Thank you to everyone who has been supporting our channel! If you use the link below before you purchase anything on Amazon, we get a royalty for sending you there, thank you!
Our store is located at 139 Caldwell St., Rock Hill, SC 29730.
Ladies and gentlemen, this is Joe's Classic Video Games back with another cool
jukebox repair video for you today. We have been working on this Rock-Ola 490 jukebox and
it's the Super Sound 2. So this is the 490-2 I believe. We've done a bunch of videos on these
in the past and people seem to enjoy them because there's not a ton of information out there about
this particular model box and it kind of gets a bad rep because it had this control unit in it,
the System 2 control unit. It was only used in I think the 490, the 494, something like that,
just a couple boxes. And then by the time they got to the 498 or something like that,
they moved on to another control unit. But they sold a ton of these things and a lot of
them are broken. So I wanted to show you a little issue that's going on with this one and we're
going to attempt to repair it. We get a lot of people emailing us and asking us questions about
these and calling us because they've got one they're trying to work on. So I'm going to show
you kind of what one's doing and what we think might be the problem and what you can look at
on yours and how you might get it working. So this particular one, when I plug it in,
you get an idea of what to look for and what's going on. If I try to scan it,
I don't get any kind of scan action. I do get the turntable moving, which is something that
tells you something. OK, we're going to slide this back to off. OK, and if I go to operate,
it's trying, it should be trying to go back to home position and it's not. The turntable's
barely trying to move. There's some stuff going on, right? So let me show you what to do if you
end up with one in a similar situation. OK, the first thing you want to check is to see if all of
your LEDs are on on the power supply. So if you've got an earlier model of the 490, it will have a
slightly different power supply. This particular one is the 54920-A. And the reason that it's in
this one is because, like I said, it's the 490-2. So there is a 490, a Rockola 490-1,
and a Rockola 490-2. They sold so many of them that they redesigned the entire power supply
kind of right in the middle of the run. OK, so this one is the one that's in the later models.
So you want to see, but if you've got the earlier one, I believe it has a more of a
horizontal thing up here. This is the amplifier. But it has a power distribution center that has a
little board on it with the LEDs on it. So you want to make sure all the LEDs are on.
If one of them is off, that's probably your issue. Now if one of them is off, it's possible that it
actually works and the LED is just burnt out. But that's, you know, I'm just giving you a place to
look. If you search the internet for the schematics for a Rockola 490, they are out there. You can
download them for free. If it's the 490-1 or the 490-2, like this one. If it's the original 490,
I can't find those schematics. So if somebody has some, scan them and mail them to me.
But there is the Rockola 484 schematics, which is from a year or two before this,
that has that older style power supply in it. Those schematics are floating around. So depending
on which one you've got, you need to kind of look and see if it lines up, right? So you're going to
have to get your hands dirty a little bit to work on these though. OK, so you want to see if all of
those power lights are on. However, there are a couple more voltages that come out of this thing
that they don't have an LED for. So it could be that these four are working, but you have a couple
more that are missing. I'll show you that on the schematics here in a minute. So you want to see
if that's working. You want to look at your board up here. Without that working, your
system 2 control unit working, the turntable and all of this will never scan.
OK, so let me, I can't put this on right now because of our battery setup. Basically we're
not going to deal with this in this video because this system here is actually working. We're going
to deal with the power supply and the mech board. OK, but basically if you look up at the top,
it tells you what those lights mean. The left light means standard pricing, special bonus
pricing, lock-in pricing, default pricing, and then there's one that says normal operation.
OK, now when I turn this thing on, if I can get focus back, I'm going to turn it off and back on
and watch what the light does. I'm going to try to, without knocking the power brick out of the
machine. Alright, we're just watching the light people. See the one at the bottom right?
And then see how it went off? OK, let me get my focus right. So when you first apply power to it,
it's saying initializing, lock-in, that light is on, and this light is on over here where it
says standard pricing. OK, and so those stay on and then after a few seconds they both turn off
and on ours, this one comes on where it says default pricing. Yours may come over to normal
operation. The reason that ours doesn't go to normal operation is because we don't have a
battery installed. So we haven't saved the pricing in it to the point where it can move over to that.
But by the act of it turning this light off, turning that light off, and then turning that
light on, what that tells you is that the board is actually working. It may not be working fully,
but it's at least running the code and it's booting up. So if yours isn't doing that and
this light is staying on or that light is staying on, you've got a problem with your control unit.
If you've got a problem with your control unit, you might be in trouble because
you're going to have to fix it yourself basically. There's nobody around that repairs them that I'm
aware of. There may be somebody, but not that I'm aware of. Luckily all of the chips on that
board are socketed. There's a front board and a back board. If you've got a couple of them,
you might be able to swap the boards around and see. You could order a new chip for every board,
every chip if you wanted. You have to deal with that. But we're not going to get into that too
much in this video because I actually have a working one in there. I also have a working power
supply. But as you can see with the working board and the working power supply, I can't get the
basket to turn. We're stuck on a record. We're at record 190 or something like that.
So what's going on? I get people emailing me about this constantly. Constantly. OK,
let me show you the first thing that you need to check.
Alright, there are two motors that do two different things, or three motors actually,
on this setup, right? Now Rockola's setup didn't change much over the years. It's very similar
no matter which Rockola you have. But this is specifically for a Rockola 490 or a 494.
This is the cam, OK? So this unit spins whenever this is improper,
whenever it's working properly. Alright, so there is a switch, or four switches here,
that change state depending on where this cam is, right? And when this cam turns, it turns the
gears and makes the arm move and all that crap, right? Makes the gripper arm function. Alright,
it can only be in one of two states. It can be where the mechanism board is trying to control
the gripper arm, which is in charge of grabbing a record, spinning it around and laying it on
the turntable, and then picking the record back up, spinning it around and laying it back in the
basket. It can do that, or it can move the basket, right? It can't do both because if it could,
you'd break all the records. So let's say that it's coming down and the record, and then the
basket starts moving. Well, it would break the record, right? Or it would put it in the wrong
spot because the basket moved while it had the record here. So basically, there is a motor that
turns the basket around to the correct spot. Once it gets to the correct spot, it stops,
and then, and only then, it allows the gripper arm to grab the record and set it on the record player.
Once the gripper arm starts moving, what happens is this little switch right here on the top,
this one, which is switch number one, they call it. There is a little groove down in there
that that switch has fallen into to allow it to open. See how the roller is down in a hole there?
Let me brighten it up a little bit so you can see it even better. I'm trying to be as
thorough as I can on several of these videos so people can see what to check on theirs.
See how that roller is down in that hole? If you're not like that, the basket can't turn
because it thinks that the gripper arm is up. So what happens is when the gripper arm starts
turning up, this cam turns, and when it does, it closes that switch. Once that switch closes,
the basket can't turn anymore. That's part of what turns off the power to the basket.
So your basket will never turn when you put it in scan or operate if that switch is not open.
You have to be in that hole. And similarly, your gripper arm will never work unless you're in that
hole. Or I'm sorry, disregard that. We're just talking about the basket because that actually
changes state as that turns. So there are two voltages that the power supply puts out that
there is not an LED for. You wouldn't think there would be. Well, one of the voltages
is this turntable. So watch when I put it in scan, the turntable starts moving.
I'm going to show you why that is here in a second. There is a third motor that only
runs the turntable and it runs off of 120 volts. It plugs in right here where it says
120 volt AC turntable power. Now the two gripper motors are ran by 28 volts DC and they're ran,
I think it's 26 volts, 26 or 28 volts, and they're ran through this mechanism board.
That turntable is ran straight out of the power supply. So how do they turn it on and off?
Well, the CPU is doing that. So if you don't have this CPU in there, you can't get that to do that.
Let's test that theory, shall we? Let me turn it off and unplug the CPU and let's see if the
turntable will work without the CPU plugged in. Make sure I'm telling you the right information.
Okay, the machine is off. We're going to unplug these two connectors on the top which are the
power and the signals coming out. I'm leaving this plugged in. It's just telling the display
what to do. Now let's see if the turntable will work with that unplugged. So we have the board
unplugged. Turntable is not on. It's trying to turn a little bit. That's some kind of capacitor
thing, but as you can see it's not able to do anything without that plugged in. Okay, that's
because the power supply actually, I mean the CPU actually tells the power supply to turn on the
turntable. What I've figured out is that the CPU also tells the power supply to turn on the motors
that run the basket. So a lot of times whenever people email and call and say that their basket
doesn't move, they think it's the motor. It's hardly ever the motor. If you've got this problem,
your motor is probably fine. So I'm going to show you in the schematics exactly what's going on.
Okay, so this is a little bit of the Rockola 490 schematics. Now we're looking at the CPU section
of that control unit. So the control unit is running some things. I have a
plush crane in the background making a bunch of noise. So anyway, this is on the control unit,
that box up in the front. If yours is working properly, it's probably doing this. Okay,
so one of the things that it can do is it can send out and receive all these little signals here. So
one of the signals that it sends out is this run signal with a line over it. Usually when there's
a line over something, it means that it's active when low. So if that line there goes low, then
that run signal, as they call it, is active, right? So you can see that the board has its way of doing
it. It has a LS174 here, and that connects to a couple things, an LS32E3, and it runs through a
couple more things, and it's gated with different signals and stuff. And it comes down here and it
turns on a transistor and blah, blah, blah. But whatever, it can make that run line go low,
okay? So if it were to do that, that would be a low signal, right, that it's sending out. Now I'm
going to show you on the power supply what it uses that for. Okay, so here is further up the
schematics. They call this the rectifier PCB assembly, which is part of the power distribution
assembly. So this is that big box, the power supply we were looking at. Now just for to orient
you, orientate you, here are the LEDs that we saw that come on whenever the power is working,
right? So there's two there. So if this light is on, it is the 24 volts AC light, okay? If
this light is on, it is the 26 volt DC light. If this light is on, that means the negative 28 volts
DC is working. And if that one is on, it means the 5.7 volts is working. So if you've got those
four LEDs, then you've got most of the voltages, but there's two more voltages that they don't
mention. There's no LED for it. So one of them is this. Look, switched 120 volts. So switched
means they can turn it on and off. And look, it goes to the turntable. So our turntable, did you
see how it turns on and off depending on where that switch is, right? So how are they turning
that on and off? The turntable, by the way, just plugs right into there, okay? How are they turning
that on and off? With this little baby. Look at this, look at this thing. This is a H11C3
optocoupler, photo optocoupler. Now why in the world are they using that? It's because the way
these things work, this is a little chip inside of the power supply. Basically there is a,
like an LED inside of the thing, or I think it's an LED, that basically when you turn it on,
when you turn on that LED, there is a little receiver inside of it that can tell when the
LED is on. And when it's on, it turns on this connection. Now why do they go through all that
trouble? It's because they want to be able to control 120 volts AC, which is some juice,
with just a little tiny trickle signal over here on the other side. If they were to,
they would need a, you know, a straight up relay that'll switch 120 volts AC,
the thing would burn up and it just, it has the potential to short the other thing. So this is
just an easy way to do it, right? So, how does this optocoupler work? Well, it's getting power
straight from one of the, like it's a 12 volt line, it runs it through a resistor,
it says it's 1.2 volts DC on this one side, and then what turns on the other side?
So the LED, for it to turn on, it's literally a light inside of it, for it to turn on,
this side has to be connected too. This side is permanently connected to 12 volts through this
1k resistor. Well, what turns this side on? It's our run signal that we were just looking at from
the PC, I mean the logic unit, control unit 2, logic 2, system 2 logic unit,
right? So why is that important? It's because since the turntable is turning off and on,
depending on where the switch is, we know that that run line's working.
So here's the schematic of the turntable motor, which we're, you know, we're turning on and off,
on and off, on and off, and the only way we're able to do that is if the switched 120 is turned
on and off, and the only way that can happen is if that optocoupler is turned on and off,
which means that the only way that could be happening is if our run line is being used.
So we know that's working because the turntable's turning on and off. Now why am I showing you this?
It's so you can check it on yours, right? Leave your CPU plugged in and see if you can turn the
turntable on and off by moving to scan, scan, operate, off, whatever. See if that turns on
and off. If it does, then you know at least that line is running. If the CPU is not running on the,
in that logic unit though, you're not going to be able to get that to work.
Okay, so then what else does that run line do? Well, here's the interesting one. So that run
line connects to that, and then it also connects through this resistor, a 1k resistor,
right down to here, boom, right there to that capacitor, which is across
this coil, which is a relay in the power supply. Okay, so if that is not connected,
and this relay is not pulled in, one side of the relay is connected to 45 volts. Okay,
so 45 volts is coming from over here at the transformer. All right, so one side of the relay
is always connected to 45 volts, but the other side
doesn't have a connection unless that line goes low. All right, so why is that? It's so that
that same run signal can turn this relay on and off. So what does the relay do? Well, if the relay
isn't pulled in, then you have a normally connected situation here where this line,
which is the ground from the transformer, the center tap from the transformer,
connects to this 24 volt DC line here and basically shorts it out. So why does it do that?
Right? I may have it backwards of what it does when it's on or off or whatever, but
basically it connects to there and shorts this to ground. Well, what that does is it makes this,
the input to this LM317, it's getting 45 volts on one side, it's getting ground here,
and it can, it's basically turning on and off the switched 26 volts. Not to be confused with the
26 volts. There's two different outputs. So there's a 26 volt and a switched 26 volt.
So there's no LED on the switched 26 volt. Now I know this is really confusing.
The switched 26 volt is, are you ready for it? It's how it turns on and off the gripper motor
and the mechanism motor. So we know that that signal works, right? Where are we?
We know that that signal works down here to turn on the relay,
but it's either not turning off the relay or not turning on the relay or something,
something's not right. And that's why you're not getting this voltage out. If you check this
switched 26 volts, which is a red and blue line coming out of the power supply. And it,
it goes over to the, uh, that switch we were talking about on the cam on the front of the
machine. If you check on that red and blue line, I'll bet you, you don't have 26 volts there. And
that's why you are not getting your, um, that's why you're not getting your motors turning.
So a lot of people think, I think my motor's bad. And they buy new motors. Those motors don't
usually go bad. They're like the last thing to go bad. It's much more likely that some of this
crap's going to go bad. So you know what usually goes bad? Uh, that relay. So look how they've
designed it. If the relay is closed, you have just shorted this to ground. So this 24 volts
isn't there because now there's ground, uh, on both sides of this, um, uh, Zener diode here,
24 volt diode. So it basically takes it out of the equation. If that's open, now you've
got the Zener diode in play and it raises this up to 24 volts because it's using it.
It's basically using the output of the, uh, the voltage regulator there and all this. It's an
adjustable voltage regulator, right? So if this, if this little relay is bad, that's going to cause
all kinds of problems. That's what's wrong with mine, I believe. So here's the next, OK, so if,
if that does pull in, it can also send ground to this connection. So what does it do?
Well, if you look on the schematics, see the line going up there? It connects up to here,
which it calls audio control. So it says audio system socket. It's probably something that turns
on or mutes the, uh, mutes the jukebox or turns on the jukebox. I mean, not the jukebox, the
amplifier, right? So why would they do that? Well, once the gripper arm is doing its thing
and it's in this position where it's supposed to be or whatever, maybe, I'm just guessing,
maybe the, the, um, control unit turns off the motors, the power to the gripper arm and the
power to the, the, uh, basket and turns on the power to the output of the amplifier.
That's why it's all muted until the record starts playing and then you hear it pop on.
That's what I think. That's probably how they're doing it. OK, so all of that to say,
if you're, if that, that's some things to check and the order to check them in to try to tell
what's wrong with yours, right? So if you don't understand exactly what I was saying, go back and
watch through the video and maybe you'll catch what I'm talking about. You want to check your
power supply. You want to check the lights on your, on your logic control unit. You want to
check to see if the turntable turns and turns off, which is also important, right? Because that will
tell you if this run line is working. And then finally, you want to check the output, this
voltage here, and see if your switched 26 volts is going out on the red and blue line coming out
the power supply. If that never comes on, then of course your motors aren't running
because you don't have the voltage for them to run. So let me show you what the mechanism board
does with that voltage. So the power cable comes down here and it plugs into that board in the
front I was talking about, which is the mechanism power board. OK, now depending on which version of
the machine you have, that thing actually may actually be on the back, but it'll say mechanism
power board right on it, right? There's a couple different designs like I said. There's a little
six pin connector that plugs in. And so one of them is a signal that's called cam one. I think
that may be actually a signal back to the board. There's a home switch signal here. Now that's
basically so it can tell when it gets back to the home position. There is an A and B and then look,
here's our 29, they're calling it 29 volts at this point, 29 volts DC switched. It's that same
red and blue wire and it plugs in at pin 5, right? So if you look on here, pin 5 on the actual board
comes down and it goes all around and it comes up here and boom it goes to the fuse. So if that fuse
is blown, of course the board can't use any of the power. But that's how the power gets on the board.
The way they turn off the motors is they can be completely turned off by the power supply,
which is turned off by the CPU. And I was just thinking, since they use the same line to make
the turntable turn on, they can't turn off the power to the motors if they have the turntable
turned on, right? Maybe the turntable has another way of getting power or something.
Okay and then there's a few switches, I'll show you two on that cam, that can turn things on and
off. Okay so we finally made it to the motors, the magazine motor and the gripper motor. So you see
like if we're looking at the magazine motor, so I can't get it to turn right now, one side of it
and the gripper motor is connected to a red and white wire which comes off of the mech board,
right? And then the other side, the magazine motor gets its power through the pink and blue wire
that is connected through that switch number one that I was talking about, right? So this switch,
if it's down in that hole, the basket can get power, the magazine motor as they call it,
and then if it's out of that hole it connects back this way which sends the power up this way
to band five blah blah blah and does some other tricky stuff, right? So that's what you need to
look at. So I'm interested now in how the, when it would turn off the magazine power.
I guess it would just turn it off whenever it's also going to turn off the turntable.
Yeah, so there must still be voltage on that line. Oh yeah, it has to be. So there has to
still be voltage to the mech board while the turntable is turning because it still needs to
be ready to hang up the, reverse the everything and hang it all back up, run the motors in reverse
and all of that. So the actual gripper motor goes both ways. It has to lay it down and then it has
to pick it back up again too and put it back in the basket. So it has to run either way. So they
have a little set up down here where they make it go backwards. How does that work? And seven
a reverse relay. It seems to reroute some of the signals to make the power go to one side or the
other. All right. So anyway, all that to say, I think that relay is bad on my power board. So
I've ordered one, but guess what? You can't get the one that's on the actual power supply. They're
obsolete. Apparently this is a problem that people are running into in all kinds of vintage audio
equipment where they use these little relays that you can't get anymore. And so the footprint's
different, everything on it's different. So I've ordered a substitute. We're going to rig it up
in the best possible way. We'll consider it an upgrade, but we have to replace that and we'll
see if that gets us up and running. So I'll show you what that little board looks like
on the bench. Let's check it out. Okay, folks, so I've got the power supply out of it.
Okay. This is the board that we're looking at on the schematics.
There's a few capacitors in there I want to replace. Someone will order those too.
All of the fuses are fine. And I've got it set up. Now be careful if you're messing with this,
don't do this. Now, if you decide to do it, you did it against my wishes.
So the thing is you can plug this in just outside of the machine and check your voltages
and things from there. So if I plug it in and turn it on, I've got all four of my lights on.
Now those lights, by the way, that doesn't necessarily mean that the voltage is perfect.
It just means that there's some kind of voltage there. Okay. Now this is the relay that I'm
talking about. This is a, I'm going to turn the camera instead of turning the machine.
It is a Potter Brumfield R50-E2-Y1-24VDC. So that's a 24 volt relay and it's just a one pole.
So it just turns, goes from one connection to another. There's a two amp, the coil can handle
two amps and the one amp draw and it can handle one amp on the 120 volts that can run through
the contacts. That is this area right here. Now again, if you look, the normally connected shorts
over 1N4749, which is a little diode. Okay. Now with the thing turned off,
notice I have replaced that diode. I've been messing with it. I messed with this last night
and I decided I better film this. With it turned off, that diode is at a direct short across it
because that's normally connected. So we need this relay to pull in and move this
away from here to here, which will allow this to pull the 24 volts or whatever from the output
to make this output properly. Okay. Okay, folks. So we've been ordering all kinds of parts.
Not all kinds, just a few. And I have replaced the major capacitors, the bigger capacitors
on this little board. But our main problem we think is with the relay. So here is the relay.
It's an R50-E2-Y1-24VDC. This thing's completely obsolete. They haven't made it in forever.
You can't get anything that's even similar to it because the footprint is strange.
So these two outside ones here are the coil, 24 volt coil. So when 24 volts goes to that,
this is the common. It connects to this inside post here. That's the normally open.
This outside one is the normally closed. Okay. I'll show you a little drawing of the schematic.
So if you can kind of tell what that is, basically, you know, when the coil pulls in,
it pulls it from one way to it's connected the other way. Okay. If I don't drop it on the floor.
So the coil, if you test the resistance across the coil, it's like 700 ohms, which should be fine,
but it just, it isn't working. So it must be, if it pulls in, it's not connecting this pin
to this middle pin here. But this pin is connected to the top pin. Okay. So that's
the normally closed position. When it pulls in, it should change this pin to this pin,
but it's not working. So I Googled this thing and there are a few of them out there. They're
trying to get $200 for this thing used because apparently it's in a lot of vintage audio
equipment, which must've been where they got the idea to use it in this jukebox. So I looked
around, I said, you know what, I'll, I will just order another 24 volt relay and then I'll just
wire it up and it won't be no big deal. So I looked online, made sure to get one with the right
specs. So this one is, if you're running one amp through it, I mean, if you're running 120 volts
AC through it, it has one amp rating on the contacts inside of this. You can run up to an
amp at 125 or 120 volts AC through it. But if you're running 28 volts DC, which is pretty much
what we're running, this is like what, 26 volts DC, you can run up to two amps through it, right?
So this thing needs to be rated for two amps, my replacement one. So I look online and I find one
and I find one that's rated two amps. It looks pretty good. I was like, oh, okay, let me order
that. So I ordered it. It's like $2. I order a couple of them. It comes in, it's this little
tiny relay, right? Look at this thing. So it's an Axecom 1M07. But it's rated for two amps at
28 volts, or I think 30 volts DC. It's rated at two amps. So it's got the same rating,
but look at it compared to the other one. And so I've looked and looked and looked and read and
read and read and I read this data sheet and this data sheet. I think it's the same rating, people.
It's just really small. That's not really the best one to use though, because it just, it's so
small that the leads are so close together that it's harder to use, right? But what I did was I
very carefully attached wires to it and then put shrink wrap on the wires so they wouldn't touch
each other, soldered the wire to the legs and then ran the legs down into the board, into the five
holes that the original relay used, right? So the two of them are for the coil, one of them's the
common and then the other one is the two contacts that switch back and forth. And I got it all
wired up and I mean, you know, I've got a some heat shrink on it, put a little zip tie on it
and everything so it can't short out or anything. It's just kind of sitting there. It's so small,
I mean you could, you could zip tie it to something else. This is not really the best one
to use. I wish I had a bulkier one. So I may, I may order one that's bulkier, but it is rated
the same. So technically it should work. Okay. So how are we going to test it? Well, on the
schematics, it's got that run signal illustrated, right? So that run line comes in and it's basically
grounding this up here, which is the optocoupler we were talking about, which turns on the 120
volts. And then also through this resistor, it will turn on our relay, which is this area here,
which will turn on our 24 volts. Okay. Which will make our switched 26 work, right? So we're going
to try it. Now I've got the multimeter hooked up on the output of that. Let me turn it on and we'll
see what kind of voltage we get. Nothing, but it's all on right now. If I ground that run line
to where it thinks that the CPU is telling it to turn on the run line. Oh, I'm on AC.
That won't work. There we go. So I've got 24.85 volts. If I turn the ground, the run line off,
we have 2.4 volts DC. Okay. We'll put it back 24 volts. So it now should be able to turn on and off
the motors. Very cool. Okay, folks, we've been doing a lot of work on the machine.
We've been working on the control unit, the amp, the mechanism, the lighting, which was actually a
really big problem. We had to put a fluorescent, a more modern ballast in it and take all the old
ballast out and rewire half of the stuff. If you get a problem, by the way, where your computer
keeps going back to initialize and it's doing it over and over again, or it sticks over there.
If you have a light bulb that's blinking, it'll make it do stuff like that because it's screwing
up the voltage that it needs to boot. Okay. But I just wanted to show you, I've got the lid
carefully leaned down here. As you can see, we have that new relay in there. All right.
I'm going to show you what this thing is supposed to do when you turn it on.
Just so you'll know if yours isn't doing this. Okay. So it's off. This is what you should get
when it comes on. It moved just a little bit. Yours may or may not do that depending on where
it's at or that may be a capacitor thing or something. So you've got that. And then
as it's scanning, the turntable will move because it's using that home line that we were talking
about. Now that means that relay is working. All right. Put it back in operate. And then if I pick
a record, now I can't play a record right now, people. But what I'll do is I'll pick up another,
I'll do another small video that shows one plan. But as you can see, everything is working.
We already had our control board working. So what it ended up being was that relay.
And you can see it's up and running in the cabinet. So if you have an issue where
you can't get anything to turn at all, it very well could be that line on the power supply. So
you kind of need to check that. And kind of a giveaway. Well, I don't, you know, the turntable
moving. I don't know if it actually needs the relay to work because it's using that optic
actually, that coupler. But there you go. I hope that helps you with yours. Check the relay. I
believe I've had several that have that relay bad in it. I've had a couple in the past that I swapped
the entire power supply out in it. And looking back, I think that's what the issue was. Because
you'll get all of your voltages, but if you don't check that switched voltage, because they don't
really mention it and they don't have an LED for it, you may not know that. They're blowing me up
on the phone, people. So I hope you enjoyed it. We'll upload another video of this thing actually
playing just so you can hear what it sounds like. We've got a ton more videos on especially
rockola jukebox repair. So check those out on our channel here. Make sure to give us a thumbs up for
the trouble to film it for you. And leave your comments down below. Now, if you want to know how
you can support our channel, I may have mentioned it earlier, but there are links to Amazon down
below if you're going to buy anything on Amazon. They may have that relay on there. If you're going
to buy anything on Amazon, click our link and that'll take you to Amazon and then you can
browse around and anything you buy gives us a tip. So we appreciate everybody that's been doing that.
We will see you on the next video.