Thank you to everyone who has been supporting our channel! If you use the link below before you purchase anything on Amazon, we get a royalty for sending you there, thank you!
Our store is located at 139 Caldwell St., Rock Hill, SC 29730.
ladies and gentlemen this is Joe's
classic video games back with another
really cool arcade game video for you
this is gonna be a repair video and this
is the very first part of it we thought
we'd film we've had this pinball machine
for a long time in storage we bought
this off of a gentleman years ago with
about 15 other games and this one was
basically assumed to be a parts game
because it's just been completely gutted
we're looking basically at an empty
cabinet and wasn't even in that great of
shape as an empty cabinet but we got a
few parts together and we decided you
know what we're gonna actually gonna
save this thing so we figured we'd film
a little video to show you what we're
starting with now we've actually cleaned
it up a little bit already so it looks
rough but it was even more rough before
we started working on it these are the
during shots not the before shots this
is a valley lost world from 1978 I
believe may be 1979 it's a really fun
game whenever we got it the it did have
a play field but the play field is
completely trashed basically the story
with this game is somebody left it
outside in the room literally so the
cabinet is fairly solid but the play
field actually had rain on it so it
warped and rusted and just had a lot of
problems so we what we've been waiting
for is to find another play field and we
were actually able to find another play
field so we're gonna do a complete play
field swap on this which isn't really
all that fun and takes a lot of time and
it didn't have a back glass but we were
able to find a back glass as well so if
you've got the back glass and you've got
the play field and you've got the
cabinet you've got a game all the other
stuffs just just needs to be pieced back
together but basically we're starting
from scratch so
just if we'll run down a little bit of
what needs to be done the cabinet still
needs to be cleaned up we probably won't
repaint much of it because of the
stenciling still pretty good on it and
it's pretty solid coin door needs
cleaned the shooter rod is missing the
playfields missing we'll get to that in
a minute
everything here is decent though it just
needs work
you can see on something like this see
this solenoid that's the knocker see the
rust on it that's basically the shape
that the entire play field was in so
this well what seized but now it's
starting to work basically everything on
the play field was like that so all of
that needs to be reworked and replaced
and bla bla bla bla bla the harness the
little bit of the harness that's left
has been partially hacked so you can see
they've got a ground wire I'm running
from here that runs up to the coin door
and they've soldered that in to another
wire and there's some little stuff like
that going on the back box is missing a
course but we were able to find one
that's the light panel it's actually in
decent shape all of the connections for
the displays are still there if you look
at the back of the light panel all of
the light bulb sockets appear to be in
decent shape these Bally sockets had
issues anyways but all of these look
pretty good the ones that were on the
old playfield are all just rusted and
destroyed so I'm gonna have to we're
going to use basically the harness off
the old playfield and we'll have to put
all new sockets and things on their
replacement plate though but lucky for
us the wiring on the light panel is
intact everything looks complete all the
connectors are still there now on these
connectors a lot of times you have to
repin them replace the pins depending on
the condition that they're in where the
displays slide in the front and the
slides down on the back of it but all
that looks good so over here
this is where the lightboard resides so
these two connectors here look fine
again they may need to be repaired but
they're there and then here's the two
connectors for the power of the NPU
board and they look fine but will
probably need to be repend
the harness continues around the top
runs over here to this where the
solenoid board resides and one of the
connectors is fine again may need to be
repend but this one they've completely
cut off why would you do that
hmm why would they do that to me so
we'll have to repin that and put another
connector on and then you've got the
problem where it may be too short to
actually fit where it goes
hopefully it'll make it and then this
crap down here look at this they've got
this is the this runs to the soundboard
that goes right here now but deal with
the board's been missing these are all
exactly the same in all of the valley
machines the soundboard is a little
different but it's not a big deal that
we've got some of those so the NPU board
we've got those the light board we've
got those the solenoid board we've got
those and they're not that expensive to
us the sound board we've got that so all
this is fine the power supply that goes
here is missing they've got it tacked up
or I believe it's a hack I mean I
haven't seen it like this but they've
got this plug here I've never seen that
in a Bally machine that's off of an e/m
so somebody's added that unless unless
it was like that in lost world I've
never seen a lost world like that and
then they added this large power
connector here which is actually
supposed to go on the power board right
here but that's not the right connector
so I don't know what they did there
either
maybe the power board they had had a
they had hacked and put this connector
on so they could plug it in but that's
not what you usually see in a Bali so I
don't I believe that was all added later
so all of this needs to go I'm gonna
take this out I'm gonna take this out
put a new connector on that properly
fits on the power supply once we get
that in there again that goes there
there's all
some other connectors one-two-three-four
five-six-seven-eight there's about eight
connectors well I guess some of those
would be on this harness yeah so this is
more of the cabinet so basically this
will go up here on the solenoid board
this is one of the connections maybe two
cabinet switches or whatever I don't
know now figure out where it all goes
but these these three connectors here
actually look pretty decent and although
that one's burnt so that connector will
need to be replaced and repend so you
know we're starting from scratch on this
one basically a game like this to be
honest isn't really even worth don't
going through all that trouble but we
really like working on them and since we
already owned the cabinet even though we
bought it as a parts game there's really
no value in it as a part nobody's gonna
pay anything for the cabinet and there's
really no basically either we can trash
it basically throw it in the trash or we
can put in a little bit of work spend a
little bit of money and make it a
freakin pinball machine again so guess
what we're making it a freakin pinball
machine again what do you think about
that so there's the cabinet that's what
we're starting with and I'm gonna show
you the playfield that we picked up so
you can check that out be back in just a
minute
alright folks so here is our play field
we picked this up off of a gentleman who
back in the day worked for an operator
that actually did play field swaps so
this was in a course used in a machine
and then they back in the day you could
actually go order new play field so
experience as apart from the operator so
he his operator would basically order
replacement play fields and swap them
out every once in a while which is
craziness because there's so much work
involved but that's the story that he
told us
and again I've got a parts playfield
that's destroyed I mean horrible shape
the one that was originally in this
machine and was left out in the rain but
it's got all of the little pieces it's
got all the little posts it's got all
the little brackets and assemblies and
everything and most importantly it has
the wiring harness which is probably the
hardest part to remake you can buy
almost every part that you need for this
playfield to completely populate it from
what you see here but the you can't
really get the wiring harness you'd have
to make that from scratch and that would
be quite an undertaking so we're happy
to have that original harness to help us
along but this is what we're starting
with it's not in perfect shape we got
this pretty inexpensively as you can see
there's somewhere here and there will
probably touch that up get it looking a
little better it hasn't even been
cleaned but we'll see what we come up
with even if we have to leave it with
that wire in the center it'll be a lot
better than the one we got believe me I
know you're dying to see it but uh out
of respect for Humanity I won't show you
what it looks like so there you go that
is our starting point and our play field
that we're beginning with and this is
sitting in our showroom we'll let people
come in and do an eye over it as we work
through it it'll probably take us
several weeks to we won't work on it
straight through we'll do a little bit
here and a little bit there a little bit
here a little bit there until we
actually get a nice decent machine up
and running again but we'll film little
updates and let you see along the way
just so you can see kind of how it's
coming along everybody root for it
because this thing is going to need a
lot of help all right we will see you
soon on the next video
all right folks we're back next thing
we're gonna do on this lost world is we
need to replace the power supply so we
were able to find a used one you can't
get new ones that make new rectifier
boards but they don't make new
transformers these transformers output
several different voltages and the
rectifier board rectifies all that with
the three bridge rectifiers so we've
been working on this power supply what
about this used the main thing that you
need to do on these is the connectors
usually need to be replaced
so we put all new connectors in need to
make sure that the fuse holders are in
good shape and they are and the fuses of
course are good the two sand resistors
sometimes will burn up on this
particular parts the part both of these
were missing so we put new ones on this
one's a little bigger than they usually
are usually a little smaller but as long
as it's the same value or slightly more
you're fine so we've got it in now the
three bridge rectifiers are right here
right here and right here a lot of times
you replace those two these ones are
still working good so we're gonna see
how that goes you can replace those by
putting bigger ones on the top but these
are fine so we're gonna leave it for now
we usually don't have too many too much
trouble out of that but so there it is
nice little rebuilt power supply for it
so well we'll throw it in the machine
and then we'll work on some connectors
alright folks so we got the power supply
mounted in there and I put a brand new
connector on that first connector which
is the one that inputs all the power
from the wall buh-buh-bah into the
rectifier board which in turn sends it
down to the transformer and the nerd
fire rectifies it once you get that done
you need to check all of the test points
so we've got five of them here so I'm
gonna check them slowly I've got this
ground probe precariously placed in
there basically you want to check in on
the bottom leg of this resistor is where
you get your ground so we're gonna test
test point one we're getting six volts
DC that's where your switched volt
lights which is like the playfield lamps
and stuff that turn on and off and then
the second one here test point two we've
got a hundred eighty five volts that's
the that's dangerous but that's the
voltages that ultimately goes to the
score displays whenever you don't have
any of the other connectors plugged in
you're going to get a low number like
that like 180 170 something like that it
actually turns into 220 once you plug in
the regulator board and when you check
all these they don't need to be exact
because they're not regulated yet
because they haven't gone to the
later gorgeous so if they're irregular
slightly that's no big deal so test
point three thirteen votes that thirteen
votes is going to get turned into five
volts on the regulator board which is
going to make all of the other boards
work and then we'll skip the fifth one
for a second the fifth test point forty
six point four volts DC that's your
solenoid stuff like the flippers and
stuff like that and then test point four
the reason we see get that is because
it's actually AC voltage and so test
point four is 7.5 volts AC that's what
actually makes all of the run straight
to the playfield to make all the
playfield lights work and all of the
bakbox lights work the ones that are
general illumination so we've got that
and we've got the first connector repend
now next i'm going to have to figure out
what to do with this connector to make
it actually fit where it's supposed to
go down here because that's how we're
going to get power up to the regulator
board and over to the NPU board so I
think all the wires are a little short
so I'm gonna be pinching and pulling a
bunch of wires so we'll see how that
works out but I'll be back after we
figure that out alright folks so we're
back now what I did we spent about two
hours on this again this machine's
probably not even worth all this time
but we're gonna do it anyway I replace
that bottom connector remember it was
completely missing
we took this junk off of there I don't
know even know what they were doing with
that but basically that was the the
bakbox connector and then they had that
rigged into got rid of that stuff and we
put it back the way it was a problem we
had was that wires were too short they
all were hacked up here so we put in
these two nice matin lock connectors
here that extend had plenty of new wire
and we tried to keep it as color-coded
as possible to the original and ran it
down so basically what that's doing is
now the power supply is getting the
power from the the wall and it's
rectifying all the voltages and then
it's sending it out up into the back box
now if you remember
we have a wire here and then they cut
this one so those wires are now live I'm
going to have to put a new connector on
that too but it's a lot less wire so it
won't be as big of a deal and then the
wires run across they've all got power
now and they're running over here to the
mpu and down here to the lamp board now
here's the cool part there will also be
one more connector that I need to plug
in there that'll come off the playfield
once we get it done so here's the cool
part you hit the power switch and you
get your first sign of life out of this
old game that's been sitting forever so
does this game want to cooperate
does it want to come back to life that
one light bulb says yes so this game
half most light bulbs are missing the
ones inside the little boxes there that
go behind the back glass those are a
switched bulbs so without the CPU that
won't work
but now that we've got the now that
we've got the general illumination wired
up one of the general illumination bulbs
actually still works so I thought that
was awesome turned off hit the switch on
and game that one light comes on trying
to tell you please save me I'm still in
here I want to be a lost world again so
we will do what we can do so we're
working right through it now we've got
the power supply ready to go
everything's cool with that so the next
step really that was one of the biggest
problems was that connector being all
hacked up the next step is replacing
that little connector and then getting
our voltage regulator board in there so
we will do that tomorrow and we'll film
it for you after it's done and add it
into the video see you then
alright folks we're back so last time we
had messed with the power supply and got
it all putting out the right voltages
and then we were talking about how it
needed a voltage regulator board so I
had one that was a parts board
well not parts board but untested we
broke it out
that little connector that was cut I was
able to make an all-new connector
because I was able to unravel the wire
harness a little bit and pull out enough
extra so that I could it could
everything could fit so the solenoid
board
I replaced the voltage regulator so now
the rectifier board is sending 12 volts
up and this rectified this voltage
regulator here is turning it into 5
volts which is you know 5 volts is what
basically most PCBs need to run the IC
chips and stuff while I had the Solon
wood board out I checked all of these
tip one of two transistors down here
which I'll make all of the solenoids
work and replaced a couple of them so
they're all good
I replaced the 5 volt capacitor there
all of the stuff in the this section
here creates the voltage for the score
displays it was all working and tested
fine but the voltage is really low is
only putting out like 130 volts so I
figured out that the pot there that
adjusts it was broke so I replaced it
and then I saw this cap at the top
filters it and it was really screwed up
making the voltage too low so once I
replaced that and replace that pot I got
it to where I could adjust it up to
about a hundred and seventy five volts
where it needs to be and then I plugged
this in because this has the return for
the cabinet switch the test switch
because I'm trying to get this to where
I can test displays and things like that
in it so we got all that ready and all
those voltages are right so then what it
does is it sends the voltage over this
away to the mpu board so I had an MP u
board that I already had working and
popped it in plugged it in had a good
connector already there that's the
connector for the displays this is the
connector for the cabinet switches right
there
so we plugged all that in and then we
had a light board so we plugged it in
we've got a couple wires over here that
we haven't completely connected yet so
this isn't the lights aren't up and
working yet but uh we basically now have
the whole powertrain working and the
you bored in it so then we went through
our stash and found a bunch of displays
and so we got out some displays that we
had tested previously and seemed to work
pretty good or we had labeled was
working and replaced a few resistors and
stuff I also replaced the light bulbs
that were missing or burn out I left the
one over here that dusty one since it
made the trip so long you know I left
that one in that we were looking at it a
few minutes ago so we'll turn it on and
see what it does I can reach the switch
all right so we'll see if she boots up
all right it's up and running now it
doesn't have the soundboard plugged in
yet I don't have a soundboard for it yet
but we'll get one of those and working
on it get it back how it was but I also
got this one display down here it's got
a little bit of burn on it if the
voltage is too high in the machine that
you've got the displays in it'll burn
them like that to wear a little bit of
the display will be missing so
unfortunately that one's like that so we
put it in the fourth player this because
it gets used less and we might replace
that with a with a little bit better one
too so we'll put it in test mode and go
to the to the display test there we go
so got all good displays got the general
illumination lights in the back box
working got most of the board's and that
we still need to do the sound board and
of course the playfield is just a bear
piece of wood there's nothing hooked up
on it yet but we are getting there
progress progress progress so be back in
just a second look at that we were able
to pick up a really nice back glass for
it not really nice but nice enough we've
been saving this for a while because we
knew we had to game in parts and storage
so that's one of the reasons we want to
fix it cuz look how nice that back glass
is
man that's a heck of a game just looks
really cool look at the art on this
thing it's all intricate
with the dragon and the woman and the
guy and the horse check that out so this
is gonna be a really cool game once we
get it up and running and we got you
know got a lot of it done got the power
supply work and obviously got the game
board up and running to where the game
is actually in a track mode right now we
just don't have a light board all the
way hooked up that turns on like the
game over light and stuff like that and
we don't have the sound board hooked up
but it's getting there so there you go
so now in this video we'll do another
video in the future showing you us
working on the play field and the
cabinet a little bit and but then we'll
have a little bit more of the
electronics figured out in the back box
like the the sound board and the we'll
get the lamp board up and running
by the time we get ready to work on a
play field we'll shoot a video for you
so if you like videos like this
subscribe to us here on youtube or you
can if you're looking for a game check
out our website lions arcade dot-com and
it shows you all of the games we have
for sale right now we've got a showroom
here in downtown Rock Hill South
Carolina which is about 15 minutes south
of Charlotte North Carolina full of
arcade games and a few pinball machines
for sale but we keep a list of
everything we've got with pictures and
prices and everything on our website at
all times to go check it out no matter
when you're seeing this video and if
you're local stop by and see us you can
check out the selection in person now
maybe you don't want to buy a game and
maybe you're not a local where you can
come check us out well that's cool too
just subscribe to us here on YouTube and
you'll get an email every time that we
put up a new video so we will see you on
the next video