Thank you to everyone who has been supporting our channel! If you use the link below before you purchase anything on Amazon, we get a royalty for sending you there, thank you!
Our store is located at 139 Caldwell St., Rock Hill, SC 29730.
ladies and gentlemen this is Joe's
classic video games back with another
cool pinball repair video for you this
evening this is got lib's fantastic
Spirit of 76 pinball machine we've been
working on this for the last couple
videos
and uh I think we've done three videos
on it and
we've got the thing halfway limping
through its startup procedure if you
didn't watch the previous video we went
all through how the player unit Works
figured it all out and then uh came to
the conclusion that we need to clean all
the score reels
so we messed with a little bit and we
got the game to start it kicked the ball
out it scored a few things and then it
would just stay on ball one the whole
time so we've got to figure out why it's
doing that the play field here in one of
the videos we repainted a lot of
so uh it was completely trashed
so a lot of this has been repainted and
it looks a lot better than it used to we
put of course all new rubbers light
bulbs stuff like that in it so if you
didn't see those videos go back and
watch them so here we are
we got to get this thing to reliably
start up if you didn't see the previous
video basically this player unit spins
around it gets to position 20 and it
turns on this reset relay that resets
these eight score reels once they reset
the zero power connects through all of
them and makes that move one more spot
that moves one more spot and it turns on
this reset relay which then resets all
of these score reels
once that gets all back to zero power
runs through them and makes this rotate
back to the first position and the game
starts
so when last we left it I kind of messed
with these just a little bit to limp it
along and then these weren't connecting
right so by shorting some switches
together we got it to go around to its
first position and kick the ball out so
the very first thing that I want to do
is clean these score reels properly so
that I don't have to shorten anything or
mess with it it's just time to do it
this is my least favorite thing to to
um
to do on these pinball machines but uh
what I'll do is I'll start working on
them there's 16 of them we have to do
I'll just show you one of them and uh
what what needs to be done to get the
thing reliably moving and resetting and
all of that okay so this one's probably
going to be the worst one see all the
rust here remember there were rats and
stuff all in this machine
uh so this is got the decagon score reel
originally these actually had flat spots
where the digits are
and so it made more sense to call it a
decagon but this little board I believe
was on the earlier ones that had that
and they just kept using it but um
yeah so you want to take these two
screws loose to take this board off and
there's a little
c-clip here you have to take loose
so when you get those off you end up
with this you can see how
filthy that is
that's the remnants of some kind of wax
or oil grease
that they originally had on it
and so on this there's a little clip
a little plastic thing
here this is one of the problems if they
put some kind of grease on it it gets on
this
and then after a while it hardens and so
it's kind of sticky whenever you're
touching it
and then your problem is
if I can get it to go back down
this wheel sits down there like that and
then that little plastic piece I just
took off sits on this metal but it has
sticky stuff all over it which is
nothing but friction so as this turns
it that's one of the places that it
hangs that little
clip there
and then also
the inside of this so if this is all see
how it's yellow in there that's some
kind of
gunk
and it's on all of them every one I do
so there must have been some kind of
light oil or something that they put on
it at the factory
you're not really supposed to put oil on
nylon touching metal but it's the
factory so I'm not going to say that
they didn't do it right it's just you
know I usually don't
but you need to get that as clean as
possible and you need to get the shaft
of this thing to clean one way you can
tell is if you so this is the next part
same thing
there's like a sticky
substance all over it
right
and then it there's a little nylon piece
down here as well
so when this pulls in
see the little gear there
that's going to turn this
and so you've got friction all on the
inside of this
and the outside of that
so if there's grease and Gunk all over
that it doesn't turn right so you need
to get that clean clean clean
clean clean clean now look at the plate
behind it so see this plate and then
look down in there
see all that that's more grease that
somebody has put in there
so you need to just get it as clean as
you possibly can so that it will move
properly and then I'm going to show you
a trick with these switches once we put
it back together
oh another thing that's very common is
this blade will be bent in half about
right here
if it's bent you need to bend it back
straight but the top is bent the top is
supposed to be bent
but you'll see them like that all the
time or much more severe
I'm talking like half of them will be
like that
so you need to be straight like that
okay so here's the problem you run into
hopefully I can illustrate this with one
hand
I'm going to pull on this plastic piece
which is going to pull the plunger in
and show you how it advances forward
so I'm trying to do it fast which will
mimic the way it does it in the machine
right now watch what happens when you
get to position nine
so I didn't quite do it
like it didn't quite turn all the way
you're locking the place
and now
it goes to zero pretty easy so this
one's a little easier because it doesn't
even have the nine position switch
there's a since this is the
last score reel it doesn't do anything
when it goes to nine but there's another
switch up here and so this little this
little cam here makes the magic happen
and so I'm going to show you what it
does and I'm going to show you the way
that you can
the the Forgotten switch that people
don't mess with that causes a lot of
problems so it's on zero right now so on
this particular design the bottom switch
closes at zero
and it does that so that power can run
all the way through all of these eight
bottom score reels
to bypass the switch on Z2 that is open
since it's pulled in and the power
running through that will advance the
player unit to the next
uh position we went over that in the
last video extensively you see how this
middle switch is open
that is the run out switch for when it
resets
so basically when it's not on zero that
middle switch is closed
and that middle switch allows the Z1 and
Z2 score reset relay relays to keep
pulsing this
but when it gets to zero which is reset
that switch opens
and breaks the connection so it can't
reset it past zero that's how you want
it
right
so during normal gameplay
the score reels on these particular on
these particular games are just uh the
the the
relays the real one the solenoid on it
is just wired to the 10 point relay 100
Point relay thousand Point relay
whatever right so we're on zero right
now so watch what happens when we go to
one
foreign
isn't adjusted right
that should be closed at one
and you could kind of tell
because of the big gap on it right
so we need to adjust that so it's closed
and then it's going to keep on going
and then let me show you what happens
when it gets to nine five six seven
eight
watch is going to go way up
or try to right since I did it slow it
won't even do it so it has to push
remember this one would have been even
farther down
and it has to push way up
to close the switch up here
so it has to move that so far but you
know what it really has to move far this
bottom one
so people will adjust this middle one
and adjust the top one and they'll oil
the hell out of the thing and they'll
shorten the spring and all kinds of crap
but what really is going on is this
bottom switch
not not this one the one that's in the
unit look how far that is bent out of
whack
but it has to it has to do that to get
up to touch this nine ninth position
switch that isn't even on this one
so the problem is you need to bend that
one farther up so that it doesn't have
to bend it as far up the way it is right
now
it's pretty it's causing all kinds of
tension
okay so see it way down here
if it were up a little farther
that would be fine this could push it
down
to zero so bending it up
will make that that transition to nine
easier because it won't have to bend it
as far up it's already a little higher
up so we need to bend that switch
slightly higher
and that may even fix our problem where
at at one we're gapped out right so I'm
going to bend this bottom captive switch
the one that's in the
Armature I'm going to bend it just a
little bit higher we'll see if that
helps our problem
all right so all I did was adjust that a
little bit
you might have saw this top one was all
kind of bent up over here I just bent it
back straight and see where I've got it
I've got the it where it comes out and
it's almost it's pretty much straight
right but I bent this long one
up higher
that's where the the freaking issue is
it's it's completely counterintuitive
you would think oh you know it has to
push that nine one all the way up this
one doesn't even have an ammo but it has
to push this one all the way up it's the
bottom one it has to pull it up causes
all kinds of problems
so we are at zero
one see now the middle ones are closed
right
one two three four five six seven eight
nine
zero
so when you need when you need to fix
that
that bottom switch is your problem
all right so here's one of the ones with
the nine position switch
at the top there
so I've already adjusted this one
we're at zero now and of course I took
it all apart and cleaned it we're at
zero so that bottom switch is closed
if we go to one and now the middle
switch is closed and it will stay closed
the bottom switch is open
and the top switch is open which is the
nine position switch
all right so six
seven
eight
nine
this one up and touched nine
see the middle still closed watch look
how far it needs to travel to to shut
that bottom one
and it does
middle one's open
right
so the reason these don't turn right
a little bit of its you know friction on
the on the plate a little bit of its
friction from dried up grease but most
of it is the tension on these blades it
has to be just right
and you can have it working just right
but this won't turn because of the the
tension that these provide on this so if
if these are pushing this way down
that little bar in there is pushing up
against the bottom of this wheel and
it's it's more friction and won't allow
it to drag to turn
perfect
that's perfectly how it should be
all right folks it's been a horrible
experience but I gotta I got them all
cleaned let's see if they're reset
sometimes if you're in the middle of a
game whenever you turn it on it does its
thing but we'll see if it just goes
straight to tilt
yes it did
or keep a game over actually
okay so we're gonna try to reset all of
them
now there's also tons of other problems
light bulbs stuff like that but
we should have the score reels done
let's see
you're going to see something incredible
if it works
[Music]
one hung a little bit boom
I don't know was at the end I don't know
it keeps doing that
sounds like it's the
sounds like it's that doesn't it
Let's uh score something and then see if
it does it every time
foreign
yeah it does it every time is that right
let's see if it's
actually physically moving every time
[Laughter]
that ain't right
but it did uh they did all reset we had
that one hung just a little bit might
have to look at that a little more but
uh
we've about got our score reels ready
so next up let's see if I can figure out
why the out hole is kicking four times
like that it shouldn't do that come on
people all right so on the schematics
here this is the ball return now
the clue is that it does it multiple
times
doing it like five times
well that's because it's it somehow must
be connected to the impulse of the cam
so there's lots of things that do that
happen five times like if you score 50
points the 10 point relay fires five
times you score 500 points 100 Point
relay fires five times if the score
reels are resetting they're pulsed five
times
right
so a switch like that must be involved
here somewhere so here is the ball
return and if you travel back
it runs through a switch on
uh I need to get out the paper ones but
is that ox
and then a switch on o which is the out
hole relay
so the ball has to be an owl hole and
then to switch motor 4C so whenever the
score motor is turning eventually it
will close switch motor for C
and the way that gets power
is from this lead here
it continues down and it is pulsed by
motor 1A
so did you follow that basically for
that coil to fire the power will never
get to it unless switch 1A
on the score motor
and switch 4C on the score motor are
both closed
so switch 4C this is the motor sequence
chart which is basically like it shows
you kind of the timing of everything
so as that score motor starts turning
it's it's closing all of these switches
and the black lines represent not
necessarily when a switch closes but I
also when a switch opens so just
anything that's stacked on for instance
position 4C
um will open and close depending on how
it's wired
at that point
so this is the home position the zero
degree position instead of score motor
starts turning and then when it gets
over here to about
100 degrees
that switch will close and stay closed
till about 115 degrees
right now they could also have one that
was open I mean that was closed
and stays closed
until it gets there and then it would
open at that area so it's really when it
changes its position you know
um and it just depends on what you're
trying to do how you would wire that but
the home position
is back here
okay and as the score motor turns it can
there are three home positions so it
turns a third of a revolution from home
position to home position and that's why
it says 120 degrees
the second one would be technically 121
or would be technically 120 which is
where the second home position is
to 240 and then the third one would be
240 to 360 which is 0 to 120 and so as
it turns it's just going a third at a
time right so
Sherlock Holmes could say
that if this
if 4C has to be closed for the ball
for the kicker to kick the out hole the
ball return coil that's what it's called
the ball return coil
to kick
if 4C has to be closed
and one a has to be closed
well you see 1A closes five times
now why would they have it closed five
times if you only needed to close one
time it's because there's other things
on this stack
there's not just one switch at one a
there might be four or five switches at
one a and it's just doing other things
so what they've done is this is the same
set of switches that works whenever the
game resets
it's what is resetting the score reels
and all that stuff
now if the reset relay or the the score
reset relay
um Z1 and Z2 if they're not pulled in
whenever these close on motor 1A
whenever that particular switch closes
nothing happens because that relay is
not pulled in
and so it has cut the the path to power
similarly on this one that ball kicker
will never kick if the ball is not in
the out hole because then the O relay
will never come on
and so this keeps turning and these
switches keep closing but the power
never gets all the way through you know
it goes up and goes to one switch and it
makes it through that one and then it
goes and it makes it through another one
but then damn it that o relay is not
closed then it can't go through that
so they control it by turning on and off
relays that are in the way of the power
it's like having doors closed or doors
open you know
so in this particular instance this is a
really interesting one because you can
the op the answer is a parent right the
way it's wired up 4C has to be closed
and see see where it is and then 1A has
to be closed ours is kicking five times
why would that be
it must be because 4C is stuck closed
that must be closed the whole freaking
time
and every time this closes Bam Bam Bam
Bam Bam it's kicking the freaking ball
out
so the problem almost has to be for sure
4C so if we go find that switch
that ought to tell us now how do we know
on 4C if there's four or five different
switches how do we know which one it is
you know by the wire colors so this one
is uh White I think it's yeah white and
black and this one is orange and black
this one says white and black on another
part of the schematics
um
so orange and black white and black so
you look on motor position 4C until you
find the two blades of the switch that
have an orange and black wire run into
it and a white and black wire run into
it and that's that
switch
all right so
see the number four there that may be
missing on yours
but this is the stack four
on the score reel
okay so here we are a is at the bottom
it's that one that's crooked
it's still on a is here B is here and
this is the C switch stack
and I said orange and black it's orange
and blue so orange and blue is this
outside switch
and then the next blade down
has a little blue jumper on it
see it
and so that little blue jumper
must be jumping
somewhere
yeah
so it's jumping to the white and black
wire
okay
so we have confirmed it's this outside
switch now you saw how it was drawn in
the schematic that switch is supposed to
be open and it's closed
but you can see why it's closed
see these little spacers here these
little nylon things there's one missing
there
so they have a stack of switches
and since that nylon piece is missing
it's not pushing open that second
stack there with the nylon
so luckily I've got a bunch of those so
I'm gonna go get one and see if I can
get it in there where it's supposed to
go and fix that problem but as it's
sitting right now
let me show you from the other side you
may be able to see it better
see how the little follower there
on the cam
is pushing the first switch down there
closed
but the second switch should be open and
the third switch should be open
oh don't electric kill me people
what I do to show you the cool stuff
oh don't electroshock me
so it should be like that
because there's a little plastic spacer
that should be in there
get it got it good
new one installed
they sell those brand new you can get
them at the pinball resource uh you can
get them at Marco's Specialties now if
you're working on one of these you can
see the importance of the schematics
how in the world would I have found out
without the schematics
you have got to have the people you've
got to have the schematics it's 20 bucks
it ain't that big of a deal
you can get them at the pinball
resource.com pbresource.com
uh they just help you fix everything
and without them you know what are you
gonna do
it helps you figure it out it's like a
big puzzle it's part of the fun of it
that's that's another thing that people
don't understand
this is fun people it you must think
it's fun or you wouldn't be watching
this deep into the video this is the fun
part it's like a big puzzle have you
ever done like a crossword puzzle or a
Sudoku
you know it's like a little mystery
you're trying to figure out hmm that's
not right it shouldn't be doing that let
me get the schematics and figure it out
that's the fun part of it it's like a
it's like a little challenge right
so that should fix it
um but let me light a play field down I
turned it off while I did that and we'll
restart it once again
and see if it kicks the ball out five
times or one time here we go
thank you
foreign
beautiful wasn't that beautiful let's do
it one more time
[Music]
the other noise you heard I think was
the uh
the drop targets resetting let's try it
once more and watch the drop targets
did you see him Thump A little bit there
so it's going clink and then it's going
Gunk the glunk
is both sets of drop targets resetting
okay so uh solve that problem let's find
some more problems to solve
so I tried to test play it
and it was disastrous
the drop targets won't drop cleanly they
only drop like halfway so we're gonna
have to rebuild the drop targets
which isn't a big deal
all right folks I think we about got it
I had to replace some light bulb sockets
adjust some switches but nothing major
so let's see
notice the drop targets reset crisply
all right everything reset to zero it
says ball and play one
player one
[Music]
we still got two
we gotta fix the Chimes
[Music]
hmm
flippers are pretty strong
oh
you get a good flip oh yeah
that's how you want it
beat up the banks
[Music]
missed it
all right
I get a lot of people saying Oh The
Flipper buzzes
that's a thing on em pinball machines
people they're AC powered
you can maybe get them quieter if you
replace everything and then they'll
start doing it again and then you can
spend some more money and replace it
again
now on a more modern pinball machine
they don't typically do that as loud
[Music]
oh
George
I think it's George
[Music]
I hadn't seen George in a while thought
he might have something to do with that
that was crazy
he had a chime sound like crap
but it's playing fairly smooth really
oh kissed
[Music]
so there's no thousand Point chime
George
what are you doing
see if this is better
[Music]
straight down the middle ball five
foreign
[Music]
oh yeah
that's how I like it we made it more fun
folks
want to get a good whack on this right
one
yeah we're good
[Applause]
Okay so
basically we had a situation where the
ball was getting cupped getting caught
and a slightly cupped insert
so what's going on is there's a little
tiny divot on the bottom of that insert
there it was just a little tiny thing
now if you didn't see the earlier videos
we repainted like the whole Playfield
and it it the thing was in pretty
extreme
extremely bad condition
um so there's just a little bit of a
divot there in that
so if you hit the ball just right it
bangs around up there and since it's
heading this way really slow it stops on
the insert
almost looked like a ghost was doing it
on purpose right
so the way you fix something like that
is you increase the
well there's two ways to fix it one you
can fix it by clear coating it
so take everything off the play field
clear coat it sand it down clear coat it
again sand it down clear coat it again
sand it down clear coat it again sand it
down and then in 2025 whenever uh uh
well I can't talk about
in 2025 whenever horrible things are
happening to the country you may finally
have it flat
right
but uh uh
or you can just make it a little steeper
where the ball rolls past it a little
faster
but you can't do that if the flippers
aren't strong enough
but these flippers are pretty strong so
it's there's still no problem getting
the ball all the way to the top of the
Playfield if you increase the that this
the uh pitch of the Playfield two in my
opinion it makes them play a little
better because it makes the ball roll
faster
but you can only do it if you've got
strong flippers and we've got strong
flippers so uh I'll keep playing it but
I did find something else that we need
to need to figure out one last thing
I need to paint a little bit on the back
glass but other than that one last thing
let me tell you
okay so I don't know if I can get it to
show you
so the problem is the first player and
the second player lights are lit up
I haven't messed with any of that yet
replacing any of those light bulbs but
whatever that is is going to be a
problem like
on something else on the player unit or
something so we need to look in the
schematics and see
if I'm playing a one player game why are
the second player lights lit up
so you simply look in the schematics and
see what lights up the second player
light all right so here are the second
player score lights and I have to admit
I've never really understood why this is
but
if you see here this is a switch on the
player unit whenever you get to the
second player's set of switches and
we've went over that player unit several
times already but whenever you get to
the second player's stack of switches it
turns on the lights but there's also a
switch here on BX which is the last ball
relay
uh that I believe comes on whenever you
get to the last ball so if you're
playing a third ball game when the third
ball starts
that relay comes on
but it looks to me like it comes on
when the first player gets to the third
ball so I don't understand why they
would turn on the second player's lights
as well
um but that
that's how I read it I don't know I may
be wrong
but you know on the first player it does
the same thing now the third player
the Q relay and the fourth player the Q
relay that's the game over relay
so I don't I've never completely
understood why that works like that but
whenever you get to the last ball
it turns on the first and the second
player's lights is how I read it
and
um
when you get to player three
if you were playing like four player
game player one and player two's lights
would be one and player three's lights
would be one but then whenever you move
to player four player one's lights would
be on player two's lights would be on
because the last ball relay would be on
player threes lights would be off
because the you're not on player threes
reels and the game over relay hasn't
been tripped and then player four lights
would be on
that makes zero sense but I'm I must be
I must just not understand it
um
maybe the last ball relay doesn't come
on until the end of the game I don't
know but anyway our problem is the
second player lights are on all the time
so it's probably that switch
it's either the switch
um
on the second stack of switches on the
player unit or it's this switch on the
BX relay one of those two is always on
and that's why those lights are always
on
all right folks I have found our
offending switch for uh making the
second player lights stay on so we're
back to the player unit now if you've
been watching the whole time you know
this player unit's giving me all kinds
of trouble
so we're on player four right now
got my hand in the way
we're the reset area
That's player one it makes these stack
the stack go up you get to the next
position it's going to make player two
go up but if you look really close at
the second set of switches
not the top two the bottom two
this house already closed
and now it's still closed and now we're
on the player three but the second
player one is still closed
that's what we're talking about
that switch right there
that should be up like that
so I'm gonna bend it just slightly and
that should turn off our second player
lights and then just for curiosity's
sake we're going to play or just step
through a uh four player game
and see on the last ball
how the lights work on the score
displays because that makes no sense to
me about that last ball relay well it's
daytime so you can't see too good but it
did reset and it has fixed it where only
the player one lights are on so let's
play a little bit
oh I need to start more than a one
player game
so that's resetting it one player game
two player game
see the lights at the bottom four player
game
okay so we'll act like it kicked the
ball out
all right we'll let it play itself a
little bit
so only the first player is lit up
so now we have moved over to the second
player and only hit is lit up
now we've moved to the third player and
only it is lit up
but that third player is pretty good
okay now we've moved to the fourth
player and only it is lit up
so that's ball one
back to the first player okay
so
let's step through it
ball two second player
ball two third player
all right
okay so we're on the fourth player ball
four maybe if I turn the lights out we
can see it better
bright out
fourth player Ball Four
[Music]
okay so first player ball five
second player ball five that's how I
would expect it to work so the last ball
relay must have not tripped yet
third player ball five
fourth player ball five yeah so they uh
it doesn't light up like it
so the last ball relay must not be
pulled in let me check okay so the last
ball relay is this interlock relay right
here and it is not tripped yet we are on
player four ball five so it doesn't
happen
on player one ball five
so let me hit the runway switch
that doesn't trip it let me score some
points
that didn't trip it
okay
and then let's
land in the out hole that tripped it
so the ball Landing in the out hole
tripped it which turned on two sets of
lights and then the other two turned on
with the game over relay I wonder why
they just didn't put all four on the
game over relay must be a good reason
all right folks so this part's fairly
complex
so the power connects through here the I
relay is the extra ball relay so unless
you've won an extra ball so if you
haven't won an extra ball that's still
connected so power connects through here
the u relay is the first ball relay and
it's an interlock relay so as soon as it
trips as soon as the ball has been
played that closes and then you get to
the coin unit
this is drawn as a one player game on
the first ball as with the ball sitting
in the out lane in reset position
basically so if you've only got a one
player game these are connected
and if you look this says 2B 3B 4B so
that one's second player third player
fourth player so if I was to play a
second player game this would move and
this would no longer be connected but
this one would still be connected and
this would still be connected those are
basically they're shorting out the third
player and the fourth player that's how
they get it to advance past the third
player and the fourth player if there's
only a two player game going on so power
comes through here
and on a one player game Power connects
through here
at position eight there must be a
position zero which must be where we're
starting
so you know ball one zero through ball
one is player one player one ball one is
position zero player one ball two is
position four player one ball three is
position eight
so this is player one ball three so if
you have this little jumper connected to
three
when you got to position eight
which would be ball three
the power would connect through this
through here and as soon as the out hole
relay closed which is the ball falls in
the out hole
it would turn on the last ball relay so
it does it after the last ball that's
kind of interesting
um and so let's say you play a
two-player game
well that short moves down to here so
when you get the ball eight I mean
position eight that's the first players
third ball at the end of that ball
it's not connected because that has
moved because you got a two-player game
this one's still connected so when you
get to position nine which is player two
ball three at the end of that ball
as soon as the out hole curve closes it
will turn on the
um last ball relay
and then if it's a phone Fireball setup
it Wade still position 16 17 18 and 19.
so uh it makes sense I just don't
understand why they did it like that but
this it's working correctly
all right folks so here is the beautiful
back glass
I've went and triple thicked it
see the shine
all the parts that were flaking
are now sealed with triple thick we've
done that in a million videos
but I wanted to show just the condition
this one's in before we touched it up
this is going to be an easy one because
it's just the red basically
so this is some kind of red cable
that the astronauts got going to his
helmet or something
it's flaked
the Spirit of 76 part
the red stripes are fake there's a
little bit of flaking in the blue but
we're not really going to worry about
that
the game over also read
and then the one
two
three
and four are all red so there's not a
ton
that has to be done but if we could get
that looking better it would make it
look much better now that cable thing
has faded
to where it's almost orange
or maybe it was orange I'll look at a
picture of another one just to make sure
I guess it probably was orange because
the Red's right there beside it and it's
not faded so orange but we've got one
the 76 part definitely needs it
and the one two three and four
definitely need it that would make this
glass look a lot better
so we're gonna do that there's also a
little spot there we can hit at the same
time and the game over
so I'm going to try to find a color
that's pretty close to that
and we'll go ahead and and make it
happen
very cool I'm going to look at a picture
too just to make sure
that that's red maybe an orange it looks
a little light but it could just be
playing tricks on my eyes
oh yeah it's the same as the flag
which you know obviously would have been
red okay so I need to find a red that
matches this other red here pretty well
and then we'll go with that
so I've got a whole bunch of different
colors but this red alert
seemed the most similar
to the red on this back glass
this stuff's like a dollar
it used to be 69 cents but inflation
happened and now it's five dollars and
fifty cents I think maybe not that much
but it's close
so I do this a little different than
most people if the best way to do this
would be to airbrush it
so if you're good with an airbrush that
would be good I I do it right here in
the front room of my storefront
and you know
I'm not hooking up an airbrush and using
it in here it's just I'm not gonna do it
I'm not interested in doing it the
perfect way
um so I you know I'm just trying to help
the guy out make it look better
so the problem with red in particular in
any color on a back glass is that light
is literally shining through it this
part that's gray is a mask light won't
shine through that but all of this is
illuminated
all of that all four of those numbers
that that all this all of that is uh
translucent not transparent translucent
so and this part is opaque
so you're trying to match translucent
areas with opaque areas anyway it's not
the easiest thing in the world and then
plus you have some of the original paint
still on there
so for instance I haven't done this
orange thing yet if I paint that in like
I painted these in
you will see all of the areas with the
original paint will be darker than the
areas with the new paint because they're
one thicker coat of paint
on that so whenever that lights up
you're going to see every little area
that has fresh paint on it
so you could try to just paint the area
that's chipped off but look at that
how the hell are you gonna do that and
then you'd have to have a perfect match
on the paint
you chasing your tail it's not worth
even attempting right you could try to
to cut off the old paint so you could
take an X-Acto Knife and very carefully
make a score and take all the old paint
off and get that perfectly clear and
then paint it but
that's a lot of work you know that's a
lot of work for a back glass that's kind
of meh it's not original
has areas you've repainted
if you were to airbrush it it would look
much more smooth but you would still see
the areas that have an extra layer of
paint that have the original paint those
areas would illuminate darker than the
areas with the fresh paint
so the best way I've found to do this is
the way I've done here now another thing
is red paint is notoriously thin paint
it doesn't have a ton of pigment in it
it's not really dark right
so if I take a paintbrush
and I was to paint one coat of paint on
that it's going to go on so thin that
you're to get it to the level that it's
printed on the glass or silk screened on
the glass you're going to have to put
like eight coats on it takes forever
so that's not how I do it anymore what I
do is I glob that stuff on there so it
is on thick as crap
and it's kind of lumpy
and kind of there's Globs of it if you
don't do it that way though what happens
is you got to put eight coats and then
you see all of the brush Strokes anyways
it's just not worth the trouble so what
I've done is I've as carefully as I
could painted the lines back what do you
think it's fairly straight
now you don't have to color within the
lines on most of it so that four there
for instance since the masking all
around it is blocking everything I mean
I could paint this whole area red and
you wouldn't be able to tell the only
part you would be able to tell is where
the four is where it shows through
where they left the masking off so that
it would be translucent
right so you don't have to do that
this particular one so these are it's so
thick that they may not even illuminate
anymore but you'll see the one the two
the three and the four very nicely and
they'll be nice and red on the front
look a heck a lot better than it did but
they may not light up on this particular
game it doesn't really matter because
the entire score Windows light up as we
did earlier where it says game over
though you wanna you need it to be a
little thinner if you can help it I
still had to go pretty thick on it to
cover all of the Screwed Up spots but
that needs to kind of illuminate so you
can read game over
so you don't want the paint an inch
thick so I went with half an inch thick
so hopefully the light will still shine
through it a little less a little more
than it will shine through this area and
you'll be able to read it
the
76 Stripes there
I just as carefully as I could paint it
only the red parts
um
and I think it'll look decent
that was just a spot it was scraped so I
need to do this orange here I've got to
mix it just a little bit
I believe it's a combination of
Canyon Orange
and
deep ogre somewhere in the middle of
those two is about that color so I'll do
the best I can to match it and then
we'll see what it looks like on the
other side
all right so I took the Deep poker I
poured a little bit of it in the cap a
little too much of it in the cap and put
a little bit of orange in it to Orange
it up a little bit
painted the little strip thing and then
his suspenders or his leather whatever's
were pretty bad so I went ahead and did
them too
so two colors now that's not every
little piece that's messed up on it but
you know you got to know when to stop
maybe I should have already stopped
right
so
the one looks pretty good the two looks
good
the three looks good but if you get
really close
see how it's splotchy so that's how it's
going to light up it's not going to be
perfect
and the four that looks much better the
76 much better
I mean much better
here's the little cord thing whatever it
is
pretty close match
and his suspenders look pretty good
so there's still problems all over the
place like there's this
there's some red there too that's you're
going to be able to see through I saw
like a
you know piece of the white is messed up
so this is not going to look perfect but
it'll look more presentable and when
it's sitting there turned off which is
most of the time that people own a
pinball machine it's just sitting there
turned off at least they can read the
spirit of 76. uh good old red white and
blue old school red white and blue too
um so it'll look very presentable the
one the two the three and the four look
really good it'll look nice in the back
glass even when it's turned off so I
think that uh I think the customer will
appreciate that oh and the best part
about using this acrylic paint and uh
putting the triple thick on it before we
do it is if you don't like it you can
just wipe it right off
all right folks I'll show you that here
in a second how that all came out it
looks decent looks pretty good I think
but we're going to test play it a little
bit what do you think about that
I just saw something weird on the back
glass we'll talk about that in a minute
so I think we're about done with it
you know they play a lot better with the
glass on them if
try that sometime play one without the
glass on it then put the glass on it see
if you think it plays better
they really do no joke
[Music]
[Music]
nice is that a little backhand
I missed that one but I got the other
one
oh no
there we go you want to get that c
because the only way you can get it is
at the top
[Music]
whoop missed it
now probably a little better if I
bounced it a little bit what do you call
it
nudged it if I nudged it a little bit
but uh
the camera's in the way folks
I can't nudge it with the camera in the
way
I'm sacrificing for you folks
give me my C oh I missed it
well she plays pretty good
I believe the customer will be very
happy
[Music]
double bonus when lit
[Music]
there's kind of a Rhapsody to the charms
[Music]
all right so y'all can spot the light
that's out
we're gonna play it one more time now it
knocked because I don't know why it
knocked
maybe I got a high enough score
uh yeah okay so let's play it again one
more time
come on Big Money big money
nothing
110 points
still 10 points
I haven't made the saucer shot yet there
we go see it works
oh I was playing with it too much
foreign
well I think we saved it
this is a very playable very presentable
game
just needed a little attention and
that's all
[Music]
um
what a cool game
come on
I hit it four times and never got it off
the flippers
[Music]
all right well very cool I see a light
bulb out
but other than that everything's working
pretty good
and this is how the back glass turned
out now this is with all the lights on
obviously and I mean the lights out
so I don't know how over blown that will
be on the uh
camera there but it looks pretty
freaking good
this almost looks like it's supposed to
be like that because the blue is faded
remember I cleared it all too so it's
not gonna get any worse but the blue is
faded
and the red that I painted back in has a
kind of similar look it's not quite
straight but yeah it kind of looks like
it's not supposed to be so one of the
weird thing I was saying that I noticed
on the back glasses
look how they've got it where half of
the guy is covered up I don't get that
there's nothing back there
they painted it like that
so I guess he's just supposed to be in a
shadow
but that's how they did it
the guys
leather straps there turned out pretty
good
and then maybe best of all is the one
two three and four all came out pretty
good
probably all
blur it's probably all bleached out
but yeah I think it looks great now on
this particular one it looks like that
they did want the game over light to be
the one that flashes on a lot of games
behind where the title of the game is
flashes but it looks like the way this
one was designed
um
just the way the the bulb holders are it
looks like it was supposed to be the
game overlay so I think we're I think
we're pretty good nice little game very
fun great theme obviously
um very cool so there you go hope you
enjoyed it I enjoyed working on it I
hope the customer enjoys it make sure to
give us a thumbs up for taking the
trouble to film it for you
if you haven't subscribed please do and
make sure to check out my brother's
Channel my brother Donnie has his own
channel here on YouTube I help him with
that I'm over there on his channel a lot
he was just by here a little bit earlier
today and we work on arcade games
pinball machines and jukeboxes my
brother Donnie works on Old Vehicles old
buildings things like that and fun time
is had by all over on his channel so go
check it out so I hope you enjoyed it we
will see you on the next video here in a
couple days we'll start another series
on another machine so we'll see you then