DR #5 - Bowers & Wilkins CCM663 Speaker Troubleshooting and Repair

Duality Repair
132 followers
486 Video Views·Mar 12, 2025
In this video, I document the repair of a Bowers and Wilkins CCM663 ceiling mount speaker. The initial complaint was that the sound was muted or restrained. After the repair, this thing sounds sweet!!
hey everyone this is Nick welcome back
to another duality repair video tonight
I'm gonna be looking at this B&W CCM 663
speaker it's a ceiling mount speaker and
it's pretty cool-looking so I'll show
you wrong just for a second it's pretty
neat looking like that blue very nicely
looks like Kevlar blue so this is a
ceiling mount speaker mounting to this
bracket here so you mount this bracket
into the ceiling you have your input
connections right here
what they do they use this 4 pin
connector which leads to a 4 pin
connector on this side connector here on
the speaker which leads to this board
goes through right here this goes to an
equalizer switch you can set your
equalizer in positions and then dose
across this board and then finally ends
up here on this panel where part of it
goes to the tweeter and then the other
part goes to the voice coil so pretty
nice little compact speaker really solid
this thing is probably 10 or 15 pounds
so story with this is I got it from a
customer yesterday dropped it off he
told me that the he bought it from the
original owner for very cheap because
the original owner said it didn't work
right out of the box so I've never
worked on a speaker before but I think
I've already figured out what's wrong
with this so take a look at the board
here and right there so this was not as
apparent as it is right now it was it
was pretty well flat you know they were
pretty well made it together but I saw a
crack so I kind of pulled on it and so I
pulled it down just to verify and it's
very badly crack as you can see it's
also another crack over here it's very
difficult to see on camera I'm gonna
take the board out and you'll be able to
see it then but there's a crack over
here try them happen is original owner
either dropped it or set it down
you know during installation and set it
on this end well you got to do is set it
down like this you can't really see it
but if I set it down like there you got
10 to 20 pounds of force just setting it
down if you were to drop it at all
this is absolutely gonna break this is
pretty flimsy PCB material so that's
what I think happened we're definitely
gonna have some inconsistent or missing
traces here and inconsistent connections
so that's definitely gonna be I'm gonna
guess our only problem I took a good
look around everything wants to be solid
on the speaker and you can't see all the
details the voice coil isn't shorted out
or anything everything looks to be in
good working condition physically I
don't see anything else wrong with this
so next I'm going to remove this board
so we can take a closer look the board
is out of the unit so let's take a
closer look so again this first crack is
very apparent we flip it around I get
you in the right light here there you
can see the traces you can see how even
the traces are bending so we're gonna
have an intermittent connection okay and
so again this is our input here on the
left our equalizer channels here and so
the major break is on the equalizer
channels but our signal is you know it's
definitely gonna be compromised with
this broken board here so let me show
you the other crack right there well you
can get a pretty good glimpse of it so
can't see from the top very well
so it looks like you can see it it's
that crack is creeping up to that trace
right there so I want to guess that that
trace is compromised as well so really
what I'm going to need to do is drop
just a very simple schematic obviously
it's gonna be simple there's not much to
this but just draw it up the best I can
trace it out with the multimeter draw up
a schematic so that I can basically I'm
gonna I'm gonna bypass this whole
connection right here I'm gonna have to
desolder all of these pins and make
direct connections to to their final
locations wherever they happen to be and
then I'll probably have to do the same
with that trace so that's gonna be one
of these equalizer pins as well I
believe to wherever that's going mmm the
output of this filter here it's a coil
here so so next I will drop a quick
schematic at least of this front end
here anything that shows a compromised
trace so that I can use that as a guide
for when I kind of rewire this thing so
I'll drop a schematic all right so after
examining the board a little more
closely I realize I don't need to worry
about these input pins right down here
none of these have any compromised
traces whatsoever the other thing I did
notice as well some of you might have
understood before I did but these little
lines in here I was under the assumption
that these were the traces but these are
actually the separations between these
traces so the traces are these very wide
areas here these are all the traces that
makes a lot more sense since the traces
don't actually go through any of the
connections
it's these wide-open areas that are
actually the actual traces so a few
minutes to figure that one out but
anyway so I drove this quick diagram
here very very easy if it'll focus there
we go so on the Left I have the four
equalizer pins labeled s B AC s b AC and
then I call it you know I put there
color as well so white black yellow red
and then I put the Pater pins that they
that they traced to and luckily each of
them only traces of one pin so the S pin
or the white wire goes to wf+
so that's white wire here if you follow
the trace it goes along the top of the
board all the way across the board down
to this pin on the left here if you flip
it over wf+ so that's the woofer plus
side of the woofer okay black focus
black goes to l3 so I call it L the
inductor they have an L label down there
as well you can't see it and then three
for the pin so if you follow black
that's this pin here follow that trace
up and around actually it only goes to
right there very easy so I flipped that
around in three of the inductor and then
the same with the other two so a which
is the yellow wire leads to pin four of
this same inductor so pin four is over
here and then the red wire or C leads to
pin two of the inductor so the red wire
C let's leads to pin two right there
okay so all I'm gonna do I mean this
board is already broken so I'm gonna
have to remove this chunk of the board
and I'll probably desolder all four of
these and I will just bridge these with
new wire to their associated pins so one
here one here and then here in here I'll
bridge those and I'll come back when
it's all done we'll take a look at it
and I'll use the meter to make sure that
my traces are solid and that you know I
have good connection between each pins
and then we'll reinstall it into the
speaker and we'll test it out make sure
this thing works
be right back all right before I remount
the board I'll show you really quick
what I did so first thing I did was
desolder the connections here and I had
kind of cut this part of the board out
to clean it up that's about as clean as
I can get it and so now I've joined each
of the four wires from the equalizer to
four new wires and then applied some
heat-shrink all I did was I twisted them
together together soldered them together
and then added the heat shrink so that
these are they're pretty well connected
right now I feel pretty confident with
those and then of course I soldered each
of the wires to their respective pins
what I talked about in the previous
segment so these four pins here so I
feel pretty confident about these
connections the lengths are good as far
as they're gonna everything's gonna
reach and I'll be able to install it the
last thing I really have to do before I
before I'm ready to kind of set this
thing up permanently is to clean the the
wires up a little bit it's a little wire
management so I'll get probably two zip
ties those I've tie these together here
at this point clean that up and then
I'll clean this up a little bit to kind
of zip tie these together and then I may
need to do a final zip tie once I have
the board installed here just to maybe
zip tie these to the post or something
so that they're out of the way they're
not gonna interfere with the speaker and
they're also not gonna interfere with
the mounting rack that I showed you
earlier so I'm gonna get this installed
just so I can test it I want to see how
it sounds see if it works or perhaps it
doesn't you know we might have other
issues I may have screwed something up
never know so I'm gonna install it and
we'll hook an amplifier up to it and see
I'll see how it sounds all right I'm
honored the board inside the speaker and
then I mounted the speaker inside the
housing assembly and then hooked up my
speaker wire here from any amplifier and
then I have some royalty-free music hook
up to my amplifier via my computer
so I got quite the system going on here
it's the first time I'm gonna give it a
shot so let's let's see if it makes any
noise at all
here we go can hear something
turn it up sounds good
[Music]
three clean three nothing more that
speakers fixed
[Music]
[Applause]
[Music]
to win right there
I miss all right Cheers
[Music]
[Applause]
so I'm sure the owner would be very
happy to know that this speaker is
working perfectly as I said all I need
to do is clean up the board a little bit
make sure the flux is cleaned up on the
little cable management make sure those
cables are nice and tight by the way the
speaker out of the way the housing
assembly and this thing is done very
exciting I love it and that's it for
this one I will see you on the next
video it won't be too long
have a good one thanks for watching
[Music]
not bad for really free too
[Applause]
you
