Thank you to everyone who has been supporting our channel! If you use the link below before you purchase anything on Amazon, we get a royalty for sending you there, thank you!
Our store is located at 139 Caldwell St., Rock Hill, SC 29730.
ladies and gentlemen this is Joe's
classic video games back with another
cool arcade game pinball repair video
for you today we just we just started
working on this Gottlob Cleopatra which
is a system one game it's in pretty
rough shape and so this is the
electrical situation now these system
ones they call it system one because it
was the first solid-state Gottlob games
a lot of people don't give them much
respect but in my opinion they're very
fun games especially once you get them
where everything's working right
everything's cool but this is the this
is what we're dealing with in the back
the back box basically in the bottom
there's a much transformers usually all
that's fine and then your power runs up
here to this power supply which we're
going to rebuild runs out of the power
supply and runs the main CPU board which
gives all kinds of problems usually and
then runs they have these little
connectors on here that they've had
they've replaced with these damn things
they soldered to the board I don't know
how much of this we're going to be able
to save or how much we're going to have
to buy new but I figured let's start
with the video the first thing we're
going to do is we're going to take this
power supply off and work through it and
we're gonna replace the capacitors and
test stuff and see if we can get it
putting out the correct voltages now you
can just replace this with a brand new
one too but we like to try to save the
original ones if we can just to keep it
original and in my opinion they're
pretty good little power supplies once
they're rebuilt so we're gonna we're
gonna take that out and start messing
with it first alright folks so we have
rebuilt a lot of the power supply or all
of the power supply basically replace
the capacitors and stuff but we need to
test it and so whenever you test these
you need to make sure nothing's still
hooked up because if you get a weird
voltage out of your power supply could
fry the boards and all that fund this so
before that what I'm gonna do is I'm
gonna test the voltage is coming out of
the bottom of the cabinet
I took a glance down there everything
looked really good there's just two
transformers - bridge rectifiers and a
bunch of fuses all the fuses were fine
so I printed out the schematics for the
power supply and so we're gonna check
all these voltages over here that come
in
and we're gonna check all these voltages
over here that come out so the first one
I'm going to check is I'm gonna see if
we're getting our AC voltages in so I
should get 69 volts between pen six and
seven so this is the connector that goes
on the bottom of the power supply this
is a weird one because it's not keyed it
can go either way you can you can turn
it around and plug it in upside down and
fry half the stuff on the power spot so
the labels supposed to go up usually you
can tell if you've got an old game even
if the label is missing because all the
dust will be on the top of it because
it's been like that for 50 40 years and
the bottom will be a lot cleaner so
that's the thing we're going to check
and we're gonna check up in six and
seven here to see if we've got our AC
voltage and so between pin six and seven
we've got 75 volts so we're supposed to
have 69 so that's all good it's it's an
unregulated voltage so depending on your
wall voltage web different voltages
there alright so next up we're going to
check these voltages up here now all of
these are AC voltages V AC because it's
coming off of a transformer and I'm it's
not running through the the bridge
rectifiers on the bottom I guess those
are used to really general illumination
things like that I don't know but so
we're gonna check these voltages so our
ground is on pin three and then we can
check the other ones relative to that
right so pin 3 will go with ground so
and one we should have 14 I mean a pin 4
we should have 14 volts AC 15 point 1 3
that's good it doesn't have to be exact
pin 1 we should have 11 point 5 volts ac
I got 12 point 5 that's good
pintu we should also have 11.5 volts AC
12.5 that's good and pin five we should
have 14 volts ac fifteen point one three
so we're about a volt pile and
everything since it's AC like I said
it's not regulated so it doesn't have to
be exact your DC usually needs to be
pretty close so that means we can plug
in the power supply and so once we plug
in the power supply it's going to create
voltages over here notice I have
everything unplugged and it's going to
create voltages over here they go out to
the displays and it's gonna create
voltages up here that go to run all of
the boards so I'll plug that in you want
to turn the Machine off plug in the
power supply then turn it back on and
then we're going to test that the plugs
to see if we're getting the right
voltage all right so I plugged in the
turn off the cabinet plugged in the
bottom
thanks to that or power supply is now
getting its power and then now we're
going to test it so basically what we're
going to test it is we've got our meter
set on DC and we're going to very
carefully touch the pins on the
connectors now if you screw up and your
metal probe touches two pins you'll
short two voltages together and burn up
a bunch of stuff so don't do that and if
I don't do that if I do that I will not
upload this video so I may have already
done that two or three times and then
edited it out and you won't see it
alright so on these it's actually marked
on the little connector but you can also
look on the schematics but the common
pin is right there so I'm very carefully
hold it like that I don't know if I can
put this somewhere where you can see it
let's see if that's any better yeah
there we go
all right so very carefully hold that on
the common pin and very carefully put
this on the five volts and we've got
5.02 now I'd kind of like to turn that
up a little bit because if you got five
volts that's a power supply you're
likely to lose a little bit of power
going through your wiring and stuff so I
like it to be about 5.1 or maybe even a
little higher
it's now we're 5.18 maybe we turn it
back just a little bit
at 103 that's pretty good and be careful
what you're touching I'm up my hand rest
on the edge of it here a lot of this has
like serious voltage running through it
you won't kill you but it'll shock the
hell out of it
all right so very carefully again to
comment and on the end negative twelve
point three four it's supposed to be
negative 12 so that's pretty good now
over here is the kind of a tricky one
down here at the bottom it says four
volt DC and eight volt DC I believe on
those you have to use the same ground
that you use for the five of the 12
because it's created the same way so the
eight volt is eight point three three
the one above it is three point seven
five which is a little low I think those
are tied into these somehow I don't know
if I can adjust that or not we might
just run with it snares are common
they're 60 volts DC is 60.9 nearly
perfect 42 volts DC is forty two point
nine so basically we've got all of our
voltages the only one I was a little
concerned about was the four volt was
only three point seven five but I think
we're gonna run with it so what that
means is you're safe now you're not
putting out a crazy voltage so you're
safe now to plug in your stuff but if
you have all of this plugged into you
still have the possibility that you can
still fry stuff on the board so what
we're going to do is we're going to
unplug the driver board over here so
that nothing none of the coils none of
the lights none of that stuff is
actually plugged in so basically the
only thing that's gonna be plugged in as
our displays and our main board so it
should come up and if the board's
booting which is highly doubtful but if
the board's booting it should come up
and give us some kind of action on the
display so I'm gonna unplug the driver
board and then we'll just remember about
plugged up then we can plug the bat back
in and plug in the displays and then
we're gonna see where that gets us
alright so we course then I should
mention early on we haven't done any of
the ground mod yet which you need to do
when all this guy lip stuff we'll get to
that later but
we're just testing now trying to get
everything back up and running so we
went ahead we had the power plugged in
we plugged in the displays and we
plugged in the power running up the de
CTU board right which means now the CPU
board's hidden power
but we've unplugged the driver board so
none of the coils can lock on or
anything like that but the displays are
on and whenever we turned it on check it
out we are booted and in the game is
actually running now the only way you
can tell that the game is up and running
is that these displays are blinking if
they come up and they just have all
zeros on them you you might not be up
and running but if after a little bit
they change and you have a different
score even though it's screwed up the
CPU is basically doing its thing and I
looked up the the bridge rectifiers in
the bottom they rectify the voltage
going to the coils and then the other
one rectifies the voltage going to the
controlled lamps which is the ones on
the playfield that the computer can turn
on and off and the the general
illumination lights that are already on
just come straight from the transformer
in the bottom so basically we've got the
game up and running but you can't play
it right now because we haven't dared
and plug in any of the switches or
anything yet so all of our displays work
oh and the 4 volt voltage is the the
bias voltage for this little tiny
display here so it's working fine the
one little digits out but that's
probably because of dirty connectors
these the displays and the Goblet system
ones are pretty reliable but so our next
thing is we need to start addressing
this rat's nest of extra wires and
everything so I need to see if the
corrosion basically these originally had
a battery right here and the battery
starts corroding it leaks alkaline all
over the board and heats it up eats it
alive there's a little bit of that going
on on this one like on these resistors
here but all in all it's not very bad so
I think I can probably clean it up
if you get it up here to where it's on
to this spider chip you're in trouble
because you can't get those chips but
everything looks good so far now we
still may run into some trouble
where some of the spider chips aren't
working or something but we won't know
until we actually get the game up and
playable so we can see it scoring works
and the the switches work and the lights
work so I believe this spider chip here
they call it a spider chip because it
has so many legs
I believe that spider chip there runs
the the switches and so there's a
specular thing on Gottlob system ones
where this board here the driver board
can get a voltage can something get
short out and send an errant voltage
back up into the board and fry that chip
and if it does you cannot replace that
chip unless you pull one off another
board but if you're pulling one off
another board it probably has the chip
fried or and still be up and running so
it's just it's really hard to get those
so luckily they make a completely new
replacement board for this so worst-case
scenario if we can't get this board to
work we're going to put a brand new
board in it
I thought what we're hoping to do is
save this one like we were able to save
the power supply so we shall see but the
first thing I have to do is pull this
out and look at the basically these
these weren't here there were connectors
like this here here and here just like
they are over here so I need to see if
I've got those connectors and if I don't
I'm gonna have to order them they're
kind of weird specific ones and then try
to repin the connector with put these
wires back into the connector where they
go where it fits on like it should so I
need to see if that's possible or if the
bottom the back so screwed up that that
can't be done anymore in this boards
trash and then I need to see about
getting rid all this battery stuff
cleaning up the corrosion replacing the
resistors etc etc etc so we're gonna
start on that board and see if we can
save it so that's the next step I may be
in trouble here folks this looks bad I
don't mind the solder or that they
soldered it to it but it looks like some
of the traces are just gone but I won't
know till I start pulling the stuff off
look at this crap
this one here you don't have to use but
look at this crap so I'm gonna unsolder
all that crap and then see if it's
savable now I could leave it like this
you know you saw how they had it hooked
up but the problem is if you leave it
like that if you had an edge connector
you could leave these wires on there and
then solder it to a new edge connector
and then have a new connector that plugs
into the edge connector the whole
problem is you want this board to be
removable and then you want people to be
able to put another board in so like if
this board goes bad you want them to be
able to buy a new board just put it in
and plug the connectors right into it
you know you don't want them buy a new
board and this is what they interface
with so I don't know if I'm gonna be
able to save this or not but I'll try
cleaning this up a little bit if I can
get it where a connector can go on there
I'll leave it because it's running right
but if I can't we're just gonna have to
order new board for it either way I've
got to get in the cabinet I have to get
nice connectors that will plug onto
something either this board or the brand
new board so I'll start taking this crap
off and we'll see what we're left with
all right this is what we're left with
took all the junk off I think it looks
worse than it actually is it looks like
all the pads or most of them maybe not
that one but it looks like most of the
pads are actually still there they're
just all corroded so next thing I'm
gonna do is I'm gonna work on each pin
and try to shine it up and see if
they're even there I think they're there
it looks like the operator actually
drilled some holes through some he added
those in version looks like spider chips
fine traces are a little corroded but
now just like that let's clean up good
these chips are fine that one's fine got
a little bit of an issue here so all
that needs to be cleaned up and I don't
know if I have those exact resistors
maybe I order a man or something
but those are going to need replaced but
it's not really that bad it looks really
bad but this is nothing compared to some
of them I've seen soon we will I'll keep
working on those hence I'm gonna
literally take some sandpaper and go at
each one and see if I can get a nice
clean pad there that looks like it
worked good and then I might try to even
turn it up a little bit with some solder
to get him a little thicker but we'll
see if any that's gonna happen if that
works out then we'll be able to save it
if it won't we'll probably have to get
another board but the thing is we still
don't know if that spider chips any good
the solenoid voltage you can short to it
to where it gets up into the board
and fry that chip and so if that chips
fried I don't have a replacement one for
that so this whole board is bad and you
really can't tell until you start
playing it because I think that one
controls two switches so what will
happen as you get everything ready and
then you gotta hit start and it won't
start or it won't score right or
whatever so we'll see but I'm gonna
start working on these little pins a
little bit alright folks so here's what
I ended up with clean clean clean clean
clean clean clean basically using
sandpaper I took off all of the
corrosion anywhere on the board and then
I'm going to nullify it with vinegar so
alkaline is a base and vinegar is an
acid so if you pour vinegar on it it
will stop it from eating but it really
wasn't all that bad so I just cleaned up
all the traces by basically getting rid
of the mask that was on top of the
traces and really there's not much
corrosion at all it was just the mask
was starting to bubble up there was a
little corrosion on these resistors here
so that's kind of a thing I have to keep
looking at now on the back check this
bad boy out
that's what I ended up with which is
pretty damn good it really there are
some holes and some of the pads but that
shouldn't really be a problem if you'll
notice the traces up here are a lot
smaller you know so you don't really
need that whole pad for you know
conductivity and underneath all that
corrosion and where they had soldered
Alma's wires the original pads were
still there Gottlob did a really good
job of making these things really thick
so it looks horrible up close but this
is actually really good came out pretty
nice considering want to start it with
and again we may end up junking this
board that spider chip doesn't work but
at least it won't go to rest with
corrosion all over now these ones that's
just the looks kind of green in the
video but that's that's actually like a
silver color so those are not corroded
that's just the original tinting on it
so when it's copper like that I don't
think it's supposed to be like that
because it'll get oxidized so I think
that's why they put tin on the top and
then over here these were all fine so
that's just we cleaned it up just a
little bit we had two two traces here
this one was broke this one was broke in
half so I put trace tape repair tape on
it and then this one was lifting up a
little bit so you can either glue it
down or I put a piece of tape on it and
so this tape since these connectors are
only one sided
I've swen turnaround and wrapped it
around to the front because there's
nothing that it will touch my connector
now the connectors themselves I these
are strange connectors that only fit on
one side and they have a weird kind of
Keane where the slots are but I actually
have some of those those are old molex
ones so I've got this one and I've got
this one
and I don't have this one side to order
this one and I've got these were fine
you know those are the display ones so
the next thing I'm gonna do is
eventually we want to put a battery on
it and so I need to neutralize this and
then also I'm going to put a ii cap here
a lot of this all of this information
I'm giving you a lot of this you can get
on pin repair.com
clay site he knows all this stuff 50
times better than me I just read over
his stuff and figure out what to do
but he doesn't feel very many videos of
it on board level stuff but um so we're
putting this up just so people can see
what's going on this second cap here
this one right here is part of the reset
circuit basically the board won't boot
if the coin door isn't plugged in which
is one of these I can't remember which
one one of these and since I don't have
this one connector what I'm going to do
is I'm going to defeat the slam switch
which gives you problems a lot of times
anyways by shorting this little
capacitor out putting a wire that
connects to two sides of it and if you
do that basically the board will boot
without these plugged in so I've got
this plug I'm going to get it right but
I don't have this plug yet so I'll do
that I'll do the little short thing and
I'll get some vinegar on this and then
clean it up and get some rubbing alcohol
on it to make it look a lot to clean off
the the vinegar or I'll put vinegar on
it and then I'll rinse it off and then
I'll put a rubbing alcohol on it to get
rid of the water yeah it'll take a
little while but then once I do that
I'll start reeking at least this
connector since I've got the connector
and then all I mean repenting and then
I'm gonna defeat this slam switch with
that little mod and then we'll see if
the thing still works and if it does
then we can move on to this connector
that goes down to the driver board and
start testing the driver board and we'll
talk about that a little bit too okay so
we went ahead and mounted it back in and
we're upend this one connector because I
had a new connector this one we had to
order and we had to order this one so
we're kind of at a standstill on that
what we're going to do next is take the
driver board out and test everything on
it and there's some little updates you
can do to it and
now one of the things that sucks about
this is there are this this driver board
does not have the added protection
diodes on it so there's these little
diodes that usually I think they're up
here in the corner they're just right
next to each other so basically this
this has a problem where one of these
transistors can short and if it does it
sends a weird voltage back through the
lines up into the board and Fries that
spider chip this is one of the ones that
has the ability to do that if it was the
one with the little diodes I think
there's seven diodes or something if
there's if there's one of the ones with
the little diodes and there's no chance
that that could happen everything's cool
so I'm gonna look in our box to see if
we've got one of these that has the
diodes and if we don't I'm going to add
the diodes so you can add them to these
little transistors but pretty much you
have to do that if you don't it'll just
board will get damaged now if you want
if you're messing with one of these you
can get a new power supply you can get a
new cord you can get a new main board
and you can get a new driver board or
any combination thereof now if you get
the new driver board I mean the new
motherboard it doesn't need the driver
board to have those little diodes that
put protection on the on the motherboard
so that it can't get fried like that but
it was a big problem there for a little
while I so you can buy this little
connector harness that goes between
there you can buy that brand new so a
lot of these you can buy new you can't
buy this harness because it plugs into
stuff on the bottom of the playfield so
the next thing we're gonna do is set a
driver board out and start looking at
that and we'll test some things on it
alright folks I pulled out the driver
board and I wanted to show you a couple
little things this is the one that was
in there it's really clean and in really
nice shape so I'm gonna put this one
back in there but before I do that I
have to do a I have to test all of the
transistors and everything and I have to
put a ground model in it might as well
do that while it's out we'll talk more
about the ground here in a minute so
you'll see that whenever I put it back
in but the main thing is the diodes
that's talking about so I've got several
versions of this board here I've got
this one which is the one that was in it
I've got this one which is a really
early one you see it's a different color
right I've got these are the two are the
same so I've got this one I just add
mine around and I've got this one this
is probably the best one that I've got
if you'll notice the difference this is
the one that was in it and this is the
one that came out later the problem they
had was these some of these transistors
can short out and whenever they do it
sends 24 volts back up through the
harness into the mainboard and Fries one
of the Spyder chips which you cannot
replace you can't get new one so after a
while they figured that out and so they
changed it so the easy way to tell it
you can see the bottom right-hand corner
it looks about the same the easy way to
tell it is on the new one you can see
the diodes right here right
so those four diodes are in the line
from these four back up to the board so
what a diode does is it basically makes
it where voltage can only go one way so
voltage can't go back up into the board
and then if you look really close on
these three there's three little diodes
down below it that aren't on this one so
what I'm gonna do is I'm going to add
diodes to these seven which will just
protect that line so that that can't
happen
and then that board will be safe to be
in any of them I could just switch it
out this one here actually looks pretty
clean and somebody's already done the
the I guess that's the I don't know what
that is
that's not the ground mod that's just a
some kind of hack
so I could just put that one in I'm just
gonna go with the one that was
originally in it the things clean it
just needs a little updating so I'm
gonna do that and I'm gonna attach the
ground wire for the ground and then
we'll put it back in I'll test all of
the transistors to make sure they're all
right you can do that with just a diode
test you know like you normally test the
transistor so I'm going to test all of
these little ones which are your lights
these big ones are your coils I don't
know if these are lights or coils and I
don't know what that one's for but in
the manual that tells you what each one
does but I'm gonna test all those I'm
gonna solder on a ground wire which I
think goes over here I'm gonna look it
up to make sure and then I'm gonna add a
diode to each of these seven transistors
here which are the ones that can cause
the problem so I'll be back here in a
second whenever I get that done okay so
this is what we ended up with so we got
in or order with our extra connector
that we needed and we extended the wires
a little bit because they weren't quite
long enough we used we just soldered the
wires together and then use heat shrink
tubing over them so that they wasn't
short out with each other so we got the
new connector on there I made I had the
bottom of of a connector that was fine
but the top had been removed on that
other once I used I had another one that
I had another bottom so I was able to
turn it upside down and use it for that
connector so I made a new harness for
that and then the transistor whenever I
added these diodes like I was talking
about you just add them to the left leg
with the band side up so that it can't
send power back to the board whenever I
did that this particular board with
these really old huge transistors the
pins don't like to bend so once I was
trying to just lift the pin up in the
air and solder the dial one but I broke
one three of them doing that so I
replaced those two you can put a tip 102
in for that which is used on a whole
bunch of other different pinball
machines so I made the new inner board
connector I put the new cabinet switch
connector on there wit course we'd
already repend that one with
new connector so we got rid of all that
trash that was soldered to it whenever I
first saw it I wasn't sure if that was
gonna happen
this is the little jumper block that
they were using for it right and then we
did the ground mods as well so what you
do is basically this is real simple in a
system one it's a little harder on the
later ones but one basically these
machines start having all kinds of
problems where they'd lock up and
there's a negative 12 volts that comes
off the power supply if you lose that
these spider chips start freaking out
and it makes a lot of the coils and
stuff pop one on the playfield tour
they're stuck on which causes all kinds
of problems and issues screws up the
driver board and if that doesn't have
those diodes can screw up the main board
and on ba bla bla bla bla bla bla bla so
they eventually a couple gentlemen who
were really into these things
I believe his name's John Robertson he
figured out that the reason that this
was happening was because the ground
wasn't any good on the board so the way
they Gottlob did these grounds was this
power supply has a ground and it sends
it through that black wire to the main
board which grounds the main board which
then sends it through this connector
down into the driver board which grounds
the driver board but the problem is is
that if you get any kind of resistance
in any of these lines you lose your
ground on the board and then you have
all kinds of problems go on so the this
board may have a different level that
the ground is that voltage wise then
this board does so the way you fix that
real simply is you just tie all three of
them together to the back box so you can
see that I've added I need to tighten
that one don't I that ain't good you
I've added a ground wire from the ground
which is right here
over and tied it to the back box this is
metal in the back right and this is how
most pinball machines are done the
modern ones that in the 80s that's how
they did most of them but Gottlob didn't
Gottlob was horrible but grounds and
then i've added another ground over here
on the driver board on the bottom of
this little cap here the hood ground
side and then added it and then i
grounded it to that piece of
and then on the power supply itself I've
added a ground to the main capacitor and
just grounded it to its frame because
the frames well grounded over here with
these screws holding it to the thing so
basically that ties all of the ground
points together and makes the game not
lock up so there you go you have to do
that on a system one or you will have
trouble so I tested all of the
transistors on the driver board and they
were all fun even the light ones we'd
already tested the power supply and then
after getting all the switches and
everything you know all of the switch
wiring straightened out where it's not a
rat's nest in there anymore you probably
saw I don't think I've showed you
earlier that uh there was some weird
stuff going on on the displays but that
was just because the battery was dead I
had taken the battery off the board so
once I added this little battery pack a
little remote battery pack I was able to
go into the audits and reset all of the
audits so now we've got all of our zeros
like we should this one digit was
missing on this display but it was just
because the connector was dirty very
simple right
so we'll try it out now Gottlob has a
really bad test system so basically
inside the pointer where you have this
big button whenever you hit it you go
into test mode all right
so I guess I'm in test mode setting one
setting to setting three if you go all
the way to 13 you'll get to see so that
one is the one to test the displays that
one test the right display so here's
test 13 finally we see all the lights
come up like there's now test all the
solenoids that's it that's all the
solenoids that are in this thing and if
you hit a switch on the back it will
show you like what's which it is I
believe yeah 20 so it's this like the
worst switch test over but it does work
and then if you don't hit a switch for
five seconds it goes back out into the
game so it's a really bad test but you
can't you saw how long the lights roared
they were on like five seconds so you
have to yet you have to go into that
test mode and then real quick look and
see if any lights are burnt out and then
it'll test the solenoids real quick
it won't test them twice and then you
have to you can you can test switches
but if you don't hit a switch for a
couple seconds the air back out of test
mode so the test mode on this thing was
horrible but there you go
up and running with the original boards
how cool is that folks so I'm going to
film another video of this showing just
kind of the game design a little bit and
the rule set and how to play it and
we'll see you on that video subscribe to
us here if you'd like videos like this
we kind of just wanted to do this one to
show how a system one board set works
and how to work on one I'm subscribed to
the subscribe to us if you'd like to see
more videos like this and make sure to
give us a thumbs up even if you hated
the video even if you hated the video
give us a thumbs up because that helps
us out
it lets other people know about our
video and YouTube promotes us and things
like that and it really helps us out so
we would appreciate that for us taking
the time to make the video and leave
your
comments below if you have any opinion
on the system ones or the system one
board sets or have you do you have any
experience with the knife replacement
boards or the there was one the pass
call board set that's an all-in-one
board set if you have any opinion about
any of that stuff or you want to talk
Gottlob system one leave your comments
below and we try to respond to all of
them so I hope you enjoyed the video
make sure to subscribe to us and we'll
see you on the next one