DR #24 - Rotel RSX-1067 Receiver Troubleshooting & Repair - No Volume Control & AC on the Output

Duality Repair
132 followers
11 Video Views·Mar 12, 2025
In this video, I document the troubleshooting and repair of a Rotel RSX-1067 surround sound receiver with no volume control and AC voltage on the output. Using schematics, a multi-meter, and some logic, I'm able to identify the faulty components.
hi and welcome to do ally to repair I
have another Rotel unit this is the RSX
1067 surround sound receiver and it's in
good shape cosmetically but it's got
several problems that we'll have to deal
with but before we started to
troubleshooting and repair I did want to
bring up that I just recently started a
patreon account and I did this because I
want to be able to work on more
equipment like this I love working on
these amps these receivers but of course
I'm buying this with my own money and so
I'm buying it and then fixing it and
selling it and hopefully but I'd love to
be able to work on it more often as well
as higher-end units and the only way I'm
gonna be able to do that is with some
sort of outside funding so if you're one
of those people that wants to see more
content from me or wants to see me
working on higher-end equipment whether
it's amplifiers receivers oscilloscopes
power supplies please consider joining
me on patreon the link will be in the
About tab one good benefit about joining
me on patreon is that if I were able to
receive enough support I'd be able to
give some or most or even all of this
equipment away I have no use personally
for this equipment for most of it I keep
a few oscilloscopes and power supplies
that I work on but a majority especially
for this audio equipment I have no use
for it I have my own setup I don't need
it I simply like working on it and so if
you're interested in seeing more content
for me be working on higher and
equipment or just interested in possibly
receiving free equipment please consider
joining me on patreon all right that's
enough of that so let's get into the
failures so you can see we do have
standby light that's great let's turn it
on and the initial problem shows up
immediately right here so the volume
doesn't change at all okay we got a
little bit there but it should be
changing rapidly right here the other
problem I haven't tested because of this
volume issue as advertised is that one
of the outputs is out and so there's
obviously several surround outputs I
believe they said one of the center
outputs is out we'll have to test that
but we have to fix this issue first and
so normally I don't jump into the
schematics right away but I did on this
unit and so if we look at the schematic
we can see that the volume knob as well
as the bass and treble control knobs all
lead are all controlled by this one
micro control
ic1 and so if we go back to the unit we
can see that they label this LF for low
frequency that's the base control the
base control works just fine we can go
from min to max no problem same with the
high frequency or the treble control no
problem there so that tells me that that
I see one is probably functional and so
there's probably something wrong with
the circuitry leading to the volume knob
or the volume knob itself and so one
thing I did find out just before I
started this video is that yes I cannot
adjust the volume by just turning at
standard but I had some flashbacks from
my Harman Kardon where the volume knob
was definitely smashed in and it broke
part of the the input board there or the
the front front board and so I thought
something like that may have happened
here this is protruding further than
anything even further than these
elephant hf knobs and so I thought maybe
somebody pushed on a little too hard and
so what I tried was I pushed in a bit
and tried turning and if I get the
pressure just right you can see it
turning yeah it turns a lot easier and
so you can see I can adjust that volume
yeah halfway decently if I apply a
little pressure and so that tells me
it's probably some sort of physical or
mechanical issue with this volume knob
or how it's attached to the board I
don't really like that I really hope
it's not like the Harman Kardon back in
the day where the board was was cracked
in several different places that thing
was just toast I really hope it's some
sort of weak solder connection or
something like that but the only way to
figure it out obviously is to get inside
so let's do that
I removed the front faceplate here and
it's very very straightforward we have
four screws on the top here we have
several screws on either side you can
see the screw holes here it's the same
on the other side we also have several
on the bottom all those had to be
removed I would only have one tip
somebody's trying to do this this front
left screw right here is not accessible
due to the heat sink on this board here
so what I did was I removed three or
four
Kruse I was able to slide the board over
enough so that I can get my screwdriver
in there and remove the screw now I
still won't have access to the board I
need so I need to disassemble this even
further all right we're in pretty deep
now as you can see I have the board
removed from that front panel and
there's only a little bit further that I
can go removing this board from this
mounting block here
unfortunately my cable to do that right
now this I believe this is the bass
control knob is I believe it's glued on
to the shaft of the rotary encoder I
cannot get it off this one comes off
pretty easily but this knob does not
come off
I think I'll break it if I try to force
it so I'm gonna leave it on for now I
don't think I need to take this off for
now I looked around the board so
obviously here's our volume encoder and
that's these three pins here and I
believe these two pins are for mounting
to the board as well but these three
pins are the actual contact pins and I
looked around quite a bit I don't see
any signs of the board being cracked
I think the solder joints look good the
I see one over here looks okay you can
see a lot of flux residue over there but
that's fine I'll probably clean that up
before I get this reinstalled so I'm
thinking that it's actually this rotary
encoder that's gone bad so we can test
it before pulling it out of the unit I'm
gonna need to solder some wires to these
three pins here because I cannot get my
leads on there I want to be able to clip
them on there and have a free hand to
rotate this so I'm gonna solder some
leads on here and we'll test it I'm
ready to test the functionality of the
volume encoder you can see I have both
the volume coder knob as well as the
treble controller knob marked so that'll
be really easy for us to tell how far
we've rotated it when we're testing I'm
going to use the treble control encoder
as a reference because it's functioning
really well and you'll see that in just
a minute
very quickly on the theory of these
types of encoders they're very very
similar first of all they're both 24
pulses which means that as you rotate
each of these encoders
one full revolution you'll short out pin
one to pin 3 24 times you'll also short
out pin 2 to pin 3 24 times the only
difference is that these 2 pins are
going to short out out of phase due to
the way that they're located inside the
encoders themselves and that's how the
IC knows what direction you're rotating
the knob it's looking for which pin
shorts out relative to the other
and so if pin 1 shorts out to pin 3
before pin 2 does it knows you're
rotating at a certain direction and it
turns the volume or treble or bass up or
down accordingly and so the setup I have
is I have my negative lead of my
multimeter hooked up to the ground pin
or the common pin and it's all the same
between all three encoders which is pin
3 and I'm going to start by having the
positive lead of my multimeter hooked up
to pin 1 of the treble controller again
just as a reference you can see how well
it's functioning you can see what an
encoder should look like and so I'm
going to start with this now again as I
rotate this if I were to rotate this one
full revolution we should hear this pin
short out about 24 times and I'm not
gonna do a full revolution that's
overkill I'm really only going to do it
I'll do it a half revolution just to
show my point so I'm at 6 o'clock right
now I'm gonna rotate it to 12 o'clock
simulating about a half a revolution we
should here about 12 shorts to ground so
let's do that now so that's a half a
revolution you can see it's now at 12
o'clock and I don't know if you counted
but it was exactly 12 counts so this is
a perfect example of what an encoder
should function like I'll switch the
multimeter pin my lead to pin 1 of the
volume encoder and we can test that all
right so we're hooked up there now again
I'm at 6 o'clock and obviously this is a
larger knob but still again it's 24
pulses so as I rotate it a half a
revolution again I should count 12
discrete steps so watch what happens
as I rotate this
so hopefully hopefully you can tell that
it's not seeming very normal right now
it's not acting at all like the trouble
control was I've only turned it about a
quarter of a revolution and it seems to
be shorting out and going open
intermittently and so I'll continue on
just to the half a revolution point I'm
going very very slow obviously
so that's about a half a revolution
right there and you can tell it was
really didn't sound anything like the
trouble control so I'm still very very
suspicious of the volume encoder and so
at this point I'm going to try and
remove it from the board and so we can
inspect it it's possible that we can
open it and clean it if there's
something physically broken inside it'll
probably be a lost cause and I'll have
to try and find a new one but let me get
this off the board and we can inspect
here's the volume encoder removed from
the unit it's always a good idea before
you replace or tear something apart to
test it outside of circuit I just did
that and it tested exactly the same as
in circuit it's not even worth showing
because I tested it identically and so
I'm still very confident that there's
something wrong with this
I've never taken one of these apart
before but it looks fairly
straightforward it looks like there are
four pins two on either side sorry about
that focus and once I remove those this
green package should separate from the
metal package and we should be able to
see what's inside right I removed all
four tabs from this cover and I removed
it from the encoder and to my surprise
this looks to be physically intact which
is great I think we're gonna be able to
get this running again now that it's
exposed we can check out the operation
of it a little bit more closely again we
have pin 1 pin 2 and pin 3 pin 3 over
here that was the common between all
three encoders that makes contact with
the center of this disk at all times you
can see as I rotate the disk it makes
contact at all times
well pin 1 and pin 2 come in over here
on the left and the way they're able to
make contact our short 2 pin 3 out of
phase is that they're very slightly
different lengths and so you can see the
pin closer to the bottom is slightly
longer than the pin closer at the top
and so that if I were to rotate say
counterclockwise makes contact with one
of those 24 contacts jutting out from
the center of the disk just a little bit
before the top contact there and
vice-versa if I rotate it clockwise so
this is great and it looks to be
operating correctly I think there are
one or two one of two possibilities
that's causing our issue number one
is that one two or all three of the
contacts that's pushed against the disc
has lost its tension and it's not making
enough electrical contact with the disc
and so that would be a pretty simple fix
I can remove this green section of the
encoder here which houses the contacts
and I could push them out just a tiny
bit so they make a better contact at the
disc however these are really small
really fragile contacts and I only have
one of these so if I break one or bend
one out of shape too far I'm out of luck
so I want to attempt to fix it using
option one or the other option first and
so what I think the problem actually is
is there's just too much grease built up
on all three of these pins especially
where they make contact with the disc
and so it's kind of difficult to see
from this angle I'll remove this green
section of the encoder and again this
houses the contacts so here's the disc
by itself it's hard to pick up on camera
but there is quite a bit of grease on
there now we do need grease we can't
have straight metal to metal while
you're rotating this you're just gonna
build up too much friction you're gonna
you're gonna wear the metal down so you
do need some grease but I think the
problem is that the grease has built up
too much on these contacts and it's
difficult to see but there there's a lot
of buildup on there you can see it built
up on the actual green piece here but so
what I will do is I'll carefully clean
all of the excess grease off of these
pins
I'll also remove just a little bit of
the grease from the disc itself not all
of it again we do need some of it I'll
put it back together and we'll test
we'll see if that makes a difference if
not I will attempt to bend these pins
just a little bit to give them a little
more tension against the disc
I removed the excess grease from the
disc as well as the three pins and I've
also pushed all three pins out just so
they make as much contact with the disc
as possible but still the encoder was
not functioning as it should and so I
removed it from the unit and I've
replaced it with the encoder that was
previously in the high frequency or
treble control position so that's
currently in here now and as you can see
it's working just perfectly so this
encoder was definitely the issue and so
I'm gonna scrap that I actually like the
way
de tented style and coder feels so I'm
gonna leave this in its place and I've
just ordered a replacement for it I've
ordered several actually and I'll
replace it once it comes in in the
treble control position and so while
we're waiting we can troubleshoot any
remaining issues that we have
so I've identified the next problem we
need to tackle I'll turn the unit on and
watch what happens as I measure the AC
voltage on one of these speaker
terminals so we're at about 1.3 volts AC
and I can decrease that by turning the
volume down and it does fall to a
tolerable level of less than 5
millivolts but still when we power that
unit on we have a lot of AC voltage out
of the speaker terminal so that's going
to produce simply humming in your
speakers and I've checked all of the
outputs it's just one of these
center-backs
that isn't that doesn't have the AC and
I think that one's actually just dead so
we're gonna have at least one more
problem to resolve let's take a look at
the schematic and next and see where we
might want to start probing since we
have a common failure across all of the
outputs we want to look for a common
source and the most likely common source
of AC voltages from the power supply
section so I'll probe all of these DC
outputs from the power supply section
I've already checked the power board and
all of these outputs are very easily
accessible so we'll probe each
individual one until we come across one
with AC voltage all right so I believe I
found our AC voltage source this is the
analog 5 volt pin and as you can see we
have about 800 millivolts of AC and
that's a 5 volt rail so even if we look
at the DC voltage we can see that's
pretty low as well 4 point 4 volts DC
this is regulated by a 7805 5 volt
regulator and these are usually very
very accurate within a few one
hundredths of the set point of 5 volts
so it should be no worse than maybe four
point nine eight volts and no no greater
than five point zero two volts so this
is way often DC and it's our AC source
as well so the 7805 that regulates this
5 volt analog voltage is right here this
is IC 1053 and we know the input and we
know the output is about about 800
millivolts of AC let's take a look at
the input you can see we have 2.3 5
volts of AC voltage on the input that is
much too high we cannot expect that
regulator to be able to handle that kind
of AC voltage and so this is our problem
now since the regulator has an input AC
voltage we know that there's something
going wrong before the regulator and
there's only one thing really that can
go wrong before that and that's the
smoothing capacitor C 1080 which is
right behind the heatsink here and
physically it looks okay but my
suspicion is that it's going or gone bad
and so AC voltage on this analog 5 volt
rail makes sense for the failure we're
seen the analog 5 volt feeds the DAX and
so if we feed an AC voltage into a DAC
on the analog side we're going to get AC
voltage out and so that's what's giving
us our AC voltage so I'm going to
replace C 10 81 thing I did while I was
checking for a baseline I looked at all
the other 7805 or the 5 volt regulators
I looked at their inputs and outputs
there's two over here
on the left hidden behind the multimeter
they had virtually zero AC input and
output about one or two millivolt each
the this one right here this is the
digital five volt you can see the output
if I can get my probe on there the
output AC voltage is only one millivolt
but it does however have a bit of AC on
the input 115 millivolts so although the
regulator can handle that I think that's
a sign that that smoothing capacitor has
gone bad as well as going bad C 1088 and
we might as well replace that as well so
I'm going to remove this power board
I'll remove the two capacitors in
question we'll inspect them will check
the ESR and regardless I'm going to
replace them before we fix this AC issue
I want to show you what sort of impact
this one-and-a-half AC volts has on the
speaker so I'm going to turn it on I
have no input but I have one of the
speaker's connected and you can see what
it sounds like yeah it's a terrifying
noise so we need to get rid of that I
believe removing and replacing C 1080
will do that alright I have C 1080 and
it's replacement here on the left and C
1088 and it's replacement on the right
the C 1080 or 47 hundred microfarad at
16 volt replacement is a little bit
bigger it's quite a bit bigger the
replacement I had isn't exact it's forty
seven hundred microfarad at 35 volts
versus sixteen so that'll work just fine
and the spec for that is no greater than
0.05 ohms and you can see we're well
inspected 0.02 ohms so now we can see
how bad C 1080 was that it was giving us
two volts of AC 11 ohms ESR absolutely
terrible definitely needed to be
replaced let's take a look at C 1088
this is the replacement it's an exact
replacement ten thousand microfarad at
16 volts spec is no greater than 0.03
ohms
we're well in there at 0.02 and again I
didn't think this one had completely
failed but it was on its way out as we
did have some AC voltage on the input of
that 5 volt regulator and indeed
we're at about 0.9 ohm so that one is
failing spec as well so both of these
need to be replaced I'll replace them
now I'll reinstall the board and we'll
verify that our AC issue on the outputs
is gone I replaced C 1080 and C 1088
I also replaced the high frequency or
treble control encoder since I have
everything back together I must be
pretty confident that it's going to work
so let's turn it on and see if we have
any more AC on the output no AC let's
make sure the trouble control knob still
works it does now let's do a sound test
[Music]
sounds pretty good this one is done I
appreciate you watching again please
consider joining me on patreon if you
like to see more videos like this we'll
see you next time
[Music]
you
[Music]
