I'm Tom Johnson, Thomas Johnson Antique Furniture Restoration in Gorham, Maine.
Well, the third floor renovation is coming along great. We've got the floor down and finished,
and that in fact has freed up this whole end of the shop. So before the shop renovations begin,
I hope to get back and finish up the work on my desk. And in fact, the shop renovations have
already begun. I said goodbye to my trusty parks planer, and this table saw is going to go next.
I'm even selling my truck. But wait, there's more. It's definitely springtime here. I mean,
it's really wet out there. But hey, we don't mind. The birds don't mind. And it's great. All the
animals are emerging. And speaking of wet, I think everyone's experienced water damage to a
piece of furniture. Usually it's plants with inadequate saucer underneath. Coffee cups are
great, but anything can happen. Let's take a look at a couple of videos on jobs that I've tackled
with water problems. So enjoy these videos, subscribe, like, share. I'd appreciate it.
This is a nice old drop leaf table. It's a gate leg table. And I think the top appears to be made
of birch. It seems to be very old. I might get a better idea when I'm working on it, but it
certainly appears to be old. The base is made of various woods. The drawer certainly gives the
impression of being very old, big, single kind of crude dovetail. This table has been refinished
before. And the main thing that complaint that the customer has now is just this surface here.
It's been very, very badly stained. So what I'm going to do is refinish the top.
I'm going to try not to sand this top very much. I'm going to sand it some,
and then hopefully some oxalic acid will take these stains out. And then I'll refinish the
whole top and make it look a lot better. I can see that there's new screws holding this top
onto the base. I also see cutouts here for hinges. Right away it makes you
think, well, the top's not original to this base. The top seems sturdy on this base. I think I'm
going to not take this top off. I'm just going to take the leaves off. Doesn't seem like an old
screw. The top of it looks old, but the threads, it certainly is a modern screw. I want to make
sure that these screws go back into the same holes when I go to put it back together.
I noticed when I was carrying these leaves over, it's got a loose joint here. This could be tough
to clamp up. I'm going to see if I can clamp it, but there's so much tension there. I can see that
I might just have to put a real thin wedge in there. Boy, it's coming together here, but it
needs a tremendous amount of force. There's a lot of resistance to it coming together.
So I think I'm going to, I'm going to add an additional clamping setup here further out for
the second joint. And I'm going to make, even though the block I found seemed to work okay,
I'm going to make, I need another block for the second clamp. I'm going to make some
blocks that are a little bit better to clamp against. I also think that because of the
tremendous amount of tension in these areas, that I'm going to use epoxy to glue these back
together. I don't think regular glue would hold it. I'm just not sure. I can't clean these joints
out, you know, perfectly. I'll clean them as much as I can. And I can mix up epoxy, this color,
and I think it'll work out really well.
Now the center section of the table here has cracks in it, but I don't see any movement at
all. So I'm just going to try to work around those. So the next step is to tape off the base
so that I can strip the top. Just a word about plastic and the use of plastic. I hate using
plastic. We're trying to cut down everywhere we can. As you can see, I've already used this plastic
for one project. I'm using it for another project here, and I'll keep using it until I absolutely
can't use it anymore. And at least for right now, that's a start. So I've got a lacquer thinner here
and number one steel wool, and there's not a lot of finish on here. I don't know what's on here,
but I'm going to see if I can just take it off with lacquer thinner as opposed to using stripper.
The lacquer thinner is doing a great job of taking the finish right off of here,
and so now I'll get some clean lacquer thinner and a clean rag and just do it one more time,
and we'll see what happens.
All right, I'm going to sand this now just by hand, and I'm going to sand it with 100. I don't
like sanding antique tables with 100, but I'm just going to sand it lightly by hand. I want to cut
through just the very topmost surface. I really want the oxalic acid to be able to bite in where
these stains are. Always a good sign when the marks actually start to fade somewhat immediately
sanding. Now bear in mind, even though I'm sanding with 100, I am not trying to sand out any defects,
any unevenness. I want all that stuff to stay. I like the local sawdust I'm getting here.
Like I said, I just want to clean off a microscopic surface so that the water
into which the oxalic acid will be mixed can penetrate. Boiling water, oxalic acid,
the measurements don't matter. I'm making a super saturated solution.
Sometimes when you put the oxalic on, you'll see the black marks and water marks go away instantly,
which is always really great. It's not happening here, but you know, I'll let this dry completely
and then we'll see what happens. It's been about two hours. I can still see some of the darkness
through here. It's kind of hard to tell because the oxalic is all over, but I don't think it's
dry yet. I may just wait overnight. Okay, this has dried overnight. I'm going to rinse it off.
Well, the stains did not go away completely. They're substantially lighter. They're not black
anymore. I'm going to let this dry. I may even stick it outside in the sun. I'll let it dry off
and then later I'll sand it again and then decide whether I'll treat it again or not.
All right, while the tabletop is drying outside, as I've walked by this leaf, I've noticed that
the crack has opened up again. I'm glad I used epoxy because at least it's not moving. I've got
a piece of maple veneer here. I'm going to even make it a little thinner wedge shape and then
insert that into the crack with some high glue. All right, I've just brought this back in from
outside. It's good and dry. It looks fantastic. The stains are really, really light. You know,
it works so well. I think what I'm going to do is I'm going to sand this again,
try to kick up a little sawdust with the 100. Once again, being sure I don't want to change
the character of this, but I feel like I want to sand it one more time and I'll treat it again.
Let's just see if we can get it even better. Sometimes if you can just break up these little
circles a bit, even if they're not completely gone, if they no longer look like circles,
that will be enough. It won't be so distracting.
Okay, the spots lightened up some as you saw. I'm going to treat it again. I'm going to use
the same Exolic I used yesterday. It's amazing. You can see how much it's come out of solution.
I'll heat it up in the microwave and see if I can get it to re-dissolve.
Okay, the Exolic readily re-dissolved in the microwave, so here we go again.
I'll go back and give the worst areas here kind of an extra dose. All right, that's good. These
spots when they were wet don't look that much better, but anyway, I'll let this dry and we'll
see tomorrow. Okay, round two. Let's rinse this off and see what it looks like.
Well, at first glance, it doesn't look that much different than yesterday,
but maybe it'll be a little bit. I'll stick it outside. Once again, a lot of bright sunshine
today. Let it dry. See what happens. All right, the tabletop has been outside in the sun. It's
all dry. It looks great. The marks are very light. However, we know from when it was wet that
they're going to show a little bit more. I've talked this over with the owner of this table,
and we're not going to go any further with these marks. I'm going to sand this with 150
and I'm going to seal it with a coat of Garnet Shellac. Okay, I'll sand it up. Now,
we need to match the existing leaves. I know it had pretty good color when it was wet. I don't
think it's necessary to stain this wood. I don't think it would work very well. Maple doesn't take
stain very well. I think what I'm going to do is seal this with Garnet Shellac, which is a dark
shellac. Let's just try a little bit first here. See what it looks like. It's definitely a good
place to start. That may be it, actually. That's great. Boy, the shellac dries so fast. It looked
great when it was wet, but actually, you can see now that the color is really good. I'm going to
finish this with a tung oil varnish. I'm anticipating having to tint the varnish a little
bit, but the way this looks right now, it looks great. The shellac is really soaking in. The
stains are still there. They're not looking too bad. All right, the shellac has dried all night,
and it looks really good. The spots are all still there, of course, but
greatly lessened in intensity. I'm going to sand this with 320.
Okay, all sanded. I'm going to blow it off. I'm going to wipe this off with this product I buy.
It's called Wax Wash Remover, and it's kind of like a paint thinner. It'll clean the dust off
of here, but also it's designed to remove any contaminants, like silicone contamination that
might be on the surface. You'll notice I'm going to just wipe in one direction and turn the rag,
so I never wipe over an area. In other words, if there is contamination, you don't want to
spread it around, so do one swipe at a time. Now, I'll apply my first coat of tung oil varnish.
The color's not bad. Tomorrow, we'll decide if I want to add any color to the next coat.
All right, so 24 hours has gone by. Our coat went down pretty good. You know, it's still got
areas of unevenness. It definitely needs more coats. This is a pretty thin finish,
and like I said yesterday, this is definitely oranger than this. It always helps, even
though it's obvious it's orange. It always helps to use my little color card, lay it on there,
really look at what you're dealing with here. It's a little tough. There's so much variation
throughout this table, but definitely I got to tone down that orange. I think I'm going to
add a little raw umber oil stain to the next coat of finish. I'll experiment a little bit to see.
First, I'll go over this with just a little 320 again, just lightly.
Well, it definitely kills the orange and browns it up. I hope that it's not too much. I'm thinking
maybe I should thin it out with a little more finish. Maybe I put a little too much stain in
there. I think I will, although as I pat it off here, I think it looks good. Maybe that's what
I should do, brush it on and pat it off. It's not like it's an exact match, but it's just so hard
to say. There's so much variation and figure in the leaf, and this is like really different wood,
but I like it. At least it's not more orange than that. When you're trying to match colors or make
things go together, the most important thing is that this is not redder than that or oranger
than that. I think I kind of like this. Maybe I'll pat a little bit more. I'll do the other half,
and it's got a really nice color to it. I think it'll work well.
All right, I'll let this dry and then evaluate, but looking from here to there, I like what I'm
seeing. Okay, dried overnight. Now, I notice standing from this direction, the center section
is a lot better, but it's still a little orangey, maybe a little more yellow, but looking this way,
it just looks really good. There's so much variation in this table. I think I'm going to
leave it alone. I'll put my final clear coat on. I'm just going to go over this very lightly with
some 500 paper. Before I put on what I hope is the final coat on this top, I'm going to finish
my touch-up work and clean these and give them a light sanding and give them a final coat at the
overnight. I'm going to see if I can rub them out with some steel wool and wax.
The top doesn't feel perfectly smooth. It has little nits in it, so first I'll go over it
with a piece of craft paper that's cut from a paper bag. Now, I'll go over it with dry steel wool,
4-0 steel wool. So, what this dry steel wool is doing, I'm just kind of evening this out. Remember
these two leaves, I just put a single coat on. There's a few spots where maybe the finish was
a little thin. I'm definitely not going to put another coat on them, but this dry steel wool
evens them out. So, now I'm going to continue with the 4-0 steel wool, but I'm going to use
it with the beeswax orange oil polish.
Just an aside here, when you're looking at the underside of the table, you can often get a lot
of really good hints, or more than a hint, as to what the original color probably was like.
You can see that right here on the underside of this leaf and this board.
Well, there we have it, a very nice antique gate leg table. There wasn't a whole lot wrong with it,
except for the center section here. It was a mess with some really bad black stains.
This is a good lesson when you have to refinish an antique. I couldn't get rid of those marks.
I tried with oxalic acid. They greatly lessened. They did not go away, and I'm glad I didn't do
anything else, because ultimately these marks really helped it to look like the rest of the
table. It came in, the color is good. I have about 12 and a half hours in this project,
and I think it looks pretty good.
I'm Tom Johnson, Thomas Johnson, Antique Furniture Restoration in Gorham, Maine.
This is a very common oak barrister bookcase. They're pretty neat. It's not in bad shape.
We're going to clean it up and put it back together, but what this video mainly will
concentrate on is I do have to refinish the top. It's got a lot of bad water stains,
and I'm going to use oxalic acid to get those water stains out.
I've stripped the top just using regular paint stripper. I washed it off with TSP.
You can really see after it's been stripped the water damage. This top is veneered,
but I'm going to sand it very carefully, but with 100 grit paper. I want to cut down
through the uppermost layer, kind of expose some new wood so that my oxalic
will absorb and hopefully take these stains out. I just want to see a little bit of solidness
coming up so I know I've got this wood cleaned off really well. Okay, I've sanded the whole
piece with 100. Now I'll mix up some oxalic. I just run the tap water as hot as I can get it.
This tap water gets pretty hot, which is good. I don't do any precise measurements. I'm going
to put about 16 ounces of hot water in here and like a half of this 8 cup measure of oxalic acid.
Now I'll brush on the oxalic. You can't just put it on the spots where the rings are. You've got
to do the whole surface and I can't really keep it off the sides so I'll do the sides too.
It won't change the color. Now I've been keeping this wet for about a half an hour or so. In other
words, I've let this dry overnight. I can still see shadows of some of these rings. That's a
disappointing. What I'm going to do is rinse this off really well. It's important after using
oxalic to rinse it off well. Okay, I've let the top dry. The rings are still very faint but I'm
going to see if they sand out. All right, I've sanded this really well with 100 and 150. I
certainly can't see much of the rings. The next step is to stain it. Sometimes when you stain it,
the rings or spots may reappear somewhat but I know I've gotten them off as well as I can.
All right, here's the moment of truth. Let's see what we've got. This is great. Really,
I don't see any trace of the rings and water spots. There was a spot here that was the biggest ring
and then a bunch of spots over here. I'll seal it with a coat of shellac and then I think I'll give
it a couple of coats of polyurethane in case somebody decides to put plants on this thing
again. Okay, here you're going to see with the top all done with some finish on it.
The spots are completely gone. It looks pretty good.