Land Rover Range Rover Evoque 2.0 Blocked DPF Cleaning & Adblue Nox Exceedance

AutoTuned TV
1 follower
1 Video View·Dec 17, 2023
P2463-00 DPF Soot Accumulation and P2BAE-00 Nox Exceedance
for repair bookings email [email protected]
Launch UK products used in the video are available at www.launchtech.co.uk
[Music]
hello Jimmy here Wellies I have a Range
Rover evogue here uh 2016 2 L
engenium okay on the dashboard we have a
DPF full sign engine management lights
on going to use the launch Euro Tab 3 do
a highspeed
scan
see what fults we have front left
camera
ECM DPF blockage s accumulation nox
exceedence from the ad blue uh vehicle
conditions incorrect for particle filter
regeneration then we have a
p0672 glow plug cylinder 2 circuit open
okay so if we come down into the engine
bay here underneath the intake
manifold so I come down can see you got
a glow plug there and I've already
taken the plug off of clo plug number
two which is right there I can't
actually see these but I can get the
camera down here of course I can just
about get your hand down there can't
really see what I'm doing but we've got
it
uh going to
use size 10
mm uh this is a glow plug kit from Omega
we get that down onto the glow plug down
there okay so we' got the glow plug of
the cylinder 2 now depending on what the
customer wants to do we can change just
a single one or we can change all four
so obviously advisable to change all
forward glow plugs at the same time if
we look at the tip of that you can see
there's a great big hole burned in
[Music]
us okay I've got a delivery here from
Bennetts get some new glow plugs okay so
if we look at these replacement glow
plugs this is what it should look
like nice and
clean okay we've got the glow plug in
there t
down and we can just get that out
so that's it now we've got the connector
plug back up we can come back
out okay so for now I've just replaced
the one glow plug we'll have a chat with
the customer in a minute if he wants to
do all four now what I will explain here
is discode vehicle conditions incorrect
uh that is why the DPF has stopped
regenerating itself and that's why the
DPF is blocked up and the cause for the
incorrect condition is the glow plug on
cylinder 2 which is this part right here
uh so when this part has failed the DPF
regeneration process stops and then your
DPF just gets blocked as you drive it so
now that we've got this in we can clean
the DPF and reset everything and he can
be on his way so next thing we're doing
customer going to go grab some ad blue
while I'm going through the rest of the
system we're going to top up the ad blue
of course he's also got a message on
here saying that the ad Blue's
low if we go through it well
go back we did have a message
there we got the one about the DPF full
B open I did have a message saying there
was low ad blue it's not showing up
right now so when you get a low ad blue
on these as well that'll set off this
nox exceedence code again which will
stop the DPF regenerating so make sure
you don't let the ad blue go empty once
it goes down to a certain level it'll
set off this code and just topping it up
on its own will not clear this code you
have to then get it reset so it's a lot
better to just keep your ad blue topped
up then let it run out and then you get
set off with this code here so once we
top the ad blue up we can just clear
that code and it won't come back now if
we go to data stream and we search for
the differential
pressure I've already take
this we have 50 m of pressure which is
quite high for one of these and if we
hold the rivs up 3,000 RPM we have
320 M of
pressure okay so I'm underneath the car
now this is the ad blue injector I can
see someone's already done some sort of
repair on the wire in there so I'm going
to
open these bolts on a little crossmember
here just so I
can get this down I'll show you now we
can just move that to the side because
I've loosen the bolts on the other side
as well there now just gives me a little
bit of easier access to the ad blue
injector so I'm just opening this clamp
here with a size 4 hex key we got that
out okay so I've removed that we've got
the clamp off and what can happen with
these is the ad blue nozzle there can
get blocked with either soot or blocked
with the uh crystals from the ad blue
itself
so I'm just spraying up the hand blue
injector there to soften up the soot and
then we can scrape any of the hard stuff
off one little pick
here now where this enters into the
exhaust here little port and that can
also block up as well
so we're going to clean that out okay so
now we're finished using that what's
what that's filled with is uh launch UK
DPF cleaning fluid and now what I've
also done is I've filled the cup here
with the launch UK fluid again
and we're going to now use this kit this
is the kit that comes with the fluid
here from launch we're going to get the
DPF now cleaned out okay so now what I'm
doing is I'm going to stick this nozzle
into the port where the blue come out of
and now that is connected to this gun
which is connected to my compressor at
130 PSI then we can squeeze the
trigger and get the uh
fluid sprayed in
[Music]
there
now we're just going to close everything
back
up okay now I'm going to start the car
up we'll hold the revs up at around
about 3,000 RPM for maybe a minute or
two and we're going to keep an eye on
that DPF
pressure we want to see that coming down
sort of under 50 if we
can try and get on the
graph
you see now that started off at
320 we're down to 170 now going to see
some smoke coming from the
exhaust just keep an eye on that want to
see how far down we we want to see that
reach like I said 50 m if we can now we
are down to 10 mbar at M we want to get
that a little bit lower than that so
we're just going to hang on for another
minute or two so just using a funnel
here to fill up the ad
blue okay now we've got 10 liters of AD
blue in here we need to go back in to
our special
functions we're going to go to exhaust
emissions and particle filter
replacement we need to do this to clear
the
code now that that's done it's going to
clear the fall
codes so we're just waiting for that to
finish
now okay that's all
complete switch ignition
off okay now if we go back up what we
can do is we start the engine back up
now if we come back to the fall codes
and we read them they should now be
gone so we go back to the live
data and we'll take the vehicle for a
little test drive okay we've got some
live data up here we can see now the S
is at 0% Millie bars at idle are at 0%
we'll try and hold the revs up around
3,000
RPM we can
let's we have 40 40 to 50
mbars and we'll take the vehicle on the
test drive make sure everything's
okay okay we're back from a test drive
all as well so we're just about finished
on this rain rovery vog so that's it all
finished and I'll see you on one of the
next
[Music]
videos
oh
