Vauxhall Vivaro P0201-13 Renault Trafic 020113

AutoTuned TV
AutoTuned TV
1 follower
Dec 14, 2024

Fixing a Vauxhall Vivaro P0201-13 Injector Circuit Fault: Step-by-Step Guide

Recently, a Vivaro came in with injector-related fault codes that had been persistent, despite the injectors being replaced. Below is a full breakdown of how the issue was diagnosed and resolved, step by step.


Understanding the Fault Codes

The main fault code we tackled was P0201-13, which refers to an injector circuit open on cylinder one. Additionally, there were related codes for cylinders two, three, and four:

* P0202 – Cylinder 2 Injector Circuit Open
* P0203 – Cylinder 3 Injector Circuit Open
* P0204 – Cylinder 4 Injector Circuit Open

This indicated a widespread injector issue. Despite having new injectors installed, the customer was still seeing these errors—and even worse, the van wasn’t running properly.

Symptoms the customer reported:

* Jerking and misfiring when accelerating uphill or under load
* No issues during steady cruising

Two separate garages had already suggested replacing the injectors again, but something didn’t add up. A deeper inspection revealed the real culprit: corroded or poorly connected wiring to the injectors.


Accessing the Injectors

To repair the problem, the first step was getting to the injector connectors. Here’s how we did it:

1. Remove the air intake pipe – This provides initial access to the area.
2. Pull the wiring loom out of its housing – Carefully disconnect anything in the way, such as vacuum lines or other cables.
3. Unclip and remove additional parts – Items such as the oil feed line and other wires may need detaching for better access.

Once everything’s clear, you’ll see the glow plug connectors and injector connections.


Inspecting and Cleaning the Connectors

The goal here was to improve the electrical connection. On inspection, one injector connector had visible darkened corrosion on the terminal—a clear sign of trouble.

Here’s what we did:

* Tightened the contacts: Using small picks, we carefully adjusted the connector terminals to close the gaps. This ensures a snugger fit onto the injectors.
* Scraped away corrosion: A pick was also used to clean up any built-up grime or rust.
* Used contact cleaner: A few sprays of fast-drying electrical contact cleaner helped improve conductivity.

We made sure to repeat this process for all four injectors, even if the others didn’t show obvious signs of damage. When it comes to connectors, it’s better to treat them all at once—it saves you trouble down the line.


Clearing the Upstream Pressure Pipe

While working on the engine, we also took the opportunity to clear the DPF upstream pressure pipe. Using a 12-inch cable and some DPF cleaner, we cleaned out any potential blockages. This step helps prevent clogging in the diesel particulate filter, which can trigger related warnings.

Pro tip: Be careful not to overload the system with DPF cleaner; a little goes a long way.


Putting It Back Together

After finishing the injector connector clean-up and pipe clearing, we reassembled everything:

* Reconnected all the wiring
* Put the intake pipe back in place
* Double-checked each component for a solid fit

Now it was time to start the engine and see how things looked.


The Results

As soon as the engine was running, there was some good news—the warning lights had disappeared. Without clearing the fault codes manually, the system recognised that the injectors were functioning properly again.

Using a diagnostic scanner, we confirmed that the injector-related codes were no longer active. Only a minor issue related to the battery current sensor lingered, which is common on these vehicles and unrelated to the injector fault.

A test drive followed to make sure the issue was resolved. The Vivaro performed smoothly, both at steady speeds and under hard acceleration. The jerking and misfiring were gone, and there were no faults on a final scan.


What Was the Real Problem?

Despite initial assumptions, the injectors themselves were fine. The root cause was worn or corroded connector terminals, which prevented proper communication between the injectors and the ECU. Cleaning and tightening the terminals was enough to fix the problem, proving that costly injector replacements weren’t needed at all.


Final Thoughts

If you’re dealing with injector circuit faults on a Vauxhall Vivaro, Renault Trafic, or similar vehicle, don’t rush to replace components based on fault codes alone. Corroded connectors are a common issue and are often the cheapest and quickest fix.

This quick repair saved the customer significant time and money—and more importantly, got their van back on the road without any hassle.

Got similar issues with your vehicle? Let us know in the comments or reach out for advice. See you in the next how-to!