DR #25 - NAD 1155 PreAmp Troubleshooting and Repair - Part 1

Duality Repair
132 followers
2 Video Views·Mar 12, 2025
This is a short video introducing the NAD 1155 PreAmp I'm servicing. There are 2 obvious problems, one of which I resolve in this video. Part 2 will be coming soon.
hi and welcome to duality repair this
time i'm going to be looking at this
nad 1155 stereo preamp
and i'm going to be using my nad
712 stereo receiver on the bottom here
as the amplifier
the preamp was sent in by a viewer and
he said that he
has recently come upon some distortion
from both channels
i have tested this initially and i don't
hear any signs of distortion
i only hear one problem and that's the
volume and balance knobs over here are
producing a lot of static
only when you're increasing or
decreasing the volume or adjusting the
balance so
i'll let you listen to a little bit of
music without adjusting the knob and
then we'll adjust and you can hear what
i'm talking about
so i'll adjust the volume knob first
[Music]
hopefully you can hear that static now
just the balance knob
yeah you're not going to pick that up
that's much more subtle but it's still
there
it's just the volume
[Music]
sounds really good though so
what i want to do is first hook up a
signal to the input
and take a look at the signals of the
output on a scope
and see how clean they are and we'll see
just how bad
the static that's being produced by the
volume of balance knobs is
here we are at the scope i have a 500
hertz one volt sine wave at the input to
the preamp
and here's the output from both channels
this is about six volts peak to peak
from each channel and you can see that
the sine wave looks very very clean
there's no signs of distortion here and
so let's take a look at the
noise and the static from the volume
knob so i'll adjust the volume knob here
and you can see that top channel
especially is very very noisy
very staticky as i adjust the volume
knob doesn't show up as much
when i adjust the balance knob that's
the balance there
and it doesn't show up very much but
there is some there as well
it's mainly that volume knob that's very
staticky so
at the very least we're going to need to
open this and we'll
clean the volume and balance
potentiometer we'll also inspect the
unit
to see if there's any other components
we may want to replace while we're in
there
here we are inside the unit and this
thing is extremely clean
so hats off to the owner for keeping it
in such good shape i don't even see any
dust bunnies hiding in the corner so
great job with that
i've looked around a bit i don't see any
signs of previous work being done
which is great here is our volume
and balance potentiometers down here
the volume potentiometer is actually a
four pin or four contact potentiometer
so that'll be interesting
i could clean this and test it in the
unit but that wouldn't be any fun so i'm
going to
desolder this and we'll we'll test and
clean it outside of the unit later
the only failure that i see or potential
failure is this capacitor right here
this is c601
so you can see how dark looking it is if
we compare it to another capacitor of
the similar type
these light yellowish tan looking ones
you can see that this one obviously had
some sort of issue
it may not necessarily have failed but
it certainly has
seen some excessive heat we'll test this
later
regardless of how it tests i'm going to
replace it this is part of the power
supply section so you can see the fuses
here
obviously the input we have our three
taps from the transformer here
our main smoothing capacitors here and
then this is the bridge rectifier so
this capacitor is part of the power
supply section
we'll definitely want to get that
replaced regardless of how it tests
i've looked around at all of the
electrolytics there are many as you can
see
on this board i don't see any signs of
leaking or bulging capacitors
although these are all original and they
are 85 c rated
and so it's a good idea to replace these
if the owner wants me to
i'm going to spot check maybe 25 to 50
of these just to see how they're testing
at least for esr
if a good percentage of them are testing
high i'll suggest that we replace these
if they're testing okay i'll probably
leave them as they are
it looks like i should be able to have
access to the bottom of the board by
removing the
bottom panel here so i'm going to do
that now
the bottom cover came off very easily
after only having to remove six screws
as expected the bottom of the board is
very clean
but before we inspect thoroughly and
test some of the capacitors
i want to fix the volume and balance
potentiometers first
that's going to be down in this section
here on this separate little circuit
board
i've already desoldered all 14 pins so
go ahead and remove that
and we'll remove from the unit we'll
inspect
clean and test it here is our volume
and balance potentiometer assembly you
can see we have four sets of pins
so the two sets of four pins are the
volume control for the left and right
channel
and the two sets of three are the
balance control for the left and right
channels so each channel has its own
adjustment potentiometer potentiometers
utilize three pins
two for the outside so in this case it
would be pin one and pin three
and then the center or pin two would be
the wiper
this style is very similar so you still
utilize pin one and pin three as the
outer pins with pin two as a wiper that
gives you one resistance range
you can also utilize pin one to pin four
with pin two again as the wiper this
gives you a different range
so effectively you have two different
potentiometers in one package
my initial thought with this was to
perform a test
before cleaning it to highlight the
static then
perform the cleaning and perform the
same test after to show what kind of
effect the cleaning had
however my multimeter is not precise
enough to show the noise i already
hooked it up and tried it it did not
work so i'm just going to clean it we'll
reinstall it and i'll run the same test
that i did before i'll hook the output
up to a dummy load
with a 500 hertz one volt peak to peak
sine wave at the input
should be able to see if the noise is
gone that way
if anyone is wondering this is what i
use as a contact cleaner crc qd contact
cleaner
there are many different types many are
sufficient this is just what i use
it's really nasty stuff that's why it's
so good so i usually use this outside if
i can
just for health and safety concerns so
i'm going to get this cleaned up
reinstalled and we'll test
the potentiometer has been cleaned and
it's remounted let's get it soldered
back in place
i'll clean the board up a little bit
with some ipa and q-tips as well
uh
welcome back to the scope i have the
same 500 hertz one volt peak to peak
sine wave at the input of our preamp
the output is shown here from each
channel on the scope
so i'll now adjust the volume knob up
and down on the preamp so we can verify
that the static issue has been resolved
looks beautiful there's absolutely no
static scene on either channel so that
problem is gone
join me on the next video where we'll
take a deeper dive into the circuit
board
and the schematic we'll inspect that
apparently blown capacitor
and likely replace it and also inspect
the esr of several if not all of the
electrolytics to see if we want to
replace those
and we'll take a thorough look around
the board to see if there's anything
else we might want to replace while
we're in here before we send it out
thanks for watching
