Thank you to everyone who has been supporting our channel! If you use the link below before you purchase anything on Amazon, we get a royalty for sending you there, thank you!
Our store is located at 139 Caldwell St., Rock Hill, SC 29730.
ladies and gentlemen this is Joe's
classic video games back with another
cool
pinball repair video for you today we
have been working on this Bally lost
world that most people would have
thought was a lost cause but we've been
slowly fixing it up and filming videos
of it the first video we worked on the
power supply the rectifier board and the
transformer and we stripped down the
play field and then the second video we
repainted the play field and repopulated
it got it looking decent it's nice and
presentable now play field wise but the
game doesn't have any of the board's up
and running or anything in it so today
we are going to be working on getting
the board sets working so let's look in
the back box I'm gonna go through them
kind of quick because I want to get them
all done on one video what do you think
about that so this is the rectifier
board which we worked on last time if
you go back and watch the first video
you'll see that so next it sends the
power up to the solenoid driver board so
we're gonna pull that out and work on it
next so I'll pull it out and put it on
the bench and show you what we do to
them and then run through it real quick
after that we're going to work on the
mpu this is the lamp driver board and
then we need a set of five displays over
that might be the tough part so I'll
pull up solenoid driver board and let's
see what we can do there so here is our
solenoid board this one looks very nice
it's very clean it's in very good shape
so we're gonna replace the filter
capacitor we're gonna reflow all of the
connectors I'm going to use my
multimeter to check all of the
transistors down here make sure none of
them are burnt up which would cause a
coil to lock on or that are open which
would cause the coil not to work and
then every we'll do a couple little
ground upgrades we got all of our
information about the upgrades and stuff
to do from pin repair.com clays guide
that's been out there for years and
years and years about how to do it to it
so we'll get started on this one and
this board basically takes the 12 volts
from the rectifier board and it turns it
into 5 volts which it uses to which all
the other boards used to run
and then it also of course these chips
use the five volts and run as well and
then the it also takes in the display
voltage and and turns it into basically
a lower voltage of a regulated voltage
in this area that it sends out to run
the displays now I believe we're
probably gonna end up putting LED
displays in this so we won't need this
part but I'm gonna fix it and check it
to make sure it works anyways just in
case somebody wants to put the original
displays in it down the road so I'll
work through it and we'll see what it
looks like so two upgrades we always do
in the back as this is the ground for
the filter cap instead of it just going
out this one pin over here we tie it to
the the rest of the grounds right you
can just put a little jumper to that
trace under and then this one up here
this big cap is the display the filter
cap and so we tie the ground on it to
the main grounds as well it's the same
deal basically and then we we tie test
point one that bottom in there to test
point three and the reason you do that
is because there's this weird little
design thing where it sends the five
volts out one of the pins and then
through a little pigtail back into
another pin to run these chips so this
creates the five volts but it doesn't
send it directly to these it sends it
off the board through a wire back onto
the board and in it so whenever you tie
those two together you make it where
it's sending it directly to those just
basically whenever the power goes off
the board you have the potential for it
to lose have resistance and cause a
problem and then of course to put a new
filter capacitor when reflow to all the
connectors and that's about all we got
to do how we tested all of the
transistors everything was fine this one
and also the ones in the high voltage
display you could replace this sometimes
those are a little iffy little iffy they
get a little spot anymore they don't
work
right but I honestly I don't think we're
gonna use any of this high voltage stuff
but that one test fine so but if you're
doing this for one that you're leaving
us blazin you might want to replace that
pot if you've got a that old one still
on your board so this one is ready to be
tested back in the games we'll pop it
back in there and see if we're getting
our test voltages right okay so we put
it back in the machine we turned it back
on now remember so I just took the MPU
board out but it wasn't plugged up we've
also got the power disconnected from the
lamp board and the reason that you do
that is in case this thing isn't making
five volts it's making 12 volts or
something like that if it sends 12 volts
over to the IC chips on the other boards
it'll fry them so the sound board is
unplug the light boards unplug the
displays are unplugged and the MP use
unplug so we're going to test it first
this top test point is the voltage
coming in so it's cut fourteen point
seven s coming in and then this
regulator here is making five point
three nice and stiff like we like it and
then test point three we have tied to it
same thing and then over here the
voltage for the display is coming in is
250 something and going out is 176 yeah
the board is making all the voltages the
proper way so the next thing that we
have to do is work on that freakin MPU
board so we're gonna go check it out and
see what we can figure out okay folks
this is the NP you out of it and it's in
pretty rough shape but it's in better
shape then that one we did recently on
the Stingray I don't know if I've
uploaded that video for y'all by the
time this video comes out but yeah it's
kind of rough but this one is in like I
said in better shape than the other one
the problem is though it so this is the
early valley board and the problem is
the sockets
suck on these things I don't know about
those brown ones I mean they don't look
that great to me but these ones here
that say all gat these are known for
sucking horrible sockets it has
something to do with the way it holds
the pins it just isn't all that great so
if you got those usually you have to
replace them and the reason that you
have to replace them is because they're
they have intermittent problems so you
you know the leg will be making a like
electrical connectivity for a little
while and then it decides that it isn't
and so your board stops working and then
you have to figure out what the problem
is it's just they're not they're just
not reliable so we're probably gonna
have to replace all three of these
sockets which is why these early ones so
working on somebody's replaced this
socket to of course all this needs to be
redone but so I could just buy a new
board but they're about two hundred
bucks
and I've already spent 250 for a back
glass a little over a hundred for
displays and then all the time and stuff
that I'm putting into it so I could
spend another 200 on the back glass but
then we're getting up there a little bit
on what we're in the machine you know so
we really need to make a pretty good
profit on it to cover the time which
means that we are going to end up
putting even more time into fixing this
board right so I got to clean all this
corrosion off this is from of course the
battery leaking I got to clean all this
alkaline damage off get it as shiny as
possible and then replace all of these
parts around the bottom that are screwed
up and it looks really rough but it's
not quite like I said it's not as bad as
the last one I did so it's not it's not
all that bad it's not even up to this u7
which is where the
6810 ram goes and it looks like it
didn't get up to this socket even though
I want to replace it anyway so you've
you know the bottom inch and a half
there is messed up and then on the back
it's pretty much just the outside trace
there at the bottom and then just a
couple traces here going to the rim so
it's it's not that crazy
so the first thing I'm gonna do what
starts I'm gonna start sanding some of
this corrosion off I'm gonna use a file
on it and then I'm gonna use sandpaper
and then I'm also going to start taking
these components off that will be
replaced
this socket needs to go and trying to
clean it up a little bit and then we'll
we'll see if we can get it to where it's
where it's a good starting point to
rebuild and put a board together
there's the CPU is missing both of the
PIAA s are missing both of the roms are
missing which is fine the 6810 Ram is
missing in the 5101 Ram is missing so it
needs a little help
so I'll start taking stuff off and let's
see what kind of shape we can get it
into so this is what we got after the
first good scraping got a lot of the the
loose surface grime off the back looks a
lot better than the front so all the
loose stuff is off so now I'm gonna
start taking each component off at the
bottom a little bit and then once we get
it down to where it's just the traces
and things I can actually sand it and
get it even get it even cleaner get rid
of this green and stuff hopefully so
I'll start taking all that stuff off
okay so I got it nice and shiny I think
I got all of this all of the badness off
cleaned it up
clean clean clean clean clean clean the
hardest part is sometimes whenever you
take the pieces off the legs break off
and stuff and then they're stuck in the
hole so you have to get that as clean as
possible
this one since it wasn't as bad as able
to get it a lot cleaner than I was able
to get the last two that I worked on
damaged down here where it's broken
we'll probably still have put a couple
jumpers on it you can put wires and
stuff but I like just using cap legs and
stuff and then so I'm going to put
vinegar on it with a toothbrush and then
I'm gonna put rubbing alcohol on it I'm
gonna want to rinse off the vinegar then
I'm gonna put rubbing alcohol on it to
make the water evaporate a little bit
quicker and we'll see what it looks like
after it's all nice and shiny and then
I'll just start putting the stuff back
and I'm probably still gonna have to
replace these three sockets at least and
maybe these as well
all right folks is how it looked cleaned
up very nice almost has a marbleized
look soon it'll be an oxidized look so
just like I've done on the other ones
have you ever seen it if you go to Great
Plains electronics calm he used to sell
these little kids of all the stuff you
need to fix them and he's out of the
kids but he still has the paperwork
online and I don't believe he managed
this using it so basically this tells
everything and it tells you everything
that needs to be replaced and he's got
this handy little map of the board all
this is in your schematics too but his
little instructions make it very easy
Thank You ed we appreciate it and
depending on when you see this video go
check on Great Plains electronics iffy
see if he has any of these kits back in
stock I don't know if he plans on making
any more if you can't get them there you
can get them at Big Daddy is a big Daddy
electronics I think is the name of it
the pinball guy also does pinball stuff
he has kids too so they're real cheap
they're like $10 $15 something like that
but it's all the stuff to replace all
the stuff on the bottom of the board
that gets damaged by the alkaline
corrosion so we're gonna start putting
stuff back as detailed on the thing go
through there I'm gonna do it all pretty
quick because I trying to get all of the
board videos on
on video so I'm go ahead and repopulate
all that stuff and we'll see what it
looks like after that all right here's
what we ended up with I keep having to
put these these were point one you left
oh I'm sorry
point 1 micro farad capacitors I need to
order some smaller these are like two
thousand volts and you only need 50 volt
but we're getting them in there right so
we've got everything repopulated now
whenever you do these you really need
here's where you're gonna have the
problems these traces that go down and
then go through the board through with
the via you know so these four here and
these two here and then over here
there's a couple right down here and so
those are really easy for that to get
all corroded and eight up to where it no
longer connects through both sides of
the board and so once it does that you
uh you lose that address line or
whatever it is going to this Ram chip
and so you'll get you'll usually get I
think the I think this one's messed up
you only get two blinks so but yeah we
got that then on the back on this one
none of those traces were messed up so
that was good got everything back in
looking pretty good so now the next
thing that I'm going to do I'm going to
start swapping sockets so I can get it a
little more reliable and then we're
ready to test it out and once I get all
the chips repopulated on it alright
folks I replaced the three sockets I put
in three this is a 6800 these are sixty
eight twenty ones with I've got a bunch
of those over the years I've had a bunch
of these mpu boards that had two acid
damage and stuff so these are chips that
I had laying around off of some of those
this is a 68 10 this is a 50 101 which
is the this is the RAM and this is the
memory that holds the the high scores I
haven't put a battery
yeah the the to rob chips that go here
are game specific of course that's what
makes it a lost world instead of a night
rider or whatever so I need to burn
those I look I actually have a bunch of
those old proms that go in there
they're not super reliable if you can
upgrade them it's probably a good idea
but I don't even I don't have the old
ones so I need to burn some for whatever
reason this board was in the cabinet
with with all the chips missing somebody
had scavenged all the chips because they
thought we wouldn't be able to fix this
board I see what they did they had
abandoned this baby all right so we're
going to burn two new roms and then I
have to change the straps so there's
these little and I'm you've probably
seen this before
I've been over and let other boards
there's these little jumpers so efore is
connected to III right now but it's not
connected to II thought with a little
jumper over here ye seventy-six are
connected down here you want any two are
connected sometimes one of these may not
be you know just depends on how it's set
up and what that does is it sends power
and address lines to different pins on
the this row of sockets here so it it's
how you can tell it what type of socket
I mean what type of chip is in the
socket so it could be a 27 32 27 16 25
32 it made you 25 16 I don't know where
the original proms so those jumpers or
things that it needs to tell that I said
27 32 but I don't think it will actually
work with those with just the jumpers
you have to do some modifications so we
might have to do that to this so I'm
gonna go check that all out again I'm
getting them almost all of this
information from pin repair.com clay
site he does a great job on these and
those all about it and so I always refer
back to that and I've done that over the
years any time that they any time that
we're working on a NP you I always check
his out I think you can go to pin wiki
comm as well I don't know how
in depth theirs is yet but they were
meaning to make that them the place to
go for pinball information so but I'm
going to do some reading and see what
kind of files I need for here and what
what kind of chip I need to burn them on
and then what kind of jumpers I need to
set I was going to think about replacing
these brown sockets too but they
actually look pretty decent it's a
double wipe socket so that's actually a
decent looking socket I'm not so sure
that that means changed so I'm gonna try
it I'm gonna wing it now these I did go
ahead and change because then things are
horrible just the way they work isn't
all that great so we're gonna leave the
brown ones for now unless they don't
work and we're going to we swap those
three
I hate swapping a bunch without the
board being tested because if I screwed
up one of those pins
4080 a hundred and twenty twenty two
hundred and forty two pins I've changed
on this thing if one of those isn't
right it won't work you know so I hate
doing them all at once it'd be better if
you could do just this socket and then
try it back out and see if it's up and
running then you'd know if it doesn't
then you know you screwed something up
on the socket you not know where to look
but if it's screwed up now I know I'm
not gonna know where to look I'm not to
just look at everything but I'll go
research those wrongs okay so we're on
pin repair.com this is the mod that
we're doing we're trying to make it
where it will take a 2732 EEPROM at you
two and at you six because the old ones
were those mast roms that we don't have
and we don't have the ability to burn
and so a slightly more modern but not
crazy more modern was a twenty seven
thirty two now looking it all up it
looks like u 1 u 2 and u 6 originally
had problems in them so those are gone
and we're going to put a prom a 27 32 in
u 2 & u 6 which will make it a lost
world so you
to do all these little hacks basically
little jumpers and stuff so I did that
so let me show you what I'll show you
what I did so here is our board I was
looking on pin repair.com like I was
saying and he's saying these brown
sockets are horrible but he was showing
these which he was calling calling a
closed socket that little top piece
comes off and it turns it into what
these are so I don't know these look
like good sockets to me but we'll find
out they made they may that may be
horrible it might be the most horrible
thing ever okay so I put the Bernoulli
prongs I made that I had to change this
jumper and then there was a bunch of
little stuff I had to do I had to cut a
little trace there I had to cut a little
trace there and then on the back on the
one socket I had to cut two traces and
our one trace and put a jumper wire and
then jumper the that socket up here to
the CPU and then I also had to run a
line down so that it grabbed the same
pin on this one and I had to put a
jumper on this one and cut a trace so
fairly some minor little hacks and then
there was a couple little hacks over
here I had to cut two traces and join
them together but hey I think we're good
I also put a battery on it I'm trying
these now little button batteries
because I think it'll be easier for
people to replace those and I don't leak
you can put a remote battery holder on
it too and I think you can put you might
be able to put a NVRAM solution on
volatile Ram that doesn't need a battery
but I haven't done that yet maybe on the
next one what do you think about that
maybe on the next one we'll do that
okay so everything looks good but I
haven't even tested it yet and I don't
know if any of these chips are good so
we're gonna put it in the game and try
to turn it on and see if we get any kind
of results all right so we've got to
mount it up in there so I just plugged
in the power and I've got the two power
connectors over here
so basically we're watching this little
LED
at the bottom and we want to get a
flicker and then seven flashes now that
I know that sounds a lot like eight
flashes but it's not the flicker is just
basically like a reset thing and then
after the flicker you get a nice seven
flashes right so let's turn it on so the
flash is depending on how many you get
it tells you what's wrong with the board
so let's see what we got flicker one two
three four five six seven all right so
basically it seems to be working not bad
people what do you think
okay so I'll plug everything else in and
we'll see if we get any any of the
lights working or anything because the
whiteboard would be the next board that
we have to work on okay so I didn't plug
the sound board in because usually those
just make a bunch of noise until you get
them working and so whenever you turn it
on the whiteboard the only four lights
it's lighting up where are the 1 2 3 & 4
on the bonus ladder it doesn't light up
any of the controlled lights on the back
box so I think something is definitely
going on with that light that lamp board
so I'm gonna pull it out and we'll take
a look at it I don't know if it's just
bad solder or if it's what the deal is I
don't have a display yet either so I
can't tell if the displays are work on
Earth it could be that the games coming
up and crashing or something
[Music]
comes up to 4 and then just stops it
stays like that but it does it
immediately so and if I hit the test
switch nothing changes I don't know if
we're in tests or if we're running or if
we're not running or what's going on so
next thing I'm going to do is I'm gonna
go get a display I think and plug it in
and see if we can get something on the
on the display that I hope it's
understand if we're even up and running
all right folks I figured it out so
whenever I was redoing and I broke the
capacitor C 16 which has to do with some
of the timing and stuff this is a 555
timer and I had replaced some of these
with these point 0 1 micro farad
capacitors and I mistakenly thought that
was the same one but it's not that's a
point 1 micro farad capacitor so I
swapped it to their correct capacitor
and the game boots up now so it's it's
running this thing about half the light
bulbs I think are burn out because we
haven't replace them on the play field
yet and I put in a just a parts display
that's got a bunch of burn in it but it
is actually up and displaying the game
is working we got the lights blinking on
and off that are supposed to so we're
getting there now I'm not we're going to
make our we're gonna make some displays
so I'm just using that one as a test one
but the next thing that we need to do is
work all the light bulbs so I'm going to
replace all the light bulbs on the
bottom of the playfield and then we'll
see if we can get in to test and test
them all yes we're in test there and not
very many am i working on the front here
I've replaced all of these the only one
that's not working is the one player
down here that socket feels a little
weird it's probably just a bad bulb or
something but uh so the lamps are next
so I'll start replacing them under the
playfield ok guys and girls we're on the
downward slope here I I mean towards the
the beautiful finish line so I've
replaced all the light bulbs in the
entire machine and all of them were
working
except two and so I looked on the
schematics and it was q7 and Q 53 and
testing q7 and Q 53 both of these
suckers were bad both of them look at it
crap look at that crap you can't even
get stuff to last past 40 years anymore
so I replaced them with two that I've
got off of this parts board that you may
recognize from our stingray that we were
just messing with you
save that five cents so I put them in
they test fine and so that's pretty good
really I mean every every bulb worked
but two of them and one of them it was
because the the the tab was bent over
and grounding itself out so it probably
fried the transistor or something so I'm
gonna put this back in and we'll see how
it looks and then we're we're about
ready to mess with the sound board look
how beautiful it's getting look at this
I'm gonna roll up lights up at the top
man it's starting to get amazing all the
ones on the front that one I was talking
about over there was just because we
hadn't changed the bulb yet all right so
it was in pretty good shape I restarted
the connectors and replace those two
transistors no problems so now we're
down with the sound board so what I'm
gonna do first is I'm just going to plug
in the sound board and see what that
does of course with the power off the
speaker and the bottom looked pretty bad
to me so I think the speaker has issues
but we'll see we'll see if we can get a
peep out of this thing okay so I've got
the eye man
sound test right now it should be it
should be sounding
[Music]
it's not sounding now you want to be
careful when you're doing crap like this
that's bad don't touch that it won't
kill you but it will shock the hell out
of you right but on the on the amp if
you rub the amp if the amp is working
you'll get sound so you'll hear like a
hum something like that I'm getting
nothing which i think is probably
because these speakers messed up so I'll
show you how we can check it these are
the schematics of the sound board and
there's a little 2 pin connector pin
number 1 and pin number 2 go out to an 8
ohm speaker that's the speaker in the
bottom so you can take your multimeter
and that little plug with the 2 pins you
can just check resistance from here to
here and you'll get the resistance which
isn't the same as the impedance it's not
the same thing but you can measure the
resistance and if it's anything near
thee if it's anything near 8 ohms you're
good but it's probably going to be
infinite because the wire has broke off
the cone or the speaker coils went bad
or something but if it does that like on
this particular one there's holes in the
speaker cone so I know it's bad right
but sometimes they'll still work if
they're like that but that's how you can
tell if yours is any good just check the
resistance across the terminals and see
if it's anywhere near what the ohms are
supposed to be it's not quite the same
thing which you'll notice if you read
the comments below so this is what was
in it
mm so we put a new cheapo speaker in it
you want to try to match the impotence
if you can't so you want to try to put
an 8 ohm in there if you put a different
ohm impedance in there it'll be slightly
off and the amp might not like that
so dopher an 8 ohm er if that's what it
had in there originally okay so I'm
gonna turn it back on and see if we get
a peep out of it now okay folks I'm
gonna let you see and hear what dr.
frank enstein must have seen and heard
back in the day all right so that's
obviously the sound board test now on
these there is this knob that you can
turn to change the pitch that's the
sustain I guess
[Music]
so all the way down let's go all the way
the other way this is going to be
horrible but people
[Music]
so you kind of got to get in between
[Music]
some of them though that's that's called
the sustain adjustments some of them
have a pitch adjust okay all right so
we're gonna go through the test I'll
show you where we're at I can't see the
test number because we don't have the
ball and play display in yet okay it's
going to boot up very cool
okay so I'll show you the different test
modes real quick so what was the first
thing we fixed remember we did the power
supply and then we did the we did the
the rectifier board I still need to put
a pin ball over there we did the
transformer and the rectifier board and
then we did the power supply and the
solenoid board which creates the five
volts which is what is running the CPU
which is running that's how all of the
lights are twinkling and doing their
thing and moving and animating and then
so we got the CPU up and running and
then we were testing to see if the
displays work right and if the lamps
work so there's the lamp test all of the
bulbs are working and then the next one
is the display test we only have that
one display our next video is that we're
going to be making brand new displays
for for Bally games also Stern game
six-digit ballet and stern displays and
we're going to put them together out of
a kit won't that be fun we already did
one of those for Williams games it was
pretty cool but this games get an
all-new display so just what the display
in it is working which means that the
mpu which sends a signal to the display
is working or at least enough to do the
first player one and so then after that
I also worked under the play field and
so we're going to test all the solenoids
that's the next test so they're all
working and this is the sound test it's
working
unknown caller okay so now we're in some
of the settings which you can't tell
because the right this is probably the
switch test actually but it displays on
the ball and display now this is the
first high score so if you put it on
10,000 it makes it where you win a free
game every time you know every time you
score 10,000 points you win a free game
so that's one way people put it on free
play when I burnt those roms earlier I
burnt free plently roms for it though so
its own free play by the dip switches
but the first replays should be two
hundred ten thousand points oh right
second replay should be four hundred
thirty thousand points
to do all right
third replay level we're not gonna set
and these are like all the how many
coins I've been in it and all this stuff
which is all zeroed out because we
haven't actually played any games yet
and then if you get this about setting
11 or something it resets he goes back
in the gameplay all right so we have got
all the boards working we even have one
of the displays working even though it's
all burnt you probably can't tell on the
camera this is what happens when you run
it at too high of a voltage for too long
it scorches especially those two there
because they light out more often
so it it shows the high score by the way
that little light there is normal that's
the filament voltage it's just always
there but the half the time it shows the
high score and then half the time it
shows double zeroes so those two zeroes
get burnt man they get burnt so it's
just an old display with an old glass
it's actually still working but it needs
a it needs a new glass a new glass is
like 60 bucks a piece now because
they're all new old stock I don't even
think they make them new anymore
well they make this cool little kit it's
like one hundred fifteen hundred twenty
dollars and we're going to put it in now
but I think we're up and running I guess
I could try to coin it up that's what it
sounds like when it comes up do I have a
pinball can a brother get a pinball my
brother got a pinball let's see if it'll
start is there anything more satisfying
than the damn ball going from there to
there yeah one of the greatest things in
the pinball world right they tweeting
the correct date they're texting the
crap out of them they must have heard me
so we're on 0 let's see if any of this
thing of scores
well failure to launch that'll do it
it's about like when I'm actually
playing got eleven hundred points I'm
yeah giving him points beat up the banks
forty five thirty
all right folks looks like we've got her
up and running and like I said we're on
the downhill slope I'm sure let's love
the sound of that ball rolling her home
that's would people what still have all
my fingers I thought it bit me so why
did it go down back it's because I set
the world record so if you set the world
record on this game you get three free
games so get that dad was me getting
winning three credits because look at
this that's right I'm a scored six
thousand three hundred forty points beat
that suckers beat that alright so there
you go so I think I will do it for this
video will shoot another one tomorrow
though of us doing the displays and then
we're gonna run these all one week then
we're gonna fix the game all in one week
and it's gonna be video after video week
all week long and then we're going to go
out of here oh we're going to bring this
thing from zero to hero what do you
think I think we're about 75% of the way
there but leave your comments down below
let us know what you think so far is it
exciting to see it come back this for do
you enjoy seeing us save these old games
now remember what this thing looked like
people now you remember when we brought
it in it was laying in the floor like a
pile of trash right no back glass still
doesn't have event glass no displays
still doesn't have any displays Oh
alkaline damaged MPU and it would know
roms or anything in it
brought that back that was pretty
phenomenal everything screwed up and now
we've got it up where you can actually
play a game so much so that people are
violently furiously texting me for the
opportunity to come over and play this
thing right believe your comments below
let us know what you think so far if
you're enjoying the series or not let us
know where you're from we've been trying
to shop people out we keep having people
let us know where they're from
we had a gentleman just the other day
tell us now by the way whenever I film
these videos I'm Way ahead of y'all I'm
months ahead so if you're watching this
video I probably filmed it two months
ago because that's how we roll just in
case whenever this virus thing popped
off didn't bother me I had like 15
videos already filmed I just uploaded
the stuff I'd already filmed right but
uh didn't bother me in that way it
bothered me in other ways of course but
you know what I mean we're prepared
people were properly prepared so we had
a gentleman the other day which was
probably a couple months ago by the time
this comes out tell us that he was from
West Virginia and I am I was born in
kunal City West Virginia and grew up as
a kid and the west side of Charleston
West Virginia so shout out to him we see
you up there
we had another gentleman from Hickory
want us to mention him we see you over
there in Hickory that was me playing
with the pedal under the game so let us
know where you from and we'll we'll try
to give you a shout out if we remember
if we don't remember just keep
mentioning it right and to the guy that
kept wanting us to show them how the
Tilt works
we saw you saying all that to we the
stingray video I don't know if it's up I
think I already uploaded those that's it
again I don't know because I've already
filmed it but I haven't uploaded them
yet but by the time this comes out the
stingray video ought to be out we showed
it in detail on that so check out the
stingray video if you're still wondering
how the Tilt works but uh leave your
comments below we have an amazon link
down below if you click on that Amazon
link you don't have to buy anything in
particular or sign up for anything but
if you find yourself wanting to buy
something on Amazon if you simply click
our link before you do that
and just do it the way you normally do
sign into your account or whatever but
click our link first it tells Amazon hey
these people were sent there by Joe's
videogames Lyons arcade let's give them
some of our profit so they don't raise
your prices or anything but they send us
a piece of amazon's money and I love
nothing more than spending Jeff Bezos
money ah man it's awesome I can't
believe he lets us do it but yet he does
and he's a man of his word he seems to
pay us every time somebody does that so
we it's very very refreshing so we've
had people on there buying all kinds of
cool stuff
we had a gentleman earlier buy an Acer
laptop we appreciate that whoever did
that very cool but you don't have to buy
anything expensive people have been
buying just little things we actually
did have some people buy some face masks
that's cool everything's cool it's all
copacetic people they pay it's like a
percentage of anything anybody buys and
it doesn't have to be something that we
suggested and I don't believe if it's
something that we did suggest like we've
put up some links to some of our tools
that we use and things like that I don't
believe they pay us anymore for that and
I think it's it's all different for
everything but I think it averages out
to three or four percent of an item
that's very cool people we appreciate it
everybody that's been doing that thank
you thank you thank you we see out there
and we appreciate you thinking of us we
also have which you may have seen a
second channel now and it has nothing to
do with arcade games or pinball machines
so if that's all you're interested in
you will be sorely disappointed by our
other channel it's mainly about my
brother Donnie and it's called the name
of the channel is very creative are you
ready for this it's called my brother
Donnie so if you go find that usually we
put a link down below the videos me and
him him and I are working on rehabbing
this old mobile home that we bought
right now and the thing is completely
destroyed just about as bad as this
pinball was when we started with it so
go over there and check it out I'm over
there a little bit on his channel and he
gets into all kinds of crazy stuff he
does a lot of like small engine repair
and hillbilly hacks things like that so
if you like hillbilly hacks you'll love
his channel he's really good at it leave
your comments below give us a thumbs up
for taking the trouble to film before
you I always have a rag with me there's
still some dust around on this people
leave you comments below let us know
what you think and we will see you on
the next video which hey will be
tomorrow see you then