Restoring an Antique Mirror

Thomas Johnson Antique Furniture Restoration
41 followers
105 Video Views·Jun 27, 2026
Tom Johnson of Thomas Johnson Antique Furniture Restoration in Gorham, Maine . Tom has been restoring furniture professionally since 1979. Visit our website at http://www.thomasjohnsonrestoration.com, call us at (207) 222-2266, or write us at [email protected]. And for those on the west coast looking for custom framing, be sure to check out Tom's daughter's shop, https://www.emcollier.com (@emcollierframes on Instagram).
AI Generated·May contain errors
I'm Tom Johnson, Thomas Johnson Antique Furniture Restoration in Gorham, Maine. I like this video
where I carve some missing pieces for a mirror frame. I really like these
antique Victorian frames with the applied carving, but the carvings are prone to break.
I point out in this video that I am not a carver. I have only about a dozen carving chisels and I
very infrequently need to carve, so when I do need to carve it's always like
starting over for the first time. But what I have learned over the years, the most important thing
is to learn how to sharpen those carving chisels and to keep them sharp. I hope you enjoy this
video and if you do, hit like, subscribe, share it, comment. I'd really appreciate it.
This is a nice little antique frame, late Victorian, late 19th century. It's made of
solid walnut and it's got a real kind of a woodland motif here with these leaves carved.
And the problem is that some of the carving is missing. So here you have a piece missing.
I'm going to number these, make it easier to do before and after shots. This piece is
broken almost in the identical place as the other one, right near the nail. This is a smaller piece
and the fourth one is, that's a big piece of putty or something there, so it's even
a larger repair piece than the others. This intact corner is a bit loose. I'm going to see if I can
get it off of there. That'll make it really easy to measure the thickness and trace the shape.
These are tiny square cut brads. I'll see if I can't tap them out. Good thing I swept the floor
this morning. It looks like 9 30 seconds of an inch or 4.6 millimeters. I found a nice thin
piece of walnut in the scrap pile. I still got to plane it down some. The original piece,
the grain was running this way. In other words, they made this out of one piece of wood
and the grain runs this way. Then, of course, that's why they broke across the short grain.
My repair piece is, I'm just going to run the grain straight. I'm a little bit short in this
area here. Before I glue this down, I think I'll try another one, see if I can get better at
finding where this joint should be. Okay, that's where I think the line should be. This time I'll
cut it back a little bit, give me better chances to fit it. Yeah, see the first piece I tried too
hard to cut at the right angle. Now I've got extra wood there. Yeah, that looks good. Now,
I like to take the ragged bits off that inside corner. Okay, I've got two more pieces to do and
I'm going to do those off camera. I'll be back to glue them on.
All right, tomorrow I can start carving. All right, all right, now the carving begins.
So
All right, I think that'll work. This is a good time to point out that this is not a video
about how to carve. This is a video about me making you think that maybe I know what I'm
doing here. All right, this one doesn't look too bad after the first one. I think
I should fill that gap before I do any more carving. Okay, I've sanded all these repair
areas with 100. Now I'm going to sand with 150 and then 220. Okay, all sanded. Now I'm going to
tape off the frame before I stain these. I'm guessing it's going to be one of three stains,
medium brown walnut, medium walnut, or perfect brown. Well, that's not bad. I could just stop
there. This is medium walnut. Yeah, just as I suspected, it could be too red. Now we'll try
the medium brown walnut. Yeah, I think the medium brown walnut is the best one. It's got just the
right level of redness. Yeah, I think it's going to work just fine. Okay, now I can glue this
carving back on. Luckily, I have my little locator pins here. Okay, let's put some shellac
on these and see what they look like.
Yesterday evening, off camera, I applied another coat of shellac, just like the first one. Now I
want to cut it back again and then apply more shellac. You can see how grainy it is. I'm going
to use 500 free cut paper here. I like cutting back that graininess with paper, but at the same
time I don't want to go through the finish and to the bare wood. So I'll do it a little with
some paper, just gently. The paper is good for getting down into those incisions,
but then I'll finish with Scotch-Brite ultra-fine gray pad. The paper is best for the edge.
All right, it's looking good. I've let this dry for two days. I think it needs at least
one more coat, so I'm going to do the same routine again.
Same routine, careful sanding with 500 grit free cut paper, then a Scotch-Brite pad,
and this time I'm going to go over the entire carving. I'm going to give the entire carved
corner pieces a coat of shellac. I'm going to set these nails. This is the piece I didn't
work on, the piece that I took off. I'm going to set these nails. Check any other nails. I'll
fill those holes with a rub-in wax stick. On this one, this is my joint and I've got a pretty good
opening there, a little bit there, a little more there. I want to fill those in with something
that won't shrink back. I'm going to use shellac sticks. Let it cool down and then I'll sand it
with a little 500. Okay, all the carvings are braided. I'm going to just give them a quick
wipe of the Mohawk wax wash remover. It just helps to remove any contaminants. This is the largest
piece that I carved. This is the smallest piece that I carved. Okay, I've let this shellac dry
for about six days. You know, we all know shellac is a fast drying finish, but you really need to
give it time to truly dry. As you can see, the shellac is very high sheen and we need to cut
that back a bit. I'm going to use a combination of pumice and this orange oil polish. I typically
don't measure, but I am for the purpose of this video. I'm going to use about a half ounce of this
beeswax orange oil polish. That would be about 15 milliliters and I'll use a quarter teaspoon
or about two and a half grams of this 2F pumice. I'll use a stencil brush. Yeah, that cut the sheen
down nicely. I hope you can see the difference between this sheen and that sheen, which I haven't
rubbed out yet. Okay, I think I can go ahead and do the rest of the carvings. Okay, now I'll go over
the rest of the frame with a little bit of the orange oil and beeswax polish and some 4-ought
steel wool. So, here we are. A nice little Victorian frame, late 19th century, early 20th
century, and all that was wrong was there were some pieces of these carvings missing and I put
wood on there, carved them out as best I could. So, I've got about six hours in this job. I use the
table saw, thickness planer, bandsaw, and these hand tools. Here's the first one. Here's the second one.
Here's the third one. And the fourth one. I think it looks pretty good.
