin. It has to be just right or it won't go in there.
And that'll save you from all kinds of problems. So we've got that one good. Very happy. And now
I'm going to repin the other two. Those two connectors you don't have to replace usually.
You just have to put new pins on them. On this one, I think the reason that they switched the
wires around, like I mentioned, they were all grounds. So they didn't put them in the wrong
place per se. They just moved them from ground to ground. I just didn't like that because it
didn't match the schematics for down the line. But I think what they were doing was since these
two were burnt up because the AC was running through it. That's what the general illumination
runs on. I think that what their point was to move those two grounds somewhere else that didn't,
that wasn't burnt up on this connector. So they just moved the two grounds from there,
one of them down to here and one to wherever the other one was, somewhere in through here.
I just don't like playing that game. So we've got them all back where they go. And I'm going to go
ahead and repin the other two connectors while I'm at it. All right, so I got the guard back on
there. I got all new pins and all three connectors. It is good to go. And by the way, this one, it's,
you know, it's white because it's brand new. Believe it or not, some of the new ones look
like this too. They call that the natural color of nylon. And then this is, I guess they put some
kind of chemical to bleach it in there to make it look white. So yeah, those look old, but they're,
you know, the new ones look like it sometimes too. So I don't really care about that anyway.
Look at the rest of it. Did I show you the rest? Look at the, did I, you looked at the, okay.
All right. So before we get to any of this cosmetic stuff, I know this thing's a basket case.
We have to get these electronics right. So on the previous video, we showed that the 43 volts
was shorted to the five volts. It fried everything. When we bought it, it was missing the solenoid
regulator board and it was missing the lamp board, presumably because they figured out that
they caught on fire or blew up or something, right? So this solenoid board is the next part
of the powertrain. So the power comes in, comes up to this rectifier board, is rectified. So when
you rectify a voltage, you turn it from AC, which is what's coming out of the wall, into DC, which
is what this board is doing. There's three bridge rectifiers on there. And then the DC voltage is
used to run everything in the pinball machine. There's also an AC voltage that runs the general
illumination lamps, like I mentioned. So the next thing that happens that we need to get this thing
to work is that the 12 volts, which is an unregulated voltage, but a rectified voltage,
so it's 12 volts DC, give or take three or four volts. It's not even close usually.
And it comes up here to this solenoid driver board, which I'm showing you even though it's not
there, but it goes right here and it comes through this connector right here. When it gets on this
board, the 12 volts is turned into five volts. And five volts, as you know, or you probably know,
is the voltage that at least on these antiquated electronics is what ran all of the IC chips. The
newer ones run off 3.3 volts and I believe there's some other voltage they use now.
But this old school one needs 12 volts and it needs five volts. And that's pretty much what
runs everything. Now there's another voltage that comes off of here that is a high voltage of like
190 volts, or I think it starts out at 230 volts DC, and it's turned into 190 volts, which is what
these displays used to run. So this board has a five volt power supply, 190 volt power supply,
and then the whole bottom of the board is used to control the solenoids. So they were basically,
this is the MPU, this is the lamps, this is the solenoids, and then the two power supplies,
and then the rectifier board. They were basically trying to keep the high voltage stuff, the powered
stuff, off of the MPU. Except for that one little line that went to it and was what fried everything.
So my whole point, next thing we need is a solenoid driver board. Now they make them brand
new. They used to be about 100 bucks. They're probably 150 bucks now. But so you could just
buy a brand new one and there's certainly lots of good options. Since this is a video
where we're having fun, I'm going to try to piece together an old one. I've got several in a box,
but I've been picking through them and picking through them and picking through them, and I
think I'm down to just the junk. But we might be able to take a junk board or two or three
and make one working board out of it that we can put in here, as long as it'll be reliable.
We don't want to make a piece of crap. But I should have at least a board that needs a lot of work
that we can put together to put in here and get a nice solid five volts out of it and a nice solid
190 volts out of it. What do you think? We'll try it. So let me see my stash. That's the problem
with, you know, picking things out of your stash of used parts is eventually you get to the point
where you don't really have any good candidates left. But we'll see what I got. This is a 1979,
I believe, Valley. So we need something that vintage. Now any of the old Sterns or old Valley
games all use the exact same solenoid driver board, so it doesn't have to. It doesn't really
matter what year it's from or anything. All right, so I have pulled out some of my stash. I'm trying
to get the desk cleaned up. We talked about that in the previous. It's getting there.
There's room. We're getting there. I've just got to work that one. Okay, so solenoid driver boards,
I have six of them. Let's see if any of them are even close to usable. What do you think?
I've also got some sound boards here that I can use on the sound board,
and I've got tons of lamp boards. Okay, so this one looks pretty rough.
Yeah, it's not a great one to start with because all of the chips are gone. Now there's only four,
but they're missing. If we have to, we can use this one. It's just, you know, what do you want
to start with? Maybe eventually I will have to use this one in one of them. It's missing the
flipper relay. It's missing several of the transistors. Now why would those be missing?
Somebody's been pulling those off and using them on other boards probably,
and it ain't me, but it does have the heat sink that might be useful for like this one.
So this one actually won't work. This is a solenoid combo board.
This probably goes in a Bally Baby Pac-Man. That says 83. Baby Pac-Man was a pinball game,
and it was a video game, and I think if I remember correctly, it had a combination
board like this. So the difference between this one and the regular one is that the high voltage
area isn't there because they're not actually running displays. So on Baby Pac-Man, it doesn't
have plasma displays on it because it has a television screen. So it can display your
score on the screen. So because of that, they didn't need this area of the board,
which opened up this area of the board to run the lamps. So by creating this board,
they got rid of the lamp driver board by putting it on the solenoid board,
and they still needed the five-volt regulator. So that won't work in this one,
but it'll work in a Baby Pac-Man if we get one. All right, let's see about this specimen.
It's missing two chips. Oh, I thought I heard something. We're testing a jukebox.
You'll see that on the Joe's Jukebox channel eventually. So this one's missing two chips.
These chips, I don't know that I've got new versions of these chips actually. Let's see
what they are, if I can read one. It's got that thing that they did where they put a part number
on it instead of the chip part number. So anyway, it's missing two of the chips. It's kind of rusty
looking. It's filthy. Yeah, it could be repaired. We might not have anything any better. It's
getting low, folks. The pickings are getting slim. Okay, so this one has caught on fire twice.
It's rusted all to crap. Looks like it floated up on the beach somewhere. Hey,
but it does have all four chips. So that's good, right? Yeah, I don't like this one at all.
We're down to, there's only two left, folks. I told you the pickings are getting slim.
All right, so this one, the regulator heat sink is missing. All four, ow,
should have known that was going to happen. All four chips are missing. All this actually looks
pretty good though. And all of the display stuff, a lot of it's missing. The two transistors,
resistor, diode, the big cap that goes up here is missing. And the flipper relay is missing. So this
one, not so much. There's hardly anything left here except the board itself. And you know all
these, but that's not that big of a deal actually. You can replace all them. And finally, and I
didn't plan it this way, we have this one. So this one's dusty and it's missing the big chip,
but I think I have those new. It has all of its transistors in the little cap next to the
transistor, which again isn't that big of a deal because I've got new transistors,
but there's a lot of them and it would be better if they're there than them not being there.
It has a little, I assume that's a Brady tag. Let's see if we can read it.
I cannot read it. What does it say? Who is that? That's not Brady. Oh, it just says plastic
locks so that it's not anybody. It's unbranded. Usually it'll say Brady Distributing,
which was our local pinball distributor that did a lot of the repairs back in the day. So they would
put a little tag on something they had repaired with a number on it so that they could prove
that that was the same one they'd already worked on for warranty purposes. Okay, so one chip
missing. The display stuff, a little bit of it's missing, but it's no big deal. We'll get into all
that. This is going to be replaced. That heat sink goes here along with the transistor, but the heat
sink you saw on the other one. And this is nothing over here. I think this is the one, folks. What
do you think? I think this could turn out to be a pretty good little board. Let's make sure the
back's not destroyed. The back is fine. So there is a trace here that's been repaired. So these
transistors down here, some of them go to a couple different connectors, but maybe that one doesn't
at all. Let's see. So the trace went through here. It burnt up and went up to here. Boy,
they should have cleaned that up a little bit better though. You see that? It was just all
ribboned around where it was touching other stuff. All you got to do is mess with it a little bit,
like I just did, and it'll pop right off. Okay, so we'll look up and see what burnt up on this
particular board, but it doesn't matter. They've actually done a decent little repair there. Now,
you could have routed it right along the trace. It would have been cleaner. And put a little
rubber cement to hold it in place. It would have been a slightly better way to do it.
But I think this will work. We'll make sure that's a good connection.
So yeah, everything looks actually like it hasn't been touched with the exception of that trace
that completely burnt up. So I think this is the one. So it'll be good to get it out of the parts
box. I don't know where I got it, but somebody took it out of the machine a long time ago,
and we're putting it right back in. I get so much satisfaction out of taking these old parts and
putting them back together. If you've ever watched my other channel, boy, it is storming out there.
This is like some... We've got some Five Nights at Freddy's stuff going on on the security camera.
On my other channel, Amateur Repair Time, a lot of times I'll work on clocks,
and I love buying clocks that have been parted out and then trying to find the part to put it
back together and get it working again. Tick, tock, tick, tock. That's so cool. Love it.
But if you go on eBay and look at like clock parts, you'll see they'll have like
Seth... It'll say like 1910 Seth Thomas cabinet or clock case. And then the next ad will be 1910
Seth Thomas clock movement. And then the next ad will be 1910 Seth Thomas clock face. And then the
next ad will be 1910 Seth Thomas clock hands. They're literally just taking the entire things
apart quicker than I can put them back together again. But it's a fight I'm willing to take.
All right, so the first thing I'm going to do is clean this off a little bit. I'm just going to
dust it. I use like a little paintbrush to do that. Just a little, you know, inch and a half,
a cheap little chip brush, and just use it as like a feather duster almost to dust it off.
And then if there's anything really dirty, you can get it a little wet with some Windex or
something to clean it up a little bit. And then I'm going to look and see if I've got this chip.
That'll be the first thing that we mess with. So we'll do that and then we'll check these
transistors. Again, there's three boards here. So this is what drives your solenoids. We really
don't have any way to test that at the moment because we don't have the main board in there.
Right. And then this part up here, including this,
is your 5 volt regulator. Turns the 12 volts into 5 volts. That's all it does.
And then this part here creates your high voltage for the displays. It gets in 230 volts and these
three transistors regulate it down to whatever you set this little knob to. There's also a
relay which is just when the computer turns on one of these transistors, one of them turns on
this relay so that your flippers work. So it's kind of just thrown on there. All right. Let me
clean it up. I forgot to do the bit about taking my watch off. Just wait till I get my watch off.
Now I got that out of the way. All right. So I cleaned it up a little bit and I took off the
cover from here. So we're down and we're going to focus on this first.
I got these straightened out a little bit. It doesn't matter. I'm going to put a little
socket in here. It is a 24 pin chip and it is a 74154. Man, I do have them brand new.
New kind of old stock. Look, it says November of 93, that bottom date code. So 74154. Here is the
part list from a manual, a valley manual. U2 is a 74L154, but I think a regular just straight up
74154 will be all right. And here is the drawing of that of our board. This is actually a Xenon
manual. You see up here it says AS251822, which is what ours is.
But it also says, if you look, it says replacement for AS251816. And down here it says note
interchangeable with 251816. That was the older version. It's basically the same thing, but I
that version has hand drawn traces on it. It's just old school. Just putting stuff like 8-ball
probably. Okay, so I'm going to put the socket in, go ahead and install our chip, and then we're
going to test all these transistors. Again, we can't actually use this part of the board until
the MPU is working, and we're not doing that yet. It's actually waiting for us over there.
So let me get that out of the way and we'll test these. All right, so I got my socket in,
got the chip in, and now I'm checking all of these transistors. This one that has already
been replaced at one point is testing. I didn't do this, but whoever did it.
It's testing a shorted. So the way you check them is you check and see if the middle leg
is shorted to one of the outside legs. This is just a quick and dirty way of checking a transistor.
And you kind of can do it either way and then figure out which way gives you a better test,
but what I do is, let's see if I can chopstick it here. Yeah, so the black lead is actually on the
middle. There goes the jukebox again. The black lead is actually on the middle pin, as you can
see, and then the red lead is on one of the top legs. And we're getting 0.510. Oh, it might actually
play one. Nope. The CD box only has two CDs in it, so it can't play anything right now.
Then the other is 0.478. So those are not shorted together. If it was below about 0.2,
I would consider that shorted together. If it's between 0.4 and 0.7 or so, it's just a regular
voltage drop like it's supposed to have. Let's see if I can chopstick it and show you what's going on.
These two are shorted together, but it could just be sloppy solder. So you see how this black one
is actually on the middle pin. I'm just on that other trace, I mean the other end of the trace,
and then the red one is on the bottom pin. They're shorted together. So it could be that
the transistors burn up, or it could just be that they're connected. Let's see if we can tell.
So how do you know, right? Like, how can you tell if that's actually connected? It kind of
looks dirty. You could just drag the soldering iron across it, but let me show you a quick little
trick to tell. Well it works on some boards, some it won't depending on what's on the other side,
but if you put a bright light under it, under it, not on top of it. So if we like
move some of this out of the way, if I don't break them all because I've been playing with
them so much. Okay, so now that we have that under there, look at this. Look at this. So look at,
look at this one. Is that middle pad connected to the bottom one? Well, hell no. You can tell
clear as day with a light under it. They're not even anywhere near each other. But what about this
one? Yeah, they're touching. It's just sloppy solder. They just soldered the middle one to
the bottom one, and that's their repair. I mean, come on people. You can't. People, they're touch.
If there's, people are supposed to be like, you got like that. Don't do that. They're like that.
Come on people. You can't. They're, come on now. That ain't how it's supposed to be done.
So it's still kind of sloppy. I'll clean it up a little more, but basically I just drug the
soldering iron through the middle of it, which reheated the solder that was touching both sides.
And then when the, you know, the solder, when the iron gets all the way through it,
the blobs will tend to go back to the, the, the trace that they're supposed to be on. You can
also just remove all that and reflow it, you know, because there's probably a little bit too
much on it. But we'll retest it to make sure that that one's all right. So after I removed the short,
it was still shorted. So why would that be? Well, it's because you've been running it like that,
you know, so it's, it's, it permanently screwed up the transistor. So I have put a new one in here.
I'm about to clip the leads off and make sure they're not touching and then test it to make
sure it's all right in the board. Sometimes when you have one of these shorted, it's going to mess
up the transistor. I mean the resistor and the diode that runs to it as well on the other side.
So we'll check that to make sure everything's all right. But hopefully that will finish that.
And while I'm on the back of it, I'm going to clean up these pins and re-solder all of these
too. These get bad solder joints on the end. Like see how that one has a crack around it?
So that pin has physically broken loose
from the solder on the board. So it's going to, now that one's not even connected to anything,
but it's going to randomly allow the electricity to pass and randomly it won't. So you need to,
we need to clean that up. Also, whenever they do stuff like this, you got to watch that they
haven't left the solder long where the wire can lean over and touch the pin next to it.
Remember we just had the same problem on the MPU where the 43 volts shorted to the 5 volt right
next to it. So I'm going to clean all those up and give them a nice little touch up of solder
to get them nice and reflowed. And then we're on to the 5 volt section. All right, so I'm happy
with that part of the board. Everything's cool. The transistor that we replaced tests fine
in circuit. So we're going to do the, the regulator. Now it looks real bad,
but really all that's missing is the regulator transistor. And then there's a couple of screws
that hold it in place and that big heat sink. But remember we had this one that has just what
we need loosely mounted on that board that they've already stolen the regulator from.
So let's see what they call that regulator. Q20. Q20 originally was a
78H05KC or LM323 or LAS1405. The LAS1405 I've never seen. Now the 78H05KC, that H is very
important. If you put a 7805, it's like half an amp or something. And the 7805 is like four amps
or something like that. So if you get one, make sure you get a 78H05. It's very important. Or
you can put an LM323 in it. It's the difference between like half an amp and three amps or
something like that. Okay, I did that. I did that in a video too. That's part, you know,
we've got that new Patreon channel that we started. I'm trying to make it where Patreon
doesn't have anything that's not on this channel because I want everybody to see everything for
free. But like I just said, we did a video one time where I looked all over the difference between a
7805 and a 78H05. But which video was it? I have no clue. I don't remember. I was working on one
of these, but I don't remember exactly which game it was. So that segment, if I had just that
segment, that would be really cool. I could just splice it in here and we could talk about it
again. But I don't have that segment. And I don't remember. I don't remember what the difference
was, the exact amperage. And I don't remember what game that was on. So that's what we're doing
on our Patreon channel. We're finding little pieces like that where there's just a little
segment where we, like that thing I just showed with the light shining through the transistor.
Just that little part. We'll take just that little part and put it up on Patreon as a special little
thing of a separate video that just says, hey, here's how to tell if something, here's an easy
way to tell if two traces are shorted on a board. Put the light under the board, right? I just showed
out one little piece and that's a little clip for Patreon. So it's something that you can watch,
you know, on this channel. But they're all hidden. I've probably done a thousand little
little tidbits like that that are all hidden in all of the videos. So as I find them, I'm going
back through our old catalog and looking through the old files and the old videos.
And as I find a little piece like that, I take it and I put it on Patreon. So if you haven't
seen that, the link's down below. You might enjoy Patreon. All right, so let me try to find a
78H05 or an LM323 and let's pull that sink off of that one and see if we can get it all mounted in.
Okay, so we got that mounted on there. It's a 323K with a nice healthy amount of
heat sink compound. Just a little bit, you know, you don't want to overdo it.
We got that back. Look, it's starting to look more like it's supposed to look now.
Next up, we're going to change this cap. This cap is old. It is a 11,000 microfarad 20 volt cap.
It's a, it was made the 34th week of 1978. So it's done its duty. We're going to let it retire.
Supersonic, it only has two flippers. There's not a ton going on on it. So you can,
it can run off like of the 11,000. It can probably run off 10,000. It just has to do with,
that's the filter capacitor for the five volt, which sometimes whenever you
thump the flippers, it draws back through everything and blah, blah, blah. So anyway,
if you've got more than two flippers, that needs to be a little bit higher. I don't,
they may have made that higher in some of the boards later. That's, that's from clay
at pinrepair.com. He always talks about that. So we always put a 15,000 in them, 15,000, 25 volt.
And the, the, you can, you can go down to like 10,000 or up to 15, maybe a little bit more,
but you don't want to get crazy because it starts putting a strain on the regulator or so I've
heard. Right. But we're going to go ahead and swap that cap out. If you don't, you might get
where your five volt fluctuates or even has like some AC ripple on it, which you wouldn't think
that it would this far past the rectifier board, but there's no cap on the rectifier board. This
is the filter cap. So it's just, it's good practice to replace this, but you'll get the
game resetting and things like that. If that cap starts giving you problems. So we're going to do
that. And then there's one other little thing. Well, there's actually two other little things
and we're just working the five volt section right now. One thing is this capacitor is physically
damaged probably just from being stored in the box. That's a 0.1 20 volt, otherwise known as
about the most common capacitor ever. So that's a 104 20 volt cap. So I'm just going to put a new
one in there. I don't think I've got any of these disc ones, but I've got some little ceramic barrel
ones that I can put in there. So I'm going to replace that one. I might have a disc one. The
newer ones are a lot smaller than that. A little tiny cap this big is the same as that one.
So I'm going to replace that one and I'm going to replace this. And then there's a resistor over
here. I want to show you. All right. So we've got our new cap man with zip ties soldered together
and we've got a replacement cap here, a 104. That's a 0.1. So I'm going to show you
two other things. Actually this negative right here, it runs under here and it came next to a
pin over here. But if you simply tie that negative to this trace right underneath it,
you're tying the negatives on the board together and it gives it a better connection to all the
other boards. So right now the connection to the negative of the logic is through one pin.
If you tie it to this other one, it's through a whole bunch of pins.
I'm sure they did that for a reason, but it's been kind of accepted practice to,
instead of having all of the negatives run off from separate places, to have them all tied
together over and over again. Because you don't have a sound thing to worry about. And on the
soundboard, I guess it's a different issue where you might get a ground loop or something. But
it's going to help with all kinds of things. Flickering displays, blah, blah, blah, blah. So
it's just something we like to do. So I'm going to pull this back a little bit and put a little
jumper between there and there. And then our ground will have all kinds of connections to
the other boards instead of just one little puny connection. And then the last little thing that
we've been doing lately, this is the five volt regulator section. This is what we're working on
right now. And so this chip that we're working on gets 12 volts in and then it puts 5 volts out.
See how it says plus or minus 0.25 volts? What's going on is this voltage is going to be a hell
of a lot higher than 11.9. It just runs that way anyway. And with the transformer tapped for 115,
we didn't change that. We probably could have changed that whenever we had it out here on the
board. But with the transformer tapped for 115, the wall voltage around here at least is like 124.
So all of these unregulated voltages are higher. And these regulators, as they get older,
they tend to have the output go a little higher too. So on almost every one of these boards,
now technically the regulator should turn it into 5 volts no matter what the input is.
But it just doesn't seem to work like that. So one of the things that Bally did was they
added this little resistor, R49. This connection, if you look at the data sheet, should just be
the ground as the usual connection, right? They've got it running through a 2.2 microfarad, no ohm,
2.2 ohm resistor. And then they've got this little resistor. So it's tying the output
to here. And it has the effect of lifting the output voltage. So if this voltage is much more
than 5.25, if you cut this resistor out, it will lower that voltage down. You don't really want
that being like 5.5 and 5.6, which I've seen a bunch. So it's pretty good practice to just remove
this resistor. And by doing that, usually you will end up with between 5 volts and 5.2 volts,
which is right where you want to be. That's been my experience. Now I just put a brand new
transistor in there, so I'm not sure if it's going to have the same problem that some of the older
ones do where the output lifts up a little bit. So I think we'll just leave it the way it is for
now because that's easy enough to cut out while it's in the game. You just reach over and literally
snip it out of the board. It is that one. Yeah, so that's a 100 ohm resistor. So if you snip that
out of the board, it will make the voltage, the 5 volts go down. Okay. Alright, so that's it for
that part of the board. We are moving on to the display part. So it needs a fuse holder, and I
need to test these three transistors to see if any of those are shorted. And I need to replace
R15. So let me see what I can tell is messed up. It all looks pretty good.
And I'll come back. Okay, so all three of the transistors test fine. That resistor was missing.
That's a 100k 1 watt resistor. I had to steal it off another board because the ones I have
are only half watt. They would probably fry if I left that in there. And then the legs, since this
resistor is so old, old carbon resistor, they wouldn't fit through the board. So I put little
jumper legs up through the board and then soldered it to the little jumper legs. Look folks, don't
worry about it. I put the extra fuse clip in. Now this is a little baby fuse. A little baby.
It's supposed to be 3 16ths of an amp. Don't put like a one amp in there. Don't do it.
You can do like I did and put a quarter amp in, but don't put a one amp. Yeah, so that's it.
I mean this thing, oh yeah, I replaced this little potentiometer here. That's a 25k
pot. Those are known for going bad. They suck. And so if you've got flickering displays, if they come
in and come out, they turn sometimes don't come on, it could be this thing. I had the honor of
having one of the guys that used to work at Bally comment on one of my videos a couple weeks ago.
And he said that they did extensive testing on this. And in the manual it says 190 volts
is what the display should work on. And they did a lot of tests, he said, to come up with that
exact voltage. He said he personally felt like 180 was a better voltage to run them at.
If you run it at 170, you start having problems. If you run it at 190, I think he said that
if you run it at like 170, you have regulator problems. So you're going to start burning these
up. But 190, you get more burnt glass. So 180 he thought was a happy medium. He felt that 180 was
the best voltage to run them at. And you can adjust that with that pot. Now there are two
test points. One shows you the voltage in and one shows you the voltage out. I think that's
the voltage in and that's the voltage out, one or the other.
So I'm going to put that little piece of plexiglass back on it and then guess what?
We're done. It's ready to put it in the machine and then test and see if we have our 5
and if we have our 180. I have plugged them in. I have installed our board. These things get so
bent. I don't know how. I guess just messing with them on the board. I have installed our board.
Look how beautiful it's looking. Now you know you could get a brand new one like I said.
I took the shield off so we can measure those voltages. You can get a brand new one like I said
but I kind of like how the old vintage ones look. Nothing wrong with the new ones but you know part
of the reason I like messing with these is because I like old things. It's just cool to me
that you can get that board to work again. So let's turn it on and measure our voltages.
So we're looking for fuses blowing up like the high voltage. I can reach the power switch.
Didn't see any fuses blowing up. I have unplugged all of the displays
because they're everyone I'm suspect. I've also unplugged the sound board. It's definitely suspect.
Okay so all of that for two voltages. Let's see if they're there. I've got a multimeter here
given to us by Todd. Thank you again Todd. Todd stopped by a couple weeks ago.
He made it to good old Rock Hill. Let me see how dangerously I can do this.
Oh that's hooked in there pretty good.
It's gonna be fine people. Everybody gets so serious. Not everybody. Some of you.
All right so this top one up here is the 12 volts coming in.
15.76 like I thought. So it's always high. All right so this one below it is our five volts.
5.027. So we did a good thing not cutting the resistor out of that board
because with a new regulator it's completely capable of taking about any voltage that it
gets and turning it into a pretty close to five volts. And then that little resistor
is lifting it up a little bit and it's 5.02. Perfect. All right so that's there. So now we
need to check our display voltage. This one's a little careful. You gotta be a little careful.
It is you know 100 volts. 263 is coming in. Oh that's high. And then going out is
Lord don't let me short nothing. 185.5. Let's try adjusting that more towards 180.
Now the original one you could just do with your hand. But the original pot.
I don't know if I went the right way. 178.5. That's probably close enough but hey
since we're on camera why not tempt fate. I don't even know if I moved it.
178.7. Close enough. We'll just leave it at that. All right so there we go. Let me put that shield
back on it so you can get the whole shebang. All right so there's the original shield back on it
you originally had a little sticker up here that said caution don't touch this it'll kill you.
But that's long. It probably fell off when the last guy got the hell shocked out of him. Okay so
our next video we are going to try to fix the MPU and I was thinking about it. I think I'm
going to try to fix the one that like blew up all the chips. I don't know if I can. I probably can.
We'll just take it slow. Yeah I'm going to go slower than I usually go. Boy you'll love that.
Maybe I can make like a five hour video instead of a one hour video. But yeah so we're going to
do that. I was just going to try to cobble another one together but that one was actually
in decent shape as far as the battery damage. And it's really not that big of a deal. I mean
like the ROMs we've got to replace anyway. You know the chips that are socketed we probably don't
have to replace the sockets. I think we can do it. We're going to try it. Should make for an
interesting video. So we'll see you on that one. Hope you enjoyed this one. This thing is coming
back together slowly but surely. So I mentioned on the previous video that this game was the original
Valley Star Trek but it wasn't really Star Trek. It was a knockoff called Starship or something
like that. Right? I think it was Starship. Something like that. So the original version
of this had a back glass with a fake Enterprise on it and Valley was basically going to make a
fake Star Trek game. And so that's what this was. Starship. Right? And the guy that designed this
table, he had just designed Wizard and he had just designed Captain Fantastic and then he
designed this and this was going to be a fake Star Trek game. And then they got the real license to
Star Trek. And so they could have just made this title Star Trek but they kind of wanted to spread
the love around between their designers for I'm sure financial reasons or there was some reason.
And so they decided to take this game that was a Star Trek knockoff and turn it into something
else. And so the guy turned it into Supersonic with this beautiful back glass. One of the best
back glasses of the early Valleys in my opinion. I just think it looks great. They even got the
Valley logo on the back of it there. The 70's were cool. So I hope you enjoyed the video. We'll
see you next time where we'll get into that MPU. I think I can get it. But if you want to see some
more about what became what was actually the Valley Star Trek game, check this video out.
We'll see you on the next one.