827. Using Patented Rulers and Spinner/Disc to Trim a High-footed Bowl with Hsin-Chuen Lin 林新春 修坯示範

Hsinchuen Lin
205 followers
3 Video Views·Nov 13, 2024
To see or buy my finished work and pottery tools, please visit my Online shops:
https://sawfish-endive-kgks.squarespace.com/shop
http://www.etsy.com/shop/hsinchuen
http://www.etsy.com/shop/hsinceramics
http://www.etsy.com/shop/hsintools
To watch more of my YouTube videos, please visit my channel:
http://www.youtube.com/@hsinchuen
To learn more information, please visit my Website:
www.mypots.net
Instagram: @hsinchuenlin
Facebook page: Hsin-Chuen Lin Ceramics
Pinterest: @hsinchuen6518
all right today I'm going to trim this
very tall foot I intentionally leave the
foot
slightly thicker so when I trim I can
leave a very tall foot on the
bottom and also I like to introduce
several of my tools that is very good
for doing the decoration and for
trimming I have showed you this uh in my
previous video to check the thickness of
the bottom before you trim so it will be
more accurate when you're leaving the a
clay on the bottom especially the very
tall foot it's very hard to check the
the correct
thickness so using this measuring tool
is very easy so what I do is check the
inner part of the dep and then from the
top of rouer you check all the way down
to the bottom so that is
how I check it and uh there's a gauge
the the rot there in millimeters so on
the inside is
71 and on the outside is 90 okay so 90
minus 71 is 19 19 mm so it's fairly
thick and I intentionally uh I will lift
the inner part of the fing within 3 mm
so that means I could go 16 mm deep and
I will check it I dig a hole in in the
center and I keep on using
my router to check the depth of 160 mm
and then I will
stop and also this bet okay this I call
this translucent bet uh it's also good
for trimming because I have a small
gap of the
circles and uh using the circle it will
help you to find your Center easier
especially the very smaller
capap looks fairly close on the distance
from the
circle okay and you can see that without
tap centering or without checking it as
long as your bow is very uniform you
should be able to find your Center
easier
and then you you could uh use water
actually this me to use water and use
the water or slip it will stick on there
but I'm going to show you uh my other
tool that uh it's also good tool after
you remove your holding clay you can
trim all the way down to the base down
to the
corner but for now I'm just using the
clay coil to hold the corner here
and this is one of the tool I designed
it it's uh actually I call this number
two because it's a like rectangle shape
number two triming tool and I have
different materials standless steel and
the high carbon standing steel and tunon
carai and this one is ton
carai once you are you are using the
tons Cara it's hard to go back to the
regular one because this whole the sharp
edge much much longer very very long
without needing it to resharpen
it so I roughly
trim the outer part of uh of the
fine to approximate the size
okay and then I will start to dig
inside of the
fine
um to remove the clay that I don't need
it so I usually use the corner of my
tool to give myself a guide guid line
here so this is the part that I will re
remove it
so this this triming tool the number two
all the edges has been beveled so they
are o sh and you can use all the edges
to do your
trimming so you can flip it can turn
your
tool or you can use the the very top
part of the tool
so after dig it in I will check see how
far I can
go so I can bring back
my measuring to or there's a slot in the
center so you can can check
it and now I have about
14 okay if you cannot see it clearly you
can hold it hold it and
then bring it closer to
you okay you can hold it like that and
then bring it to
you so 14 is almost there so I will just
clean it up finish up maybe a trim
couple more millimeters two more
millimet and then I will
stop the the good thing for this tool is
that this is sharp 90° so you can get
your inside corner a very sharp
90° if you prefer that
way right I will do my final check in
and to see if that's right I think it's
about 16 mm
so I will stop right here and uh clean
up I did not uh remove any clay from
this part here because I need to use
that to gauge and I will do I will level
this part here at the very last
right so that width of the footprint is
good and the depth is good and now I
will compare the inner part of outer
part of the ball and the outer part
could be slightly low since when you're
making the bow the inside has a little
curve so the outer Corner could be
slightly lower than inner corner
all right so this is my number
two triming tool and uh when you see I'm
doing the very heavy lifting meaning I'm
cutting the thicker deeper I using this
method to remove it but I hold my tool
slightly more like 90° angle but when
I'm doing the very final the very last
stage to just kind of burnish the
service I'm holding my to slightly
angled this angle so this part here
to touch the surface of the clay and
then you can have the burnish effect so
that surface will be smoother if you're
holding the tool like this way you're
kind of scraping it when you scraping
you won't be able to cut it smoothly so
that's the technique of how you when by
the very last stage just trim a little
bit and hold your hold the angle of your
to slightly DET tiled so the the pebble
side of the tool could touch the service
meaning you're cutting it but you still
burnish it and your service will be
smoother okay so that's the uh number
two tment tool and now I'm going to
introduce my new updated the plastic
glass uh the spinner
combination so this is the the newly
updated tools
this one slightly thicker than my older
ones let me show you my older ones so
this was this is 3 mm and this one is 4
mm 1 mm
thicker and I also have it since it's
thicker so I can have it deeper so the
spinner could sit inside the slot more
secure without falling off while you're
transmitted okay
and also for the uh decoration
Mark I put it into colors and the three
or more holes so you can use the hole to
just punch it through use the needle to
and punch through the holes without uh
using my old meod just go underneath
here you can just go straight straight
down okay straight
down so older one the newer
one and it's more C 4 too so it's easy
for you to
see the uh Division and also have a mark
is little bit small but uh you can still
see it okay so in case you need to find
your division this is very good tool and
I will I will show you the division too
okay but for this me for compressing it
first you put it
on you find your Center using the the
little
bit the
circle
and you find your Center much easier
because again that the Gap is 5 mm apart
so it's close it's easier to find your
Center more accurate and just drop in
drop in your aluminum spinner and hold
it down here you see that you're holding
holding it down hold down your spinner
so you have D
pressure and after you remove your clay
from the
corner the Dum pressure will hold your
part in position and you can trim it all
the way
down okay so that's what the spinner are
all about because when I'm
trimming I slightly have a little curve
here so if you are using this
directly it's it's rocking and also when
you trim this part here might be sof so
if you have a pressure here you might
ruin your inner part of your uh foot
ring so versus this one is sitting right
on your foot okay right on the foot so
it it's stronger and also it's
leveled okay hold it down and then trim
it
okay so I connect the curve most
smoothly all the way down to the corner
and again I have two
sizes if your foot is not uh not too big
and you could probably use the smaller
one
too and again hold it down and you can
trim all the way to the
corner okay so that this is what uh one
of the function for the dis it all is
all about
this is my older version and this is my
newer
version it's very tall foot
[Music]
[Music]
