Furniture Restoration Restoring an Art Deco WaterFall Dresser + Soda blasting Furniture

Antique Art Deco
12 followers
7 Video Views·Nov 2, 2025
Comments are disabled for this video.
Hi everyone, it's Adam with Mylos Restoration and today I've got a video for you about refinishing
this Art Deco Chester drawers. It needs a little bit of work for sure, but I'm going to get it
fixed up. So this is definitely going to be one of the appeals of this video is this soda blaster
and I'll just go ahead and give you all the specs for it now and tell you everything that I used to
run it. The only thing that I didn't really capture here is the size air compressor that I'm using.
I'm using a 60 gallon that puts out around 18 cfm at 90 psi, which is usually what the least
amount of psi you can run a soda blaster at. And I'll say that it taxes my air compressor,
but I can run it somewhat successfully. So, you know, usually when you do soda blasting or any
kind of blasting like this, particularly with furniture, it's a little bit more time efficient
to sand the areas that you can with just like a regular orbital sander, but the little detailed
areas I try to do the blasting with. And what I can say about this is that if you can get your
hands on one of these for furniture refinishing and you have an area to use it at, it's great.
I mean, you know, it's obviously it's a cheap soda blaster. It has a little bit of problems with it,
but overall it just makes furniture refinishing more fun because you don't have to deal with the
and just honestly the process of using the soda blaster on it is really kind of fun too.
So for my day job and just for other things, I have done some abrasive blasting before,
so I kind of know what I'm doing, but I was kind of just figuring this out.
Usually what I, you know, had said earlier and that I do like to do is I just try to do the edges
anywhere where I think there might be a veneer burn through if I were to sand it with an orbital
sander. So like this rounded section right here, I'm going to go ahead and blast the whole thing.
So today was really humid and I had to take a break. As you could tell, the soda blaster kind
of kept clogging and I decided to try to blast the hardware too because they were pretty coated
with some kind of grime and it's a pretty common practice just to, you know, to use it on metal
and stuff like that. So the soda is not very damaging. It only kind of got to the areas that
were like the edge, like the softer woods. The walnut veneer was basically unaffected at all,
but the softer woods, like some of the birch and stuff like that that they use for the sides,
it seemed like it kind of took a little bit of a beating, but it really wasn't bad. I would have
used some fine grade abrasive if I could have found it, but I just didn't have access to any.
So after that, I took all of the wallpaper out of the drawers and I started vacuuming up all of the
leftover soda. And what I do is I take my soda and I reclaim it and then I sift it and just reuse it
and I clean everything off with either water or alcohol. Just, you know, whatever's available.
So I usually use a more aggressive orbital sander like a Mirka and like 120 or 180 for getting the
remainder of the finish off, but then you just got to make sure that you're very careful to
get rid of those sanding scratches. I actually had to redo a section on the top after I started
putting finish on it when I saw that there were some sanding swirls in it. So just something to
be aware of. So if you're pretty familiar with furniture refinishing, you'll probably know what
these are. These are burn-in sticks and I am not very good with them, nor do I have the best tools
for them, and I know that chances are I am doing this improperly somewhat. But, you know, my plan
was originally that I was going to do, I did two kind of layers. I used this kind of softer yellow
wax and I blended it in with it on top of the dark walnut because the dark walnut just wasn't the
color. And what ended up happening was, of course, because I never use it, my little stick that I
bought for burning in the burn-in sticks just quit working. I don't know, it started flashing like a
red light and just kind of messing the batteries. It just didn't really do anything, so I'm gonna
have to figure that out later. But I decided to put the stain on because burn-in sticks can be
applied after the finish is already done. So worst-case scenario, I'll just wait for a new
burn-in stick to come. Well, I mean a new torch or whatever to come and I'll finish up with the
burn-in sticks later after I'm done with this piece. So yeah, probably won't see that because
that'll probably take a few days to get here. This is Simon's water-based stains in dark walnut.
Well, actually it's just walnut and it's the full strength. Sometimes I water it down,
but I didn't on this one. So staining and getting a consistent kind of pattern can be something
that's kind of challenging. I just try to show the full thing here. Normally how I do things is,
I like to get the whole surface wet that I'm working with first and then I go back and make
my finishing passes over and remove the excess stain to get out any lap marks or anything like
that. Just kind of a way to help you get started with that. It can be kind of frustrating sometimes
to see, you know, towel marks or anything like that in your stain after you're done. But yeah,
I usually put all the drawers in and just make sure that everything looks consistent all together
because sometimes you'll have a drawer that's like a different kind of shade or whatever for
one reason, but this wasn't the case with that. So I put the hardware in Barkeeper's Friend and
I began mixing up some lacquer. So this is the lacquer sealer that I like to use. It's a Gemini
Pre-Cat sealer and it's pretty thick and it's got pretty high solid content, so it builds pretty
fast. After about two coats, generally speaking, you're pretty much ready to go. So what I usually
do is I'll sand between the... I'll spray two coats without sanding and then after the second coat,
whenever I'm confident I've got enough material on, I'll sand it. And what I can say about this
Pre-Cat sealer in particular and the way that I'm using it with a 1.4 on this 3M gun is that
I was even able to power sand this with a surf prep, you know, moving pretty quickly. Obviously
not staying in one area too long and I had no burn throughs on the stain. So it's a good sealer.
So at this point I'm usually sanding with at least 400 grit because you don't want to see any
sanding swirl marks in this. So this is Gemini Pre-Cat lacquer and satin and I mixed in a little
bit of dark walnut transtint and I added a little bit more of tobacco brown and I forget what brand
dye that I use. It's like something tones or like color tones or something like that.
But yeah their tobacco color is like really beautiful in my opinion and that's what I
use on this piece. It looks like really really dark right now but it dries a little bit lighter
and I just did one coat of lacquer sprayed pretty thickly and generally speaking I like to do two
but for this piece I had put on a pretty thick coat of sealer and this is a pre-catalyzed sealer
so I'm not very worried about it. Just one coat of the, basically it's a toner lacquer,
I mean for all intensive purposes it's a toner lacquer, but yeah I sprayed two
passes on each side. So what I did was I, you know, sprayed one side and then I switched the
nozzle the other direction and I made a pass kind of cross-hatching it. So when it comes to
pieces like this, you know, a lot of people, some people really like the dark finishes some people
don't, but what you have to kind of consider is that this piece is mixed wood. It's got walnut
veneer and then it had birch sides and some other kind of, you know, just really poplar,
whatever they can find for the rails. It's definitely made to be sprayed with some sort
of toner lacquer. I really don't like painting hardware as much as the next person but, you know,
these pieces would have had to be replated because even after blasting and everything
the color just still wasn't right and I could tell that after taking them out of the
barkeeper's friend they just still weren't going to look very good. So I went ahead and
with a pretty good, you know, spray paint that's kind of a gold gloss color and yeah, I mean,
this brand works really well as far as I can tell especially if you do your prep right.
So here's the finished piece and I think it looks really good. You know, I was really happy
with the color and tobacco brown and just the way that the sheen looked with the satin lacquer
and yeah, I can't wait to get it listed on Facebook and sell it and, you know, I'll have
to fix those areas in the back once the hard wax sticks come in. But yeah, if you want to see more
videos like this, please subscribe and keep watching for more antique and furniture flipping content.
