This Bally Lost World Pinball Machine Had The Backbox Lamp Board From Another Game! So none of the lights or the displays would line up. We made a new one from scratch...
Thank you to everyone who has been supporting our channel! If you use the link below before you purchase anything on Amazon, we get a royalty for sending you there, thank you!
Our store is located at 139 Caldwell St., Rock Hill, SC 29730.
ladies and gentlemen this is Joe's
classic video games back with another
cool pinball repair video for you this
evening we have been working on this B
Lost World pinball machine and we've
done all kinds of stuff to it if you
didn't see our Series so far go back and
watch them but if you watch the earlier
um videos then you know that the head on
this thing is not actually a b head
that's actually the head off of a um SE
stingray a Stern
Stingray um we just happened to have the
body of a lost world and it didn't have
the head and then we had the head of a
stingray that didn't have the body so we
put the two together and we were since
we put new art on it and everything you
can't really tell but the main problem
is that the lamp board in the back is
all wrong everything's in the wrong spot
so um one of the things that they would
change whenever they made new machines
was um the layout of the displays on the
artwork and then also where the lamps
are that the computer lights up so we're
going to take this lamp board and kind
of turn it into the correct one um so
Joey has cut us a new piece of wood here
for it out of 3/4 inch plywood and
so we're going to modify that with
pieces from this like maybe some of
those light baffles and some
measurements from this and blah blah
blah blah blah and I found some pictures
online line of how the lost world one is
laid out and we have a back
glass um that we can tell how
everything's laid out from so that's
what we're going to do in this video so
stay tuned so I think the first thing
I'm going to do maybe is remove that one
or maybe I'll I'll put up the
replacement back glass that we've got on
that one and you can see the difference
in the layout so our replacement glass
is going to be one of these translate
things that they make um we got a pretty
good deal
of course we'll have to have a sheet of
glass in front of it but you can see
that the score windows are nowhere near
the right
spot um the stuff doesn't light up right
although the game over light is lit that
may actually be the correct one this one
almost lines up uh the Tilt is lit I
don't know what that one would be same
player shoots again is
lit um so we've got a bunch of we've got
a bunch of stuff lit up that's not
supposed to be lit up because
everything's in the ABS absolute wrong
place so with that said I'm going to go
ahead and remove that board and then
we're going to use it and pieces off of
it maybe if we can get those light
buffles off to lay out ours just like
this back glass so that we can get it uh
how it's supposed to be but the the
trick is no one really knows what it
looks like behind the back glass so you
don't have to be perfect everything's
just got to kind of be in the right spot
well on second thought after looking at
all the wiring it's it's actually going
to be kind of hard to remove the thing
without unsoldering all the wires it
doesn't just unplug so we're going to
leave it in for the time being but the
first thing I did was compare the size
of our replacement one with the old one
and it's pretty much the same slight
difference but nothing
major um and we're going to measure off
the back
glass and on this particular cabinet the
way it's mounted there is exactly one
inch from the side of where the back
glass mounts to where the wood starts so
if we figure out how much extra room is
on each side of the back glass that we
have we should be able to lay it out
where whenever it's centered
everything's lined up so that's what
we're going to run for and I've got
pictures of How It's laid
out um that I got off the internet too
so that'll help so we get we've got an
extra inch on the side of the back piece
here that allows room for the back glass
so let's measure the back glass compared
to the opening that we have here all
right so after measuring the space here
is 28 and 3/4 of an inch is the room for
the back glass a real back glass that
we've got a u b Night Rider over
there is about 28 and a/4 inch the
translate that they sent us is less than
28
in so typical reproduction stuff that
sucks I don't like anything reproduction
always problems right so uh 20 28 and
3/4 in and the thing we're putting in
here is a little less than 28 but
whatever um so we need to keep that in
mind as we lay it out so that we can
Center it properly u in the back box so
I'm going to write that down so we can
base all of our measurements off of that
all right so I took tons of measurements
I'll read them to you so this in case
you need to do it you just read my
handwriting you can probably read it but
I'll read it for you okay so there's one
inch the pin was running out of ink
there's one inch extra to the left off
of the board you got to keep that in
mind there's an 18 and there's a 28 and
3/4 in opening but the translight is
only 28 in so there's an extra 38 Ines
to each side and one of those inches is
wood though so you have to subtract 5/8
from whatever measurement you get on the
translate if you're talking left or
right okay the wood starts 5/8 inch off
the bottom of where the transl light
will sit because the transl light's
going to sit in a little Channel you
know so it sits five 5/8 in off the
bottom of where the translite will sit
you so you got to subtract 5/8 of an
inch off of whatever the measurements on
the translite are because it extends
past the wood that much okay so the
first windows are 3 and 1/2 in off the
left but that's the window that's not
the actual mounting hole right and and 5
1/2 in wide but the displays are 5 in
wide which you can see so you want to
you want to Center them in that viewable
window but the cutouts are 6 in wide so
I came up with that the measurement
should be 2 and 5/8 of an inch off of
the left side and 8 and 5/8 of an inch
uh uh would be the end of the uh the
cutouts okay now the the second windows
are 19 Ines off the left which means
that it would be 18 and E and 24 and 1
eigh is where my lines need to be and
then the credit cutout you know it's
offset a little bit so it's 28 it's 20
in off the left which means that the
cutout should be 19 and 38 and 25 and 38
which should be where the two lines are
now the bottom windows are four and 3/4
of an inch off of the bottom the windows
are that you can see uh in the translite
are an inch and a/ qu in tall the
viewable score though is only 1 in tall
so you need to center it in that so 1
and 1/2 in below uh the viewable display
is where the cutout starts and the
cutout is 3 and8 inch tall so I got from
that that uh you should be 2 and 3/4 in
from the bottom uh and 5 and 78 in from
the bottom now you'll notice the
measurement was 4 and 3/4 but I made it
2 and 3/4 so basically you subtract 2 in
off wherever the measurement is on the
translate then I had to turn over the
back the credit window is 13 and 38 of
an inch from the bottom and then I've
subtracted the 4 and 3/4 in that the
window from the on the bottom ones was
just so I can make sure that it all
lined up and what I eventually came up
with was that if you subtract 2 in off
13 and 38 you uh your hole needs to be
cut out at 11 and 38 and then it will
run to 14 and 1 12 because they're all 3
and 1 e in tall okay and then the top
scores are 18 in they made gave me a
round one nice square one uh which means
means that the cutouts need to be 16 in
and then another line at 19 and an8 so
it all makes perfect sense if you think
about it so this is what I came up with
I drew the five boxes in I think that's
where they need to go so I'm going to
lay the transl light up on it and see if
it looks correct if you look at the left
and right centering looks like we're
about right I mean I measured it so it
should be right right and there's a
little bit of an adjustment in there
those little those little metal plates
you can move left and right a little bit
if you have to so I think we've got the
left and right proper let's see if we
can tell on the up and down so it also
looks correct you can see that it's kind
of centered in the top part of the
hole and all three of them are in about
the same spot so I think we're I think
we're pretty good you can see that the
display the viewable part um is at about
the halfway a little bit above the
halfway mark of the hole the whole
middle would be about right here so I
think we're lined up
all right so I found a pretty good
picture of one online um lit up with the
back glass off of it so I was able to
just kind of tell where everything goes
so everywhere there's a circle in an X
is where there's going to be a hole for
a lamp
socket and uh I'm going to use
the little baffles off of here we're
just going to cut those off and then
staple them screw them whatever to the
new one in the appropriate place
basically the the ball and player down
here and then this is same player shoots
again this is tilt this is game over
four player three player two player one
player um one player two player three
player four player um this is maybe
that's same no that's high score to date
um and then the other ones are just the
general illumination so they don't have
to be perfect but in
general get it in general they should
line up with the artwork a little bit so
I looked at the the one online that I
had a picture of and then I just kind of
freehanded those in so those are
probably not exact but they're pretty
close to exactly how they are on the
official one and then on the official
one the corners are chopped
off and the reason for that is because
down here there is some
blocking that can be in the way you can
see on the stern they're a little bit
chopped off
and up here you have to have some room
for the um the lock and the the lock
mechanism up
here but on the balys they're diagonal
so I just made them diagonal like the B
because that's what we're trying to
make and the other thing too is that the
hinge mounts slightly different on a b
it's on the front
here but on a Stern it's actually on the
back so that hinge does screw onto the
back but it's where you can't see it
um and of course this isn't ours this
little block here will be right here on
ours ball one two three four the
measurement is the same on the Sterns
and the
um B so that must have been kind of
standardized for whatever reason so
that's that so I'm going to have Joe cut
out the five score windows and then uh
drill all of the holes four 5 6 7 8 8 9
10 11 12 13 14 15 16 17 18 19 20 21 22
23 24 25 26 27 28 29 30 31 32 33 34 35
36 37 38 39 40 41 42 43 44 45 46
something like 48 of them maybe 50 of
them
um so once we get that we'll have the
board how it needs to be then we can
start populating it with wire and um all
those freaking sockets I'm going to
reuse most of the ones out of this um
sewitch I me
Stingray um backboard just to make it
simple they they clean up pretty good um
but that that's going to be a
considerable amount of effort
[Music]
no
[Music]
[Music]
oh
[Music]
[Music]
[Music]
[Music]
okay so Joey cut it out and drilled all
the holes this is what we're starting
with we put some white paint on it
here's the one that I removed from the
game um the next thing that we need to
do is install all of the sockets which
is a pain but it's not going to be that
bad there's only what we say 50 of them
it won't be that big of a deal folks
that's the
back it's the back of
theirs I'm going to take this one and
see if I can just remove all of this I'm
going to unsolder each socket and pry
the Staples out and see if maybe I can
even save the um the
um the lines there so we can use
them in ours so let's see all right so I
was able to pull out all of the Staples
and remove all of the sockets and the
wiring so we've got everything off of
the old one now we need to transplant it
appropriately onto the new one I have a
picture of the back of a Lost
World um setup so that I kind of know
kind of how they ran the wiring On It
originally all right so we did something
similar on that Eight Ball deluxe uh
series that we did a while back
basically I'm going through putting the
socket in uh and then running the wire
over it and then stapling it in a lot of
places so it holds it all in place and
then you solder the wire to each thing
easy peasy now see how all of these are
linked together that's because on the
very bottom of the board each one of
those is a computer controlled lamp so
on this back box on this backboard
you're going to have two types of Lights
the ones that the computer can turn on
and off and you're going to have ones
that are just general illumination
they're always on so the ones that are
General illumination are all going to be
hooked together and so there is going to
be a line on one side that connects them
all together and a line on the other
side that connects them all together and
that'll run you know halfhazard around
and go to all of the ones that are
General illumination but the ones that
need to turn on or off uh are wired
completely differently they have a
different wire for the ground or
whatever the one side of it right and so
that's that has to be separate from your
general illumination Loom so I'm
basically putting those in right now
with this it's just then going to come
up here and grab a couple more like uh
these turn on and off those turn on and
off um that one turns on and off that
one turns on and off that one turns on
and off that one turns on and off those
turn on and off so it's it's not as easy
as it looks
you at the factory they had jigs set up
where they could just run through it and
make them really quick but we don't have
that luxury so I got to kind of take it
slow to make sure that I'm not
connecting the general illumination
light bus to the um the switched
illumination light bus so there two
wires to make the general illuminations
one stay on and then there's one wire
that's the ground for all of the
switched illumination that's different
than those two for the general
illumination and then each one that
needs to the computer needs to turn on
is going to have its own wire running to
it blah blah blah so I'll show you more
as I go through but so that's my very
first part I got all of those in at the
bottom uh so now I'm going to work my
way up of course okay so we're upside
down now so the way it is on the picture
that I've got the so these are all the
the computer controlled ones so one side
has to go to a common like a a voltage
right so it comes around here grabs this
one snakes through here grabs both of
these and then comes all the way up here
to get this uh high score to date one
all right now now there is a this one
this one this one and this one uh get
individual wires now these two there is
a wire that connects between them so I
got to get one of them and stake it
through here all right and then these
are General illumination so they all are
just Daisy chained together basically in
uh uh
parallel got tricky
here right and so that's the top half of
the board so on the bottom half the same
thing goes on basically that same type
of thing happens uh where it comes up
over here down here
there uh and then goes this way and one
has to go down here as well one has to
go down to here you know so it it just
snakes around all over the place it
almost looks like a little train TR
train track or something but I'm out of
wire so I got to find my wire oh here it
is so I'm going to use that now too so
this stuff is stranded I found this at
the flea market they also sell it at
Lowe's and stuff they probably sell
stranded but I just didn't see any but
um this is just
um like um uh they call it utility wire
I don't think it's galvanized but I
didn't have any kind of problem
soldering to it so I think it's going to
work perfect for what I'm
doing all right so
here these two have to be connected
together and snaked it in there you got
to make sure sure none of your Staples
are ever going to touch and then it
starts down here and it goes around and
it grabs all of this and it grabs that
but not that and it goes this way and
that and it grabs that but not that and
that way and that way and that way and
that way and that way and that way and
that way but then it doesn't get that it
goes down to here and then through here
and over to here so you know we got her
going now the hardest part is getting
those lines to be
straight if you took more time doing it
you could probably do it but to me it's
not that important and plus it's
obviously homemade so now it looks
homemade so you know I'll just be proud
that I made it okay so uh I'm actually
one socket short it was a we needed a
few extras for this compared to the uh
Stingray uh and I put all the old ones
in there and then I put all the new ones
that I had in there as well um but I'm
just a couple short and one short one
socket short so I'll have to order some
but basically we've got all of the hard
part done so now I need to mount it in
the
machine um and we'll work on it actually
mounted in the game so that we can make
sure everything's lined up and displays
are right and blah blah blah but it's
going to take a little bit of time to
hook the um to hook the wiring back in
because some of the wiring is not going
to be in the right spot I think I'll be
all right on the displays or I hope I
will but the uh some of the the wiring
for the the general illumination lights
I mean not the general illumination the
the CPU controlled lamps are going to be
in the wrong spot just because on this
game it's here and on that game it's
there but
um this is what we ended up with after
stapling all of the uh the line on all
right so the utility wire soldered just
perfectly I don't I don't know like I
said if it's galvanized or not so want
to look for that at the hardware store
um I'm using this Arrow electric stapler
this thing worked great for it this is
plywood so it's fairly soft anyway Pine
Plywood And then I've been using a quar
inch staples which are pretty much the
size of the ones that I took out of the
stern um uh lamp board
so I'm pretty sure they're a quarter
inch too uh and they work great so
that's what you want to do if you end up
having to do this you
yourself all right I was able to mount
it in there I got it as low as I could
to where it's not quite dragging the
other one was dragging it's it's pretty
common for them to drag on
this so it swings open on its own just a
little
bit that's all right with
me and I ran the wiring harness similar
to how they had it on the other one
so on the other one down here these
ended up under the displays the displays
were about right here okay and so on the
other one the 1 two 3 4 player were
right here but it was enough to stretch
it down
here um and then there was also a
connection for the GI bulbs I was able
to put them connect that there to that
socket now since it's connected to that
socket it's connected to everything that
those lines are connected to
all the way over to
here all right and then this one is the
Tilt it lined up pretty good this one is
the game over it lined up pretty
good uh this is player three up and this
is player four
up this one here is kind of a strange
one it's just one bulb that's a general
illumination that just happens to be a
way where they couldn't get wires to it
so they ran specific wires to it and and
the way it all laid out I had two extra
wires here that I was able to do the
same thing so that worked out this is
the
[Music]
match I think that's the Tilt that's the
match this is the ball in
play this is player
two this is player one and then this
wire in the middle is this blue wire to
power the other side of it um that blue
wire also is connected
here so that it Powers all the other
ones all the way
down um so the top General
illumination there were a red and white
wire here they could power
that and then the only one that I really
had trouble with was up here is the uh
high score to
date it just wasn't long enough so I
extended the wire a little bit you got
that working so we've got them all wired
up the only there was another problem
these two here are actually the uh same
player shoots again on some games that's
shown on the back box on some games
that's shown on the Playfield on some
games it shows at both places on uh um
Stingray it shows it on the Playfield
there's a light on the Playfield that
lights up but on Lost World it shows it
on the back box so we had to run an
extra wire into the harness to make sure
that's
um wired up so after all that's done I
took the multimeter and I checked
between the two wires that are running
all of the general illumination bus just
to make sure they weren't shorted
together if you check that while it's
plugged into the power supply it will be
shorted together because the power
supply is also connected to the
Playfield and so the lamps are pretty
much a short so once you have you know
40 lamps in parallel it's going to
measure like you know 1 ohm resistance
between the
two um
sides of the general illumination bus
but since I unplugged a power supply
they're not connected so that tells me
that there's not a short on any of those
sockets same thing with the one on the
top none of them are connected so
there's no short on any of those sockets
I didn't check every single one of the
um the computer controlled ones if you
have a short on one of those sockets
what it'll do is it'll burn up the CR on
the board that runs it but it won't
cause you catastrophic problems where
it's blowing fuses and stuff like that
so if we end up where One of the um one
of the lamps doesn't work we'll
troubleshoot that but we got all that
done so we're ready now
to put all the light bulbs back in it
and uh see if it'll light them
up all right folks so I got the piece of
glass in and was able to put the artwork
behind the glass it all looks pretty
good I got all the light
uh in and
working and I got the LED displays lined
up properly so everything's pretty good
the only thing we haven't done yet is
put the light baffles in that tell it
not to light up this part only light up
this part so for instance if you look up
here you can see how whenever that comes
on it's pretty readable and it you can't
really read it whenever it's um whenever
it's off so that's good but but all the
other ones are kind of bleeding over
like it looks like the four is lit up a
little bit right now the same player
shoots again you can see lit up a little
bit it's because it's supposed to have
those things around it to make it where
it it only lights up that area so uh we
need to install those so we need to cut
them off the old insert and install them
on this new insert and that will
basically block the light in the correct
places this one that says ball and play
I'm not so sure if that's supposed to be
lit up right but
maybe um and I think we're one short
because we didn't have one for this same
player shoots again or something like
that but the one up here for High game
to date it doesn't really need it it's
nice and dark whenever it's off so we
don't need one up there but we need it
on all the other ones so we need it for
game over match ball and play one two
three and
four same player shoots again tilt and
then one two three and four you can see
they're kind of lit up right now like
two is kind of lit up so we got to
install all of that the art came out
pretty decent though it looks pretty
pretty
good everything's lined up pretty well
so at least you can see the uh the
displays so far so if we can get those
lights to look a little bit better and
be a little bit more where they're
supposed to be we'll be looking be
looking
pretty all right folks so we took a um
multi oscillator tool oscillating
multi-tool uh that we use on all kinds
of stuff and cut those little things off
the old board and then put them in the
appropriate spot on this
one uh the one up here where it says
High game to date it's so far away from
this one that on the back glass it
doesn't need to really be isolated and
then the same thing with this one down
here which is tilt but this one is same
player shoots again this one's game over
this is one two three four this is three
four one two and all you got to you're
just trying to keep
that area of the back glass from having
light seep into it so that whenever it
lights up that bulb is all that's
lighting it up but we kind of got a
thing where they're a little bit off
because we made the thing from scratch
right this is I think match and that
one's ball and play or something um but
we got them all on there the like I said
the only one that's missing is tilt
which it see how far away from the other
lamp it is you don't really need it and
then the same thing up here so I think
that's going to work so I took the back
glass and I finally got a piece of glass
cut it took them four weeks to cut a
piece of glass it's just they've been
way
behind um and I carefully attached the
transl light to the glass cleaned up the
channel down there on the bottom and put
it back in um put it back on
it and uh I guess we'll slide it up in
there and see how it all lights up so we
I think we've just about recreated the
backboard which was in my opinion going
to be the hardest part of the whole
thing all right so you can see what I
mean about the
Tilt
right and the High game to
date you can see that the one two three
and four are not illuminated we' blocked
the light out of them pretty good the
game over is nice and bold where you can
read it
well same thing with the ball and
play all right so I'm going to put it in
test
mode so we can see if they all light up
how they
should you see the high game the date
the one and the two are working
perfectly the three and the four are
working perfect
L the 1 two 3
4 are now dark and light dark and light
like they should be same player shoots
again you see what I mean with the Tilt
the game
over the match ball in play so now it
can properly communicate everything that
it's supposed to say very cool so we're
getting there well we have one video
left we have to do the sound board so we
have to our our we got a soundboard from
our buddy GTO if you don't know about
him he makes reproduction soundboards
for these things for all kinds of games
so we've got one of those we're going to
pop in this baby so that it can finally
talk to us so we'll do that on the next
video I hope you've enjoyed it so far
hey if you like these old B videos check
this one out that we did a while back I
think you'll enjoy it as well see you on
the next one