Check Out Our Patreon Account, for Unreleased Repair FAILS, Concise Repair Tips Not Possible In This Long Form Video, And 1 on 1 Repair Assistance with YOUR Project!
Thank you to everyone who has been supporting our channel! If you use the link below before you purchase anything on Amazon, we get a royalty for sending you there, thank you!
Our store is located at 139 Caldwell St., Rock Hill, SC 29730.
Ladies and gentlemen, this is Joe's
Classic Video Games back with another
cool pinball repair video for you this
evening. We have been working on this
Gotib Royal flush. And we did a long
video on it already where we kind of
limped through repairing it instead of
doing it the way that we usually do it
where we systematically go through and
clean all the switches, adjust
everything. We kind of troubles did
troubleshooting to figure out uh why the
game wouldn't start. And uh if you
missed that video, go back and check it
out. At the end of the video, I was
jokingly saying, "Oh, look. It's working
now. Everything's good." And then we
played it and it didn't advance the
ball. Um, which it was a joke anyway
because of of course we haven't serviced
a whole bunch of stuff on it. But I
figured I'd see if that's actually going
to happen over and over again. So, let's
see if it'll still
start. Might be short some
credits. Now, we've got some credits.
do the
500. Okay, let's kick the ball out. So,
what we did was we shot the ball up. Um,
it must have hit the runway switch
there, which probably only messes with
that. I think we scored that, got our
500
points, and then we lost the ball.
Notice that their first player is not
lit
up. Yes. Okay. So, I think we're in a
situation where it's actually not going
to advance the player unit. So, we'll
try some other stuff
here. Score that. Knock a couple drop
targets
down. Land in there. Yeah. So, we're in
we're in a place where there's still all
kinds of stuff not working. So, uh next
step, I think we will start going
through it systematically. Let me show
you how the player unit works, though.
how it goes from ball one to ball two
real quick so I can show you why it's
important to um basically hit everything
instead of trying
to peck and choose um which switch must
be screwed up if it's a machine that's
never been serviced. If it's been
serviced recently, yeah, if you get a
problem, just find that one switch
that's the problem. But if it's one like
this that's been sitting a long time,
all the switches are a problem. So,
these are the Gotlib Royal Flush
schematics. If you need some of these, a
good place to get them is the Pinball
Resource. Go to
pbresource.com. Uh, these are the
original ones that came with the
machine, but they make nice copies that
are nice and big like these that are uh
accurate and exact and they have the
license actually from GotLib to
reproduce those and all of that. So,
make sure to support them and check them
out. Also, they are the company that's
making all of the reproduction got parts
that we have available. Uh so, um it's a
great company. It's a mom and pop place.
So, the player unit is actually what
makes the ball count unit step up. Uh
because whenever it gets like if it's at
the first position, your player one ball
one, player two, ball one is the second
position and so on. So, to get to player
one, ball two, it has to move up to the
fifth position. And it didn't do that.
So, in the previous video, we worked on
this, but what we worked on was the
reset
sequence. So, we worked on when the AX
relay pops down, uh, it provides power
down here, through the start relay,
um, and it goes through the Z1 and Z2
relays and or, uh, gets to a certain
spot where it resets all of these, etc.,
etc. But whenever it whenever you're
playing the game, it has nothing to do
with it. When you're playing the game,
the way that the ad player unit gets
pulsed is through all of this. So power
comes through here, goes through the U
relay, which is the first ball relay
that pulls in whenever you score
something on your first ball. And then
as the score motor turns
uh and the P relay pulls in, which is
the uh add player unit relay, that's
pulled in whenever the ball goes through
the trough in the bottom. If the BX
relay isn't pulled in, which is the
um last ball relay, if it's not the last
ball in the game, and then as the score
motor's turning, blah blah blah blah. So
there there's all this other all this
has to happen to make the player unit
work while the game is being played. And
you have to have the switch on the Z1
relay and the switch on the Z2 relay
working right uh for it to work on the
way we did it was the reset relay I mean
the reset way so it didn't use this part
of the
schematic. So that's why it's working to
reset which you just saw but it's not
working during gameplay. So our problem
is probably on the U relay. It may be on
the Z1 or the Z2 relay. We're going to
have to clean all of that. So, I think
we'll start in the bottom. I'm going to
get a vacuum cleaner and start vacuuming
it out. And um when we get to the U
Relay, we'll check it out real close. My
theory is that switch there isn't
working properly. All right. So, I I
vacuumed it out, but it was actually
still in pretty good shape already.
There wasn't that much trash in there.
Of course, there's a lot of dirt and
discoloration, but you know, I vacuumed
out all of the dust bunnies at least.
Now, interestingly
enough, on the previous video, we worked
on the AX
relay, we worked on the game over relay,
we worked on the BX relay, and we found
that all of those had had switches
misadjusted and stuff, and wouldn't you
know it, the U relay is actually right
there. Didn't he mention something about
the first ball relay in the email that
he sent us? He said something about that
he had messed with the first ball relay,
I think.
Um all right. So we read this in the
first uh thing and he said what he said
about it was I would activate the AX
relay manually and it would stop the
game could be partially played at that
time. Often I would have to manually
trip the first ball relay and it would
work. So that's uh how he mentioned the
first ball relay. He says, "I watched
the videos and tried to clean and
realign the AX relay contacts. I failed
terribly. I did adjust the spring so if
the AX relay would click freely into
place." Okay. Yeah. Um, so I'm not,
again, I mentioned this in the first
video, I'll mention it here, too. I'm
not shaming anybody or anything like
that. When I got my first machine, I
couldn't fix a damn thing on it. I
actually sold it without fixing it. Um,
my second machine, it was already kind
of working. I didn't really fix much. I
got it working maybe a little bit better
and then sold it. My third machine, I
got everything but like one thing fixed,
blah, blah, blah. So, it's a learning
curve. There's nothing wrong with
tinkering with it. A lot of people, they
have the opinion, um, oh, uh, you know,
if you don't know what you're doing, you
shouldn't mess with it. I don't agree. I
don't agree at
all. That's the stay in your lane
argument. I don't like that argument.
Um, you
know, you bought the machine. If you
want to work on it, you work on it.
There's nothing wrong with that. And if
you screw up, you can get somebody to
fix it. Now, I guess it depends on what
it is. Don't try brain surgery if you
don't know what you're doing. But
working on a pinball machine, the damn
thing can be fixed. So, it's not that
big of a deal. So, if there's some stuff
misadjusted and all of that, that
doesn't really say anything about the
person that did it. It just shows that
they were trying to fix it. They wanted
to they wanted to play the freaking
game. I don't blame them. So, uh let's
look at that one next just for giggles.
But we're going to go ahead and clean
all of them, too. Um but that that would
actually be the next one that we clean.
So, let's see if it's adjusted properly.
All right. So, here is the relay.
If you look at that bottom one, I can
just tell by looking at it that one's
not going to touch. It's too far. It's
too far apart. So, it's been
bent. So, yeah. So, when the relay pulls
in, that one never closes. So, that
switch exists for a reason. It needs to
open and close. Right now, it's just
opening. It never closes. The rest of
them, though, look as if they're
probably close enough that they work.
So, I'm going to clean them and adjust
that one. Let's see what that one goes
to.
Um, red and white wire, which I know is
the the main power feed, I believe, and
white and blue
wire. So, one tough thing about the
schematics is it's hard to find which
switch is what because there's no list
um in the schematics of each switch.
Sometimes in the manual though, it will
show you that. Um, some games have
manuals, some don't, but sometimes there
is a list of the relays in the manual
and it'll show you every switch that's
on it and what the color of the wires
going to that switch is and what they
do. But sure enough, white and black or
white and blue, BL means blue, B means
black, white and
blue, a switch on the U relay, and then
the other side is Are you ready for it?
I think you're ready for it.
Oh, it's red and
white. So, we got it. I knew exactly
which switch it was. Look at that.
That's impressive, isn't it? I go ahead
and pat myself. Oh, I fell down patting
myself on the back. Okay, so I cleaned
through all of the switches and the
switches on the score motor. Let's see
if it fixed that one issue or if I've
made it any worse and then we'll
continue. Well, let me get some more
credits on it again.
It's definitely not on free play
[Music]
yet. All right. So, our whole thing is
we're just trying to get it to
um advance to the next
ball. That's exactly what we did before.
Okay, so it advanced two
positions, but it didn't get to position
four. So, it advanced past one and pass
two, but stopped on three. So, that's
our next little clue. Let's see if
whenever this ball
ends, what it does next.
Okay. So, that time it made it. All
right. That's an interesting little
problem. Let me show you what that
problem is. So, we're back at that same
exact place and that switch was the one
that was open. We have fixed that. So,
now power connects through here. And
then it gets up to
here.
Um, coin unit.
We'll look for the coin unit. But as the
score motor is turning, when the ball
goes through the trough, it closes the P
relay. Now, that U relay is permanently
closed. That will just stay closed. So,
all of these are
permanently, you know, power can go
through them. I don't know if I should
say permanently, but
um so uh this P when it closes as the
ball goes through the thing, that's when
it starts stepping
up. So why would it only step up two and
then stop? Well, there's two reasons. It
could be that P isn't holding in long
enough and it drops back out, but that's
probably not it. So you have the BX
relay here, which is uh the extra ball
relay. So, if that hasn't pulled in and
I've cleaned that, that should stay how
it is, right? And then the power should
come up to
here. And then as the motor turns, the
score motor when it gets to position 1A,
it will close or whatever it does at 1
A. Looks like it closes five times.
Actually,
bup. And at the same time back here, you
have motor 2C.
It's going to close
uh at a certain
place. That's
interesting. Okay. And then power comes
through here. It goes through Z1, which
is closed. And then power goes through
Z2, which is
closed, and it gets up to here, and it
adds the player unit. So, we just saw it
do that twice. It added the player unit
twice. Okay. So, this is the interesting
part. Motor 1A. Now, this is kind of
deep schematic theory, but you're going
to love it. If you get your mind around
it, you're going to say, "What a
genius. What a genius way to do it." So,
when the ball kicks over that P
relay, the P relay pulls
in and a switch on
it, turns on the score motor. The score
motor starts turning.
And there is a switch in line that we
just saw at position
1A.
Okay, here is the chart of what the
score motor
does. So when the uh A is the bottom cam
on the score motor and it has five
little bumps on
it, right? And this will turn from home
position to home position which is 120°.
The score motor is
360°
round, but from home position to home
position is 120°. And so as it, you
know, the motor just started turning
because the P relay come in. And so when
it gets to this area, which is right
before it gets to 30°, bam, it closes
that switch. And then when it gets to
this area, which is a little bit, you
know, right at 45, bam, it closes the
switch again. And when it gets to this
area, which is at 70, bam, it closes the
switch again. And then when it gets to
this area, which is just before 90, bam,
it closes the switch again. And then
when it gets to this area that starts at
105, bam, it closes the switch again.
And then it gets back to 120, which is
essentially zero. And it'll
stop. So it closed the switch five
times. Bam, bam, bam, bam, bam. Right?
So that is it moved. It could have moved
the player unit five times. Bam, bam,
bam, bam, bam. which would be kind of
weird because you'd end up on ball to
um player two. So, the Let me show you
the player unit. We went all over this
last time. We haven't even cleaned all
of this yet, but the player unit, these
little things are on these certain lines
here. And you can
see that right now it's on this line,
we'll call it. It was over here. This is
player one, ball one.
What it did was it advanced two to right
here. This is player three ball one.
This is player four ball one. This is
player one ball two. So it advanced up
to player three and
stopped. So it gave us two
advances when it should have gave us
four advances. The next time we did it,
it gave us two more advances. Okay. So
why is
that? That's a great question.
When the score motor starts turning,
that hits five times. But if you look
back here, it's disconnected because of
all of
this. So, one of
those is motor 2C. So, that's on the
score motor, which will start turning.
Motor
2C. So, here's the part you're going to
love. So, motor 2C is a switch right
there.
that connects at that point. Now that's
the only place it connects
at and if you look that overlaps that
point. So at that exact spot of the
revolution both this switch will be
turned I mean uh will be closed and that
switch will be closed. So what's going
to happen? Score mode will start turning
and when it gets to here this switch
will close but nothing will happen
because the line is broken. When it gets
to here, this switch will close and it
will advance one position because this
switch is also
closed. Motor
2C and then it will advance to the next
place and 2C will be open by then. So
nothing will happen. The next place
nothing will happen and the next place
nothing will happen. So this switch is
closing five times but only at one of
those spots is another switch closed to
make it advance one place. So where did
all the
other advances come
from? They come from these other
switches.
P2G,
P3G, and P4G. So what are those? Those
are switches on the player
unit. So P2G, P3G, and
P4G are on these
stacks. So we'll say this is one, this
is two. So, switch G, which may actually
be that top one there that we're looking
at. I don't know, maybe the one below
it, player 3G, player 4G, P or player
unit 2G, 3G, 4G. So, if those are
closed, it does it again.
So, score motor starts turning and it
pushes it up. When it gets to here, this
switch is closed. So it pushes it up and
it just pushed it up to player two.
Right. Right there. Ball one, player
two. And so now it gets to here. Well,
when it gets to ball one, player two,
guess
what? That closed P2G. So now that one's
closed. So it's still turning. And it
hits here. Bam.
And if that switch is closed, it's not
on here because it's a different setup,
but if that switch is closed at that
position, uh when it gets to here, it
will hit again and make that forward one
more spot. So, it skips over to player
two. And that now it's on player three.
All right. So, when it got to player
three, P3G should have been closed.
So, since it's closed, this switch hits
again. Bam. And it moves it from player
three to player four. And then it gets
to player
four and P4G is closed. So, when it got
to player
four, it hits again. Bam. And advances
you to ball to player one, the next
position. Well, I cleaned all the
switches and I cleaned the score motor,
but I didn't mess with the coin unit. So
the this is the coin unit in this
game. Got only did this setup really for
a little while. They had other ways of
doing it. They had a a relay bank that
they used it on on like that Jack in the
Box that we did the other day. So this
resets the unit and that adds the unit.
So when if you put more than one player,
this moves. Okay. So I'll move and I'll
show you how it
says one can play at the same time. Two,
three, four. Well, if I move this coin
unit
up, two can play at the same time. That
means it's a two-player game. Now, now
it's a three-player game. Now, it's a
four-player game. That one bulb, let me
see. That one bulb is a bad connection
on the on the uh coin unit
here. Right. So, what is the
significance of that? Well, that's the
missing that's the missing piece of the
puzzle here.
This is the coin unit. Now, this is all
drawn kind of backwards. It's all
backwards from how you might
think. If the coin unit has not been
advanced and you're on a oneplayer game,
it is set up like this. They are showing
you a one-player game. Ball one, player
one. The ball's sitting in the out lane
and they have unplugged the power. Okay,
so these three are connected. But what
happens if you start a two-player game?
What happens is the coin unit advances
to here. So this top
piece, it spins around. You saw that
it's a a stepper unit. This top one
becomes disconnected. And now that one's
connected and that one's connected. So
with the top one
disconnected, power comes through here.
And when the player unit when the ball
goes through the trough and it makes the
P relay pull in which starts the score
motor and this starts hitting 1 2 3 4 5
like we talked about. When it gets to
position
2C, it closes that one which advances it
to player
two, ball one. Okay? And then the switch
at P2G closes because you're now on
player two on the player unit. But this
is open. So nothing
happens. So it just stops at player two.
Okay. Well, at the end of player two's
game or
ball, uh the ball uh goes through the
trough again, turns on the P relay. The
P relay starts the score motor. It
starts going bam bam. And when it gets
to motor uh
2C, it steps up one position again. So
now it goes from player two to player
three. Well, now that it's on player
three, this switch closes.
And the coin unit, that part is still
closed. So it steps it up one more
position whenever this hits its its uh
third spot, right? Uh or its fourth
spot, whatever it is. And so now you're
on player four. And so this switch
closes. And then the score motor is
still turning and this is still
connected. And so it steps it up again
and it gets it to player one and then it
stops at player one because it always
stops player one because there's always
a player one the way it's designed. All
right. And similarly you can understand
that if you started a three-player
game, this coin unit would move up here
and both of those would be open. So when
it got to uh player two at the end of
player one's ball, it would stop. And
then when it at the end of player two's
ball, when it got to player three, it
would stop. And then at the end of
player three's ball
one, it would come
through U and whenever that hits, it
would move it on right to player one
again. So the same thing. So because of
the coin unit still being dirty, what's
probably going on is this switch. It's
either this switch or the coin unit. I
can't remember if we cleaned all these
last time, but basically we need to
clean the player unit switches and we
need to clean this coin unit. The coin
unit is really simple in these. I'll
show you that a little closer. So, it's
just a little stepper unit. It's got one
coil down there that advances it and
then one coil that resets it. This is
Gotlib standard stepper. I mean, it they
use this on all kinds of stuff. They use
it for like the bonus sometimes and just
different things. Um, and there is a
switch there.
What in the hell is going on with
that? Well, that don't look
right. What have they done to our
switch? I can't even tell what's wrong
with it. It's so screwed up.
[Applause]
Um, let me try to reset it here. So,
we're on position four, I believe.
Right. So, if I hit
that, that has moved it
back. Look at this. See, that's not
right. That's not how it's supposed to
be. Okay. So, it's in that position.
Then, if we step it up to position
two, it's
open. Position three, position four. So,
that that's not right. Okay. So, let's
see what this switch is. That's probably
the one that should open at position
four. Okay. So, it's that switch right
there. See, it says third position coin
unit. And so, that is used to make it
where the V relay will not pull
in. And it says third position, which is
actually the fourth position because
there's a zero position. So, it's 0 1 2
3. So, why would they put a switch there
that opens at the third position? and
turns off the V relay.
Well, the V
relay is the replay button relay. So,
when you press the start button, it
pulls in that relay and adds another
player
basically. So, why do they want it
opening at the third position? Because
they want you to be able to start a
one-player game and then a two-player
game and then a three-player game and a
four-player game. But when you get to
the fourth player game, they don't want
that start button to do anything.
because if you hit start again, it's
going to take another quarter from you
and you can't start a fifth a five
player game. Um, so they've got that
designed in like that. So why uh why is
it opening the way it is? Well,
somebody's really misadjusted it or
taking that off and put it on backwards
or something. I'm going to see if I can
um find a Let me
think. I think they've just got the on
the wrong side of that post. If we if we
move it around to the other side of the
post, we'll see if it works properly.
Actually, there's plenty of room. I just
had it bent weird. So, this is position
one or position zero, actually. Position
zero. And it's closed. Okay. So, you hit
start, two
player, three
player. Is it still closed?
Yep. Four player. So at the fourth
player it opens and then when it
resets. Okay. Yeah. So this coin unit is
not resetting all the way back. Watch
how I can just do it with my hand. It
should be resetting all the way back.
All right. So this all just needs
rebuilt. But that open that should open
whenever you get to the fourth player so
that you can't steal another credit. But
it's a very simple thing. You've got
that one switch. You've got the two
coils. And then you have this
um
uh I can't even think to what to call
that platter or whatever cam mounted on
it. That just needs to be clean and
where all of the rivets and everything
are clean. So I'm going to take that
off. You've kind of got to usually take
the screws out of the mount so that you
can move that so you can get to that
side of it. But let me get that off and
I'll show you what it looks like
underneath it. All right. So, I have
removed the wafer, the disc, the cam,
and you can see what the problem is.
It's just everything's so
grimy.
Look. See, you just need to clean all
that up. So, I'm going to take sandpaper
and lightly clean that. You can do it
the way you want, but that's what I use
is sandpaper. And then after you do
that, you need a little bit of grease to
make it where there's no friction as the
thing spins over those
uh rivets. If you look, you'll see the
traces of grease that were on there
before. That's because they used that
from the
factory. So, you need just a little bit
just to lubricate it because if you
don't, you're just going to have metal
on metal. Not a good idea. So, this is
what we
use. We use super lube. It's dialectric.
Wh I always go a little bit too far.
Dialectric. Look, it's food grade, so
you can drink this stuff. Um, so, uh,
put something like that on there. You
can get that at the hardware store. If
you don't want to get it at your
hardware store, uh, you can support our
channel by going to our website. Go to
lionsarcade.com. We've got stuff like
this on a parts page listed on our
website. And it's stuff that's listed on
Amazon, things like that. It's
got made in the USA, so it's tariffree.
No terrifying tariffs for you. Um, so we
appreciate everybody that's been doing
that. If you go buy any of that stuff on
Amazon or just click the link and buy
something else on Amazon, it gives us
credit for sending you there and we make
money off of that. So, we appreciate
that. Um, so I think I will clean this
up like usual. Put a little bit of that
on there and then we'll see if this
thing works the way it did. Now, you
might be saying, "Well, aren't you going
to completely disassemble it and clean
the bushing and all that?" Usually, it
doesn't need it. If it needs it, I will.
But usually it doesn't. Usually, uh, it
the problem is right here. It's just the
resistance on these rivets because of
all the grime and the grease. That's all
covered up pretty good, you know, and
it's a nylon bushing on metal. It
doesn't need any lubrication. And this
is another good test for things like
this. Look how well that moves. So,
there's a spring on the other side. See
how well that's springing back where it
goes? And remember, it only moves four
positions. The bushing isn't the
problem. The the
the resistance on the rivets is the
problem. All right. So, uh, let me, uh,
clean that up and then we'll see if I'm
correct about that being the only issue.
All right. So, we can see it better now.
position one and it reset on its
own or position zero actually. Zero,
one,
two. No, I had it
wrong. Position
zero. One,
two, three. No, I've got that all wrong.
There's only three positions. So, this
is a oneplayer
game. Two-player game. three-player
game. Four player game. Okay, I guess
actually I am right. So, it's zero. It's
one. Let's Let's start at one. One, two,
three, four. Yeah, I'm correct.
Okay, so position zero, one, two, and
then three. And it's open at three, so
you can't do it again, which you
couldn't anyway, but they don't want you
to waste your quarter.
And we've got the switch adjusted where
it's through the switch. All right. Now,
I know what you're thinking. Why is that
bent? Well, sometimes if it's hitting a
cam, it's a little easier to have that
bent than have it bent way back
here. Do as I say, not as I
do. You do it however you want. That's
just how I chose to do it on that
particular one. Now, on the other ones,
they should be straight, but you get you
it'll be all right. Don't worry about
it, folks. Uh, yeah. So, it's resetting
good. Everything's cool. That's all
sweet. So, we'll put that back together.
We've got all them. We've got them.
Let's see if that alone fixed the uh
ball and play thing that we were having
or if we need to mess with the player
unit next. Now, we're still we're going
to mess with the player unit, but let's
see just for giggles. Was it just this
or was it the switch on the play on the
player unit? All right, folks. We're
going to try it again.
Let's see if it advances properly. It's
a oneplayer
[Music]
game. Oh, it did not. Okay. So, our
problem is not the coin
unit. Our problem must be the switch on
the player unit. Let me go back and look
at the other video and see if I actually
cleaned all those switches or did I just
clean one switch because that's what the
video was about. Let me see what I said
that I did here. I was just pointing out
that little switch. All right. So, I
adjusted it a little bit, cleaned it,
and put it back. Now, I didn't clean
anything else. And keep in mind, this
wasn't moving. I didn't clean anything
else. Now, I just did that because I was
trying to make a point. Always clean
every switch. We're systematically going
through it now, but I'm just showing you
how we're tracking down the issues as we
clean. Uh, just trying to make the video
more entertaining. It might be making it
more boring. You let me know down below.
So, yeah. So, we need to clean all of
the switches on the player unit, and I
will check those three switches to see
if they're gapped properly or if it's
just that they're dirty. And, uh, I'll
show you whatever I find out. All right.
So, I cleaned it up.
Same thing with the rivets as well.
Um, yeah. Okay. So, I was looking at the
schematics to see if the rivets could
have had anything to do with it. It's
not. It's the switches. The switches
looked fine. Um, uh, they were just
dirty. So, none of them were seemed
misadjusted at
least. All right. So, let's see u if it
if that has fixed it or what's going on.
We haven't done the score rails yet. So,
you see how the one's a little
crappy. I got
it. All right. So, what do you think,
folks? Is that going to get
it? Well, I have to score some
points
or it didn't score anything. That's
great. It did score that. All right. So,
let's There we go. All
right. Cool. So, we at least figured
that out. Let's try it one more
[Music]
ball. All right. Cool. So the whole
problem was now you see how it's moved
from player one ball one player two
player three player four player two ball
one player two player three I mean
player one ball two player two player
three player four and now it has landed
on player one ball
three that's why we have lit up what we
have lit up so cool all right so
obviously the 10 points isn't scoring
let's try since I did the the things on
on the
bottom. Earlier, we noticed that when
the ball lands in there, nothing
happens. Now, it kicks it out. Why would
that be? Well, I I cleaned the hole
relay, I think it was called. Something
like
that. So, that must have fixed that part
of it. Let's see if we can turn one of
those
on. How did we Oh, I think you hit this.
Well, maybe they hit that. Whatever.
Let's see if that does anything. So,
we're at 2500
points. Nothing. So, it's still not
quite right, but um we're getting there.
So, we're slowly going through and
cleaning things. So, why would that be
not scoring right? Well, there's
probably something on the bottom of the
playfield. We haven't done any of that
yet. Or maybe it's the
uh maybe it's some of these
uh score relays. you kind of you have to
go through and clean every single switch
if it's been sitting a while. Another
thing that it could be is all these
Jones plugs. So, that's coming up as
well. What I may do is that little thing
that we just did earlier where it
wouldn't advance the player unit, and we
figured out that it was the switch on
the U relay. And by just doing that, it
fixed it to where it at least advanced
two positions. Um, and then uh after
that we figured out, hey, why isn't it
doing that? We figured out it was the
switches on that. And after doing that,
it advanced it all the way through. I
may cut off just that little piece
that's like two or three minutes long,
maybe where we found the URL and upload
that to our new Patreon channel. So, we
have a channel. You can find the link
down below all of our videos in the
description uh on Patreon. Now, nothing
on YouTube is going to change. You just
watch this full video. We're going to
keep doing the videos the way we've
always done them and just as often as
we've always done them. Uh
but we I've thought for years about the
Patreon thing. You if you don't know,
you have to pay to subscribe to
somebody's Patreon channel, which is
awful awful tempting as a content
creator, but I didn't want to set up a
Patreon where it had exclusive stuff
that uh you had to have money to watch.
I don't really like that. I like the
idea that all these videos are free,
which they are here on YouTube. Um, and
then of course, I'm sure you realize we
make money off ad revenue and things
like that. So, I've thought a lot about,
well, what can we do on Patreon that's
not a slap in the face to people that
can't afford it, um, but that's an extra
value that people might enjoy. Okay. And
so, we've came up with a couple ideas
about we've got uh three or four things
that we're going to upload on there. One
thing we're going to upload on there is
more concise repair tips that are edits
of the videos that we've already done.
So, like I was just mentioning, if I
took out just that one little piece of
this video and uploaded it on Patreon as
its own thing,
um, that's pretty cool, you know, and
you can put the title, uh, if your
player unit isn't
advancing properly, check this out or
blah blah blah, you know. So, uh, and
that's maybe that's not even a great
example, but there's plenty of them that
I can do that with. We've
got,300
videos and hidden inside of all of those
videos are little repair tips where we
figured something cool out like that
right in the middle of the video. Um,
and as you can tell, I'm quite
loquacious. I like speaking a lot and we
we cover a lot in our videos, but stuff
gets lost. It's just, you know, people
email me and say, "Hey, uh, uh, you
know, somebody emailed the other day and
said something about how the the kicker
wasn't kicking the ball all the way out,
and they wanted to know, they remembered
that I showed that in a video, but they
couldn't remember which video it was."
And then I started thinking about it and
I thought, I think it was in that
abracadabra video. I don't remember. So,
there was this cool little part in one
of those Abracadabra videos, uh, where
the ball wasn't kicking all the way out
and we figured out what the issue was.
So, now I got to go look through three
or four of those and try to find exactly
which one it was, right? So, there's a
real problem with indexing on YouTube
just because there's so much content.
So, I I think on Patreon that could be
one thing that we offer, but it's not
really keeping anything from somebody
because it's still all of it's readily
available on our channel. Let's just you
got to find it. So, there's that.
There's also there's clips that we
haven't been able to upload in the
videos because it's repair fails. Maybe
we just started working on something,
never fixed it. We've got three or four
minutes that we filmed on it and we just
never released it cuz, you know, it's
not showing anybody anything. So, it's
it's almost like outtakes and bloopers.
So, we put a little bit of that stuff up
on there. Um, we've also got sometimes
we'll be playing a jukebox or on our
amateur repair time channel, we'll be
playing a record player that we just
repaired. And YouTube hates it. They
will not let us play music. If you don't
know, if you if you play about six
seconds of any kind of music that you've
ever heard, it can it can identify about
everything. If you play about six
seconds of it, it takes the revenue that
your entire video makes. So, like if you
have like an hourong video, you play six
seconds of uh Korea's Clearwater Revival
song for instance, moni non monetize.
You didn't create that. No, that's that
belongs to Universal Music Group. We're
going to give them all of the proceeds
of your video, your hourlong video that
you made. That's YouTube stance on it.
Patreon, you can upload whatever you
want because they're not playing ads on
it. So, they don't have the same
problem. So, we can upload little clips
where we played music. YouTube wouldn't
allow it to be uploaded, put stuff like
that on Patreon. So, if any of that
sounds interesting to you, the link is
down below the video. Check it out and
you can go over there and there's some
stuff up there you can just watch. You
don't even have to be a member or
anything. So, um we may do that. But, um
yeah. All right. So, that's we've
basically worked through the bottom of
the of it. We got it fixed in the first
video. We got it to start up. We've
worked through the bottom mech board.
We've worked through the player unit.
That leaves us the relays in the back
box, the score reels, which are always
fun. Oh, I can't wait. Oh, can't wait to
do the score
reels. They're not that bad. And uh the
stuff hanging under the playfield and
then we have to troubleshoot it. So,
we've probably got one more video, maybe
two more videos on this one, and then
it'll be done. The playfield itself, the
customer uh wanted to do that, so he's
already messed with that and he's he
feels confident with that. So, he
doesn't want us to clean it up or uh
replace rubber rings or anything like
that. He's going to handle that. So,
we've just got to get it where it
reliably works and everything's good and
solid. I feel like the mech board is
good and solid because we just work
through the whole thing. There's no more
problems down there unless we find
something while we're troubleshooting
it. Uh, but we need the same kind of uh
reliability out of the rest of these
relays in the back
box, out of all of these score
reels. We got to clean all the Jones
plugs and not just the ones that connect
things. Stuff like this where you the
three or four five ball adjustment,
that's a Jones plug. That needs to be
cleaned, too. If that's not making good
contact, you're going to have problems.
So, we still got to clean all that
stuff. and uh the stuff on the bottom of
the playfield we need to mess with. Tons
of relays and things under there. Um and
we need to play it. So, there's still
plenty left to do. Hope you've enjoyed
it so far. Leave your comments down
below and we will see you back here in a
couple days where we'll go through it
again. Now, if you like these uh mid70s,
late7s got games, so do I. I'll put one
up here for you to watch one that we
repaired a while back.