RC HPF || RC DIFFERENTIATOR - PROBLEMS || ECT202 ANALOG CIRCUITS || KTU
This topic is also in the syllabus for
1. ECT202 ANALOG CIRCUITS:https://youtube.com/playlist?list=PL2UV2EJdMQmhbgPiP-dnVeRNTF0Pcfmpk
2. EC205 Electronic Circuits: https://youtube.com/playlist?list=PL2UV2EJdMQmiePALNs84TJUONtzApG9pp
3. CS 207 Electronic Devices and Circuits: https://youtube.com/playlist?list=PL2UV2EJdMQmh9Royg7s7B78IiWpou-lE0
4.ECT 281 Electronic Circuits ( Minor): https://youtube.com/playlist?list=PL2UV2EJdMQmiduKsGRgNFuu_MqB__HVpN
#circuits #ktu #ece #electroniccircuits
These are some of the problems and solutions related to RC circuits.
We have completed the topic of linear wave shaping circuits.
Today, we are going to discuss some questions related to this topic.
Let's look at the first question.
Proof that the following circuit works as a differentiator.
R is much larger than XL.
Vout is equal to L into di by dt.
R is much larger than XL.
I is equal to Vout by R.
Vout is equal to L into di by dt.
Output is the derivative of input.
So, the circuit works as a differentiator.
The second question is to design a differentiated circuit to differentiate a square wave of
10 V peak-to-peak amplitude and frequency 1 kHz.
The third question is to draw a circuit diagram of the differentiated circuit.
The circuit diagram of the differentiated circuit is as follows.
What is the condition for a circuit to work as a differentiator?
RC should be less than or equal to 0.00160.
This is the condition for a circuit to work as a differentiator.
What is the difference between frequency and time period?
Frequency is 1 by time interval.
Time interval is 1 by frequency.
Time interval is 1 into 10 raised to 3.
That is, 1 millisecond.
Time constant is 1 millisecond.
RC is equal to time constant.
RC should be less than or equal to 0.00160.
RC is equal to 0.00160 into 10 raised to 3 is equal to 0.0016 into t.
RC is equal to 0.0016 into 10 raised to minus 3 whole divided by 160 into 10 raised to 3.
RC is equal to 0.00160 into 10 raised to minus 12 whole divided by 160 into 10 raised to minus 12.
RC should be less than or equal to 0.00160.
Frequency is equal to 1 by frequency.
Frequency is 1 kilohertz.
Kilohertz is equal to 10 raised to 3 hertz.
1 into 10 raised to 3 is equal to 1 millisecond.
T value is 1 millisecond.
RC is less than or equal to 0.00160.
RC is equal to 0.00160 into 10 raised to minus 3 whole divided by 160 into 10 raised to minus 3.
Frequency is equal to 10 hertz.
Amplitude is equal to peak to peak amplitude.
V peak to peak is equal to 4 volts.
Plot the output waveform given lower 3 dB frequency.
Lower 3 dB frequency is the cut-off frequency in this case.
Cut-off frequency f1 is lower 3 dB frequency.
It is given as 5 hertz.
Cut-off frequency equation is 1 by 2 pi RC.
It is given as 5 hertz.
We are asked to plot the output waveform.
When we give a square wave input to a RC high pass filter, the output waveform is tilted square wave.
We have uploaded a video on how to plot a tilted square wave.
If you have any doubt, please refer to that video.
We have studied some design equations there.
Based on that, we have to solve this problem.
Let us plot the general figure.
We give a square wave input to a high pass filter.
When we give a square wave input to a high pass filter, we will get a tilted square wave as output.
We have studied some design equations there.
I have told you that we need design equations to plot this.
Design equations are V2 is equal to V1 e raised to minus T1 by RC.
V4 is equal to V3 e raised to minus T2 by RC.
V is equal to V2 minus V3.
V is equal to V1 minus V4.
These are the design equations studied there.
We need to remember all these equations.
V2 is equal to V1 e raised to minus T1 by RC.
V4 is equal to V3 e raised to minus T2 by RC.
V is the input peak to peak.
V is equal to V2 minus V3 or V1 minus V4.
These are the design equations.
Based on these design equations, we need to find corresponding values V1, V2, V3, V4.
Only if we know these values, we can plot this waveform correctly.
We need to find these values.
Here, we are given a cut-off frequency.
Cut-off frequency is given as 5 Hz.
Cut-off frequency is 1 by 2 pi RC.
1 by 2 pi RC is 5 Hz.
RC is equal to 1 by 2 pi into 5.
That is 1 by 10 pi.
We got the value of RC as 1 by 10 pi.
RC is 1 by 2 pi into 5.
That is 1 by 10 pi.
RC is 1 by 2 pi into 5.
RC is 1 by 10 pi.
and
frequency is 10 Hz
frequency is 1 by time period
time period is 1 by 10
total time interval is 1 by 10
T1 is equal to T2
T2 is equal to T by 2
T1 is equal to T2
T2 is equal to T by 2
peak to peak value is 4 V
T1 is equal to 1 by 20
T2 is equal to 1 by 20
V2 is equal to V1 e raised to minus T1 by RC
V2 is equal to V1 e raised to minus T1
T1 is equal to 1 by 20
V is equal to V2 minus V3
V is equal to 4
4 is equal to V2 minus V3
V2 is equal to 4 minus V1
RC high pass filter for a frequency of 1kHz

