Land Rover P2047-13 Reduced Injector Circuit Open

AutoTuned TV
1 follower
Jul 21, 2024
adblue injector Fault with Land rover wiring harness.
for repair bookings or business queries email [email protected].
video questions or repair advice is not given via email.
[Music]
hello it's Jimmy here so I have here to
look at a Range Rover evogue he's got
some ad blue issues now of course this
usual story he's been to few guards as
who reset default and just said look we
don't know what to do apart from reset
default he said it does last a little
while so it doesn't come back on
immediately he can drive it away and
within a few days or maybe a week
default lights will come back on and
he's he's left with a a mileage
countdown so that's the message there
300 miles
until uh the vehicle won't
start we'll use the launch diagnostic is
the Euro tab
Tre okay I'll run a highspeed scan
so everything's nice and green apart
from this one nox exceedence nox
exceedence nox driver inducement active
that means the you've got the limited
amount of miles before it won't restart
reduced injector circuit
open
p247 I think I've done done I should
have done plenty of these before
yeah Land Rover Discovery sport p2047
that's the code we're looking
at uh repair the wire and harness SE
rink so probably going to be the same
job as that which is repairing the wire
and
harness uh got another one there yeah oh
didn't want to click on it I just wanted
to read
it yeah uh common issue obviously it can
be the ad blue injector but most
commonly the wiring really um
so well we don't need to look at live
data I'm going to get under the vehicle
and hopefully we can see the issue
straight away I think the customer did
say that the adlo injector has been off
and it's been replaced though
so maybe there's no visible visible
damage to to the
wiring I was going to say maybe it could
be the Ado injector but I think that's
already been replaced I'm sure he said
it's off and it's had new clamps and
injectors and everything uh but we'll
get underneath and have look okay so we
got it up on the
ramp get a Tor on there see if we can
see what's going
on yeah it looks like that's definitely
been replaced hasn't it
uh some cell tape here on the don't
think that's normal give these a
pull well there we go the uh wire there
has come out it's come out of the plug
but just a little bit of a
pull check the other one that's all
right as well not sure if that's normal
there to have
that cell tape there I can't
remember uh looks like we're going to
have to get this plug off maybe see if
we can fix oh we could have done with a
a new
replacement plug here replacement piece
of this harness but don't have one
um so going to have to see if I can do a
repair on this
one okay so I've unplugged it from the
injector there now I've got it down here
what I'm going to have to do for now is
cut this off from about
here now because this plug is a sealed
unit I have had to sort of cut it open
to get this out and heat um solder some
new piece of wire onto it now I just
waterproof that up with some
glue okay so now I've attached that
cables here and just put some heat
shrink on to uh seal them up now you
might ask how did
someone fit this without noticing the
cable um so the cable was attached but
of course it's only attached by the
rubber so the actual cable inside had
cored away and by giving it a little bit
of a pull I noticed that it came apart
um so that's how I noticed that the
cable is is uh wasn't really attached so
I don't think somebody just didn't check
check uh there give it a nice little you
don't you don't need to pull it too hard
but a little bit of a tug and and see if
it comes apart it should not come apart
okay now back in the vehicle we're going
to attempt to clear this fall code and
hopefully we have now fixed that circuit
issue so we're going to run the vehicle
for a few minutes and then rescan it
okay we can see there we've got three
fults go back
in
scan okay so now we just need to sort
out this nuok
exceedance um while we're here of course
I'm going to pull off the ad blue
injector make sure it's clean and also
make sure that the port inside is clean
and we'll put some some cleaner through
the Catalyst to clean off any sort of
dry now there is going to be dry residue
of um ad blue
crystallization the ad blue injector
hasn't been injected in uh so so
whatever is inside is going to have sort
of dried up um we'll get that sort of
cleaned out now so I'm just going to
open the clamp we'll get this off so
exactly as expected the ad blue injector
has already been cleaned but the actual
Port here where it goes into is blocked
it's really difficult to get the phone
in there okay so I using my little
nozzle here to poke my way
through should be a
there we
go just give it a little
wiggle and we'll squeeze the figer on
here we'll get this cleaning fluid
flushed into the
Catalyst get it cleaned
out okay so you can see there it's
starting to
[Music]
overflow okay so we're back in here
we'll get this out now
okay now we'll get back inside I hold
the revs
up what this is going to do is going to
flush all of that foam
out and what else we're going to do is
turn the engine off ignition on go to
special functions
and look for ad blue reset
uh we're looking
for that's not the option we're looking
for that's not the option we're looking
for
either okay for some reason the option
that I'm looking for is missing on that
tool so I might have to try another one
okay I'm going to try this tool
here okay so on this tool it's the
autofix D1
or D1 Pro I'm not sure I can't
remember uh let's have a
look no options not
there we go in here see if we can find
it okay so it looks like we're having
some trouble on here too cuz it's not in
the diagnostic
menu uh oh let's have a look in service
power train
sure there's probably some way if I go
through different options on there I
could have maybe maybe found it as well
but clear
adaptiv start
inhibit quality monitor reset that's
what I'm looking for that option right
there
so I've done loads of these with that
launch but I'm not sure why I couldn't
find this
there reset the quality monitor of
thecr sometimes what happens is when you
do a software update it actually um can
remove one or two of the items until the
software update is corrected so you can
maybe go back to the old software and
try it like that but right we'll just do
this this is why it's always handy to
have two tools or or three or four like
like I
have now what happens is it's going to
read Thea codes and now that we clear
the fa codes this time they should stay
away because we did clear them but the
scr codes did come back now if we clear
them like this this should stay away
permanently okay so that's
initializing press
okay okay let's start it
up see if that's
worked no that hasn't worked
surprisingly okay so I'm going to reset
the start inhibit see if that fixes this
issue that we've got
here for this countdown
okay back on the launch so the autofix
did have the option there but it the
reset isn't working so what I'm going to
do look back on
here
uh just look in the power
train there it
is okay we done that again looks like
it's worked this time so just check that
the ad blue tank is not re been
overfilled because that can cause this
not to reset but it's not right so a
very rare problem here with this Range
Rover is that I just can't get the noxic
seeding C to reset um even though I've
done in excess of 200 of these V cars
before uh we seem to have some sort of
software issue with this so I'm going to
have to send it to someone who's got
original Land Rover soft back to Land
Rover themselves and uh hopefully they
can they can do it I mean the ad blue
isn't overfilled
all of the resets are going through but
they're just saying that it's failed to
failed to um to reset it for some reason
uh unfortunately unless someone else has
got an answer for that it looks like
it's going to have to go back to Land
Rover maybe they can do some sort of
software update which should cure the
issue and uh see you on the next video
[Music]
