Thank you to everyone who has been supporting our channel! If you use the link below before you purchase anything on Amazon, we get a royalty for sending you there, thank you!
Our store is located at 139 Caldwell St., Rock Hill, SC 29730.
ladies and gentlemen this is joe's
classic video games back with another
cool
arcade game uh pinball machine video for
you today now if you
this is part three so if you haven't
seen part one
don't watch this and if you haven't seen
part two definitely don't watch this
but this is part three so basically in
part one we got this old lost world
pinball machine that we had had in
storage for a long time
that was really messed up looked like
somebody left it out in the ring
and we got it we started working on it
we started putting all of the
boards back in it getting everything
fixed up working on the cabinet a little
bit
and then in part two we got a play field
a used play field
that's been completely stripped of
everything and uh touched up the paint
on it
and uh we have that done so that was
video two now video three we're going to
actually swap everything off the old
playfield
and make the new playfield our give it
its permanent home and our new
lost world so uh in the first two we
teased how bad the
the condition of the play field was that
was in it and today you actually get to
see it
so we'll uh we'll start off i guess with
that so this is the play field that was
in this game
you can see that they left it out in the
rain we also have the plastics
basically we took the plastics off of it
and we're going to try to clean it up
because around the plastics it didn't
look too bad but then once you got under
the plastic she started seeing that it's
just completely destroyed
and can't be saved you've got paint
falling off of it
all over the place never mind all the
mold and everything that's on it
dirt funk everywhere rust
i don't know how long this thing was
rained on but
it's a damn tragedy if you ask me a lot
of that white is where we tried to clean
it up before
before we figured out that there ain't
no way we give it a good try folks
we try to save anything but this is
about as bad as it gets
so that's the shape it was in ironically
the center of the playfield had very
little wear and if you saw video too
we went through all this trouble because
we had to repaint the center
of the play field on the used one that
we got
so this is what we ended up with after
we repainted
the center of this one so this will make
a much nicer play field
it's not perfect you can see where we
did some touch ups
all through the middle there on the
wings and everything
but you got to admit that
is much better nine prime ground than
that
so that's what we're going to do today
we're going to start swapping everything
over
now a lot of the stuff that's on this
one we're not even going to be able to
use because look at this
look at all that i mean it's destroyed
luckily wires don't get ruined so we're
going to save the wiring harness of
course
but we're going to replace all those
sockets with new ones
we're going to clean up the pop bumper
assemblies
i don't know what's going to happen with
the switches yet we're going to take
each one off individually and try to
clean it and
replace it if we've got one and see what
we can do
of course we got to rebuild the flippers
and all of that so we're just going to
go through it slow
and see what can happen so the first
thing that we're going to do is lay them
both out
over here on our everybody's got a
pinball didn't lay stuff on right
we're going to lay them both side by
side
and start taking the wiring harness off
and then on the new one we're going to
go ahead and put the uh
the general illumination wires that
stapled to the play field back on it
so we will get started on that we'll be
back in a minute okay folks so we've
laid them both out
so we've got the original one here
looks horrible looks like crap and then
we've got this one now where this one
came from was this was taken out of a
machine
we bought it from a guy on ebay this was
taken out of a machine
according to him a year or two after the
game came out so basically the game came
out the play field started getting a
little wear on it you saw how the
how we fixed the center of it and they
actually did a complete playfield swap
back in the day
and put the game back out on the round
so it's kind of ironic that we're using
the one that they rejected to make ours
look good again but that's where we are
so whenever we got it
he had taken even all of the
uh wiring off the back
that all of the um
you can see how they use that to run the
general illumination or
basically on all the lights how they run
the power to the lights so basically you
have to
we have to put that back on there i
guess they needed it for their new
their new thing so what we've been doing
is going through and stapling it back
down
so i'll show you where we're at we're
going to do this one right here
so you can actually see where the
staples were and you can also compare it
to this side
and the staples aren't going all the way
in so what we've been doing
is driving them in a little bit with a
hammer to get them the rest of the way
down if you had a better stapler like a
stronger one you probably wouldn't need
to do this
and of course don't do that unless you
got something soft under it so you don't
mar up the whole front of your machine
i mean your play field
like i said you can see where the
original staples were
so you can kind of mimic what they were
doing
basically what this is going to do is
once we put the sockets in
the wire needs to touch the socket
that's how it gets its power
see here it went up to
ah see it does one of these ah create it
huh
and then it goes back like that
and then back like this
and then it goes straight up
and then on and on it goes we're
actually
out of the wiring so we're gonna have to
find something
i got 15 feet which isn't quite enough
so if you do this looks like i'm going
to need about 20 feet so
get 20 and you'll have a better one than
me but i'm going to run it to somewhere
and then run an extra little
piece to get it uh to get it to the end
so let's see here i'm still
down here this goes down like so
and well you get the idea so we'll keep
uh we'll keep going through it
and uh whenever we get a little farther
along we'll come back
okay folks we've been slaving away and
we finished up putting uh most of the
wire on that we were talking about and
then going through
and putting in a brand new light bulb
socket everywhere it needs one now
there's several different types there's
the
sideways type there's the the tall
type there's the shorts type
and then there's these flush mounted
types too
and that just all depends on if you want
it under the play field or if you want
it sticking up through the play field
so the way we did it was we basically
looked at all the ones over here
and took the screw out of that socket
and transported it over here with a
brand new socket
and of course we put the wire all
exactly where it was
on this play field we need one little
more piece
right there
you can see that over there but we're
getting there it's starting to look more
and more like a play field
so the next thing that we're going to do
is i'm going to get a piece of paper
and i'm going to label i'm going to draw
on the piece of paper
basically a representation of what the
back of the play field looks like
and then label all of the wires for the
lights
all of the wires on the switches and
everything i'm going to take off with
the harness
to transport over to this side so all of
the machinery and everything's going to
come off the play field with it
but all of the light bulbs since they're
soldered onto that wire
and we had to get new ones anyways i'm
going to clip every wire
and just label them make sure i know
where all i think there's 55
or something like that 55
light bulbs go you can kind of tell on
some of them but on some like you see
how they've got it right here
the green and the black and the white it
would be real easy to put them on the
wrong one
so i'm gonna make a little drawing where
i can keep that all straight
and if you didn't care as much you could
just write on the play field beside
each new bulb white and black green and
yellow whatever
but i'm just gonna do one piece of paper
so the next time you see this i will
have that harness
popping up off of there and
uh traveling over to that new play field
so be back in a few
okay so here's where we are i took off
everything on the playfield so
what i did was as i took the as i took
things loose from over here i took the
screws
and put them over here in the exact spot
that they go
and uh i've got everything disconnected
if it was like a coil i tried to take it
where the coil was off
i'm trying to get as not cut the harness
but leave as much as i can
on the old play field so i can take it
off piece by piece and clean it and get
the rust off of it and everything
um so like the flippers for instance
i've got the coil and the
end of stroke switch because that's what
is wired down here i've got the
uh out hole switch and the other coil
and then the stroke switch
the pop bumpers i mean the kickers i've
got the
coil and the switches you know and so
this entire
harness is just laying on here now so
we're going to just transplant it from
here to here now another thing that i'm
going to have to do
as i go through i'm going to have to
basically each little
point of the playfield i'm going to have
to
put the freaking t-nuts back in the guy
even took
those off so uh let me see if i can find
one where i can show you what i'm
talking about right here
it's in that little hole and then next
to it another little hole and the three
little dots around it
that's a t-nut so the one that goes
there
is this one i guess you can't see that
as that one and so it's a little
it's a little uh they call it a t-nut it
goes through the play foot a little bit
and the screw
keeps it from twisting and you use that
to mount the posts
you use them to mount the posts through
the playfield from the top side
so all of those have to be replaced too
because the guy even took those off why
did he do me like this
luckily on this play field there's not a
ton of those so
um because on the valleys a lot of their
posts they just use screws
so there are several though so i'm gonna
have to just piece by piece go through
every little thing and replace it
and uh then of course uh resolder all my
wires to it and i still have to solder
the uh
the each light socket to the wire on the
play field you don't need it just
touching like this there has to be
solder on it
so uh we will keep working it and we'll
keep documenting it and you can see it
as we go through be back
instantaneously here on youtube but in
real life it'll be tomorrow okay folks
we are moving along
nicely so we got the harness all kind of
you know screwed in and then soldered in
we've still got to put
no flipper assemblies on it or rebuilt
for assemblies i should say
uh of course all the sockets ended up
being new uh
we got our switches back a lot of the
little things that were pretty rusted i
had
other ones from other play fields like
i've got some parts play fields and
things
so like the little uh rollover wires and
stuff
some of it i didn't have like i didn't
have any extras of these brackets
but they weren't too bright too bad um a
lot of these switches
i mean the stand up switches it's a good
example here
that's the shape that we're all in all
rusted
but i had some off of some used play
fields where i was able to replace the
bracket and
some of the little metal pieces inside
so they wouldn't be as rusted
that one i ran out of them so i had to
leave one as bad as it was
but a lot of them i was able to go ahead
and replace so i'm hoping that like
whoever gets this maybe you know we're
putting a lot of time and effort into it
so hopefully down the road
someone else can put a little more time
and effort into it and money
is the most important thing and replace
some of this stuff that we haven't
replaced
if you were doing this for your home
collection you could probably just go
ahead and buy almost all of this stuff
new they make the little
the new little wires they make the new
switches
brackets like this i don't know if you
get new but you could probably buy nice
used ones
um the little bracket for the switch
they probably actually do make new that
one that i had to leave rusted uh and of
course we put
you know all of the new
gi braid in it and uh the new sockets so
that helps the pop bumpers everything
above the play field is going to be new
on those
i've got some i'll show you that over
here let me walk over here and we'll
show you the
some of the parts that we're working on
so this is the original screwed up play
field you can see things like that
from the bottom of the pop bumper that
are just destroyed but i've got a bunch
of
parts here off of other tables
and so you know what that might be my
pot bumper thing i was just talking
about after looking at my kicker thing
um so i've got these for instance
that are in much better shape so i'll be
using those
but i've still got to go through and get
the uh
either put new t-nuts in it or steal the
old ones off
it's it's so crazy look some of them are
in fine shape and some of them are
rusted all to
crap so we shall see
these big big huge ones up here for the
little uh
rebound things at the top like this
that's on the top of the play film we
also were able to remove the
wood rails on the uh
play field and put them on the new one
clean them up a little bit
you can see how they were stapled in
originally we just screwed them back in
interestingly enough the play fields
have a holes for screws
so you can screw those in but they
didn't really use them
so we're probably going to
keep this nasty play field and hang it
on the wall
and see if anybody's interested in
buying it
yeah yeah it's nasty yeah
so anyway we are getting there so next
up we're going to uh
we gotta do our flippers the two bases
for the kickout saucers
were really rusty so i took them apart
and sanded them down and painted them so
they're in the back the paint's drying
um and then we've got to do the three
pot bumpers so i'm down to
the two uh kick out saucers
the two flippers and the three pot
bumpers and then all of the little
various t-nuts that are all over the
place so that is
next be back soon okay we have put the
play field back in the case
and our general illumination works i'm
going to act like it worked the first
time but
i had to i had a one of the sockets i
had the solder touching both sides
and so it shorted it out was blowing a
fuse but i found it
but now we've got all of our general
illumination with brand new sockets
doing its thing you can see that you can
i waxed it a little bit you can see you
can still see some of the places i
touched up but it looks pretty good
we're very very happy with it
so that's where we are right now so i'm
going to start putting the rest of the
playfield back together
and then we'll see how it looks getting
closer
so we started putting some of the
plastics on
starting to look like a pinball machine
folks
okay folks we got it all buttoned up and
thought we'd shoot a little video
showing you the
end result of the playfield swamp
let's see what you think
check that out we're waiting on some pop
bumper caps and i guess i gotta fix that
one light bulb
it's always something
but we think it came out pretty good
you can see how the touch-ups we've done
really aren't that
noticeable once the glass is on it and
all of the plastics are on it and
everything's doing what it does
came out pretty decent really so
we're going to call that one done saved
it
now what we'll do is we'll we'll uh
we'll film a full-length video of us
showing all the art and uh showing how
to play it
reading the rules and then some
video so i hope you gamepl the the
series here that we did on this
showing us bringing it back from nothing
to fully working by the time we take the
video we'll have the new pop bumper caps
on it
that'll be about the last little thing
um so if you like the video
or if you haven't seen the earlier
versions of the video go check them out
on our
on our website i mean on our on youtube
and make sure you subscribe to us here
and leave a leave some feedback below
let us know what you think how you think
the play field came out
remember when i was inking and all that
stuff looks pretty nice really
not bad i think a lot of people would
have no clue that that's been touched up
but leave comments below let us know
what you think and make sure to
subscribe to us
lost world