Make wood any length with a basic scarf and epoxy

Nomad Boatbuilding
98 followers
4 Video Views·Dec 2, 2023
My website: https://www.nomadboatbuilding.com
Instagram: https://www.instagram.com/nomadboatbuilding/
It's not about the money but living isn't free...
Here are some ways you can support this channel.
Get 5% off TotalBoat products here: https://www.totalboat.com/?sca_ref=3715732.xvvNNHFDPJ
Get 10% off Starbond Adhesives. Use the Coupon code NOMAD10
Shop here: https://starbond.com/discount/NOMAD10
Buy some merch: https://www.nomadboatbuilding.com/shop/
Support these videos with monthly or annual pledges at Patreon: https://www.patreon.com/nomadboatbuilding
Or make a one time donation: https://www.paypal.com/paypalme/nomadboatbuilding
Howdy folks, Mark from Nomad Boatbuilding here.
Now today I'm going to talk to you about scarfing.
Scarfing is one of the cornerstone
techniques of wooden boatbuilding and that's because
we rarely get wood that is the
full length of our boat. We often have to make do
with shorter stuff. That's not the end
of the world because quite often to get
stuff that's as long as the boat you're going to build
you might have to compromise on
the quality of the wood or
maybe just the volume of wood.
I quite often find that the materials that
are long enough for the boat are often
kind of wonky and I might have to trim
half of it away in order to straighten the edge
or it just isn't very good quality to start with.
And I might
find something that's shorter with
really exceptional quality wood and just
being able to do a scarf joint in the middle of that
will double the length of that material
and give me a much more
quality result. The most
common version is a flat scarf
and that's where we have two pieces of material
with identical inclined planes
and when we glue them together
we get a continuation of the grain
and we get plenty of strength.
So we're going to be using this simple
scarfing jig. This is a sled for the table
saw so it just has a cleat on the back
side and a little piece of scrap
and then I've erected this little
right angle fence and that's to be able to
clamp our stock to. While I'll be taking
advantage of this table saw jig I have to cut
the scarf, it doesn't matter how you cut
it. More often than not I use my bandsaw.
Whether you use a circular
saw or even a hatchet, how you
cut the scarf isn't important. What's
important is that you get it finished to a reasonable
level of accuracy before gluing it.
And the material we're going to be scarfing
is a little bit deeper than the capacity of the
saw blade with the fence on
the saw so we're going to have to do a little
bit of work to finish that up by hand
but it's not a big deal and it's not a lot
of work. The length or ratio
of the scarf that you choose is important.
The bare minimum, the one
that I'm cutting here, is a 6 to 1
scarf. What I mean by 6 to
1, if your stock is 1 inch thick
the scarf needs to be 6 inches
long. For convenience we measure that
along the face of the stock, not along
the face of the scarf itself. Any
shorter than a ratio of 6 to 1 will result
in too much end grain in the scarf which doesn't
glue well. So the chances you'll get a good
structural bond are very low.
Now you can certainly go higher than 6 to
1. I often go
10, 12 to 1, sometimes even
a bit higher than that. Now what makes
me determine how long a scarf it is sometimes
depends on the situation.
If I'm gluing plywood that's going to become
planking or something like that, I tend
to go with the shorter 6 to 1 or 8 to
1 scarf. For something that's
going to take a lot of stress like a spar
you're going to want to go quite long
maybe 20 to 1.
More often than not, for things that I need to lengthen
gunwales, things that are going to be supported
by other parts, I will
often go with a 12 to 1 scarf
because that's a comfortable length
that tends to look good and has good
structural qualities when you need to bend
the part. This part is going to be
a grounding shoe on a boat that I'm building.
The portion of the boat that it
lays on is relatively flat and so I
can easily get away with this shorter 6 to 1
scarf. Now while a longer scarf
might be more intimidating and sometimes
a little more difficult to cut, they're
far easier to fit because any variation
in the angles between the two parts
are less critical in a longer scarf.
So I'm going to be using G-Flex to glue this up.
And the reason I like G-Flex
for this kind of thing, because it's a
tropical hardwood, which tend to be
a little oily in their composition
even if it doesn't necessarily feel oily
to your touch. So you should
always give it a wipe down with a solvent.
I've just used some alcohol,
but acetone would be the best thing to use.
And now I'm just going to mix up a small
amount of G-Flex. And one of the reasons I'm
using G-Flex for this, it's such a small joint
that I don't want to use
an epoxy that requires a pump system
like the regular
West System 105205
product. So G-Flex
is mixed with a
1 to 1, 50-50 mix.
So by using the scale, I can be
quite precise. Hey folks, I want
to break in here real quick to let you know that I've
been mixing this epoxy wrong up until now.
I've always gone with
1 to 1 by weight
because the instructions
all told me that you mix it 1 to 1.
Now I was talking with folks
at the West System and they noticed that I was
doing this and they pointed out to me that it
should be 1.2
to 1.
1.2 of resin
to 1 of hardener
if you're mixing by weight.
Now it doesn't say this in any of the
product instructions.
It does, however, mention it
in the product technical data sheet.
Their documentation should really
reflect this because that is a bit of a difference.
But
they said that despite the fact that
I've been mixing it a little bit wrong,
it's probably not going to be a big deal
because it's a very robust product.
Now this does answer the question that I had
of why my bottles
all seem to be a little bit disproportionate
in the amount that they've been dispensing.
I could never figure that out.
I always thought I was just being a little bit too
generous on one by accident.
Well, now I know. Alright,
let's get back to it.
There's about 2 grams of
the hardener.
Another 2 grams of the resin.
So you could do this by eye,
but I much prefer weighing it out.
That's much more accurate.
There we go. That's 2 grams of the
resin.
Of course, we want to mix thoroughly
because this is such a small amount.
We don't use my usual wand mixer.
Give it a good solid
1 minute, 1 to 2 minutes
of mixing.
I'll do a quick little
wet out on this joint
with the unthickened epoxy and then I'll just put
a tiny bit of thickener in there
in order to thicken up
what's left over and fill out the joint
a bit better. So I'm just going to
scrape this out hard
and in a perfect world
you might even give it time
for this to take up
before you put the joint together.
Give it, you know,
15 minutes or something
like that, but
that's not always the most practical thing
to do.
Now I'm just going to go and round up some filler.
I'll probably just use wood flour or something for this.
Okay, I've taken the
leftovers
and I've added a little bit of wood flour.
Wood flour, just sawdust
really. I mean, I've purchased it
but you can make your own. Get it out
of your sander
bag, but if you do that
you really should strain it.
Get yourself the finest strainer
you can find and see if you can't sift
it out and get rid of the real
heavy fibrous stuff.
Okay, we'll just coat out our joint now.
You only have to do the one side.
We'll flop our top piece
onto our bottom piece and we want to hold back
from the edge of that scarf
joint just a hair
between a sixteenth and an eighth, depending
on how much
epoxy you've got to fill out the joint.
Okay, now what
you want to do before you start clamping
the joint itself is isolate both pieces
so I've got this one piece
already clamped down that end of the
bench and I'm going to do the same thing to the other
one.
By doing that, it's going to prevent
this joint from sliding apart when I
put pressure on the joint itself.
Alright, so this is also when we want to
make sure we have good alignment between the
parts. Clamp that
down and I'll just grab a straight edge and check
that we have good alignment along here.
That looks just fine.
Okay,
now we're just going to put
a little something over
that joint and we're going to put a backing block
on this. So the backing block can be
anything that's the full size of the joint.
I'll just use this sanding block I have
here and I want to overlap
the
feather edge just a little bit.
Okay, then a small joint like this
you can probably get away with just one clamp.
Put the squeeze on there and we
just want to check alongside
to see that we're getting squeeze out.
See we've got a nice little bit of squeeze out
all the way across the joint and we just want to
just put enough pressure on there
that we're getting some squeeze out both sides.
Hopefully without causing
the joint to
spit out all of its
adhesive.
One side is a bit
acting a bit funny here.
Let's see what happens if I move my clamp
a little.
Yeah, I think we'll put two clamps on this one.
Could be I've got
a little bit of misalignment in my joinery.
That's why we like using
epoxy because it will make up for that
easily.
There we go, a nice bit of squeeze out
both sides. We'll just leave that alone. We won't touch
it. It's easy to clean up later on.
Okay, we're on the next day. Let's see how this
scarf turned out.
Beautiful. So when you pull back
the top surface and little hair
from your scarf lines,
what that does is it allows
a little bit of space for epoxy to fill
and in an ideal world
you'll end up with a nice flush surface because
you'll get a little bit of a glue line
right in through that little space.
Now if you screwed up and
you ended up being a little bit low from the
other surface, if you're smart
you'll have left your stock
just a little bit thick to be
thicknessed down again.
Maybe you didn't or maybe you just made it
your finished thickness right away. There's always
a good chance that you can get away with
a sixteenth of an inch less material
in your finished part regardless
and it probably won't make much of a difference.
A little bit of
shimming and adjusting and you
can probably get it right back to where you wanted it to
without any ill effect.
On the back side, that looks beautiful.
That's exactly what we want to see.
It's nice and even.
On the top we have a little bit of squeeze
out here because I pulled my
clamping block back a little bit and that'll
be just fine. So that'll clean up easily.
We can sand it off.
We could use a heat gun and scraper.
We could even use a block plane.
This G-Flex is fairly soft stuff.
In fact, I can put my fingernail
into it right now.
I can leave it later on. It'll harden
up a bit more from where it is because it's been
less than 24 hours.
But for the most part, that's perfectly
structural right now.
While I'm using a belt sander to clean up this
particular scarf joint, more often than not
I just reach for a cabinet scraper.
I find a cabinet scraper,
especially a particularly hard one with a
small hook, works really great for cleaning
up epoxies. I like to make
my own out of worn out Japanese saw blades.
I cut them down with an angle
grinder, put whatever shape I want onto
them, roll a burr onto the edge,
and away you go. So there's our
finished glue line. That looks
just fine. Well, I hope
this has demonstrated that scarping is actually
quite easy to do. The most critical part
is laying out your joint accurately.
When it comes time to cleaning up those mating surfaces,
err on the side of a hollow
surface as opposed to a humped surface
because thickened epoxy will
fill that hollow and create a perfectly
sound structural joint.
Now, of course, you don't need to use epoxy
to glue a scarf together. You can use
other adhesives, but thickened epoxy
offers a lot of peace of mind
and a lot of wiggle room for inaccuracies.
Now, if you enjoyed this video,
you're just getting started in boat building, you need a bit
of guidance, please feel free to join me
over on Patreon where I offer all kinds of
personalized support. You can find links in the
corner or down in the description.
Alright folks, we'll catch you later.
