COMPARATOR - STATIC CHARACTERISTICS || EC462 MSCD ||MIXED SIGNAL CIRCUIT DESIGN || KTU || MODULE 3
#ktu #s8ece #mscd
For full class:
https://www.youtube.com/playlist?list=PL2UV2EJdMQmim5UHGAuX6HtsAVCRB-2Ix
Hi all, today we are discussing about comparators.
So, what is a comparator?
Comparator is an analog input with analog signal with another analog signal or reference
and produces an output.
That output is a binary based on comparison.
What is a comparator?
Comparator is a circuit.
What does it compare?
It compares analog signals with another analog signal or reference.
After comparing, what does it produce?
It produces an output.
What is an output?
It is a binary signal.
After comparing, what does it produce?
It produces a binary signal.
The comparator is a circuit that compares an analog signal with another analog signal or reference
and outputs a binary signal based on comparison.
After comparing, it produces a binary signal.
It is widely used in the process of converting analog signals to digital signals.
There are mainly two types of comparators.
They are open loop comparator and regenerative comparator.
There are mainly two types of comparators.
They are open loop comparator and regenerative comparator.
Open loop comparators are basically op-amps.
What is an open loop comparator?
It is an operational amplifier or op-amps without compensation.
It does not provide any feedback.
Open loop comparators are basically op-amps without compensation.
That is what an open loop comparator is.
What is a regenerative comparator?
It provides feedback.
Regenerative comparators use positive feedback.
A regenerative comparator has positive feedback.
There is a third type of comparator.
It is a combination of open loop and regenerative comparators.
There is a third type of comparator.
There are mainly two types of comparators.
They are open loop comparator and regenerative comparator.
Open loop comparators are basically op-amps without compensation.
Regenerative comparators use positive feedback.
There is a third type of comparator.
It is a combination of open loop and regenerative comparators.
Let us see the characterization of a comparator.
This is the circuit symbol for a comparator.
The circuit symbol of a comparator is like the symbol of an op-amp.
There are two terminals.
There is a positive terminal and a negative terminal.
If the difference between the two terminals is positive,
a positive binary will be produced in the output.
If the difference is negative,
a negative binary will be produced in the output.
That is what is done here.
Let us see the working of this.
What is working?
A positive voltage is applied at VP.
Input will cause the output to go positive.
If a positive voltage is applied at VP,
it will make the output positive.
Whereas, if a positive voltage is applied at VN,
input causes the comparator to go negative.
Which is more positive?
If a positive voltage is applied at VP,
it will produce a positive output.
If a positive voltage is applied at VN,
it will produce a negative output.
That is the concept.
The upper and lower voltage limits of the comparator output
is defined as VOH and VOL.
The output produced by the comparator
has an upper limit and a lower limit.
The upper limit of the output produced by the comparator
can be denoted by VOH.
The lower limit can be denoted by VOL.
Let us look at the static characteristics of the comparator.
The figure shows the output of op-amp is high
when the difference between inverting and non-inverting input is positive
and low when the difference is negative.
This can be modeled by an ideal circuit element shown below.
Let us look at the characteristics of the comparator.
The positive and negative values of the comparator
are determined by the difference between the two inputs.
If the difference is a positive value,
the output will be VOH.
If the difference is a negative value,
the output will be VOL.
If the difference is a positive value,
the output will be VOH.
If the difference is a negative value,
the output will be VOL.
The difference between inverting and non-inverting input is positive.
If the difference is positive,
the output will be VOH.
When the difference is negative,
the output will be VOL.
We can represent the comparator using ideal circuit elements.
This diagram shows the ideal circuit elements of the comparator.
Vp and Vn are the two inputs.
This is the circuit diagram of the comparator.
Vp and Vn are the two inputs of the comparator.
When the comparator performs a function,
it finds the difference between Vp and Vn.
This is F0 of Vp minus Vn.
The difference between Vp and Vn is the output.
F0 of Vp minus Vn is VOH for Vp minus Vn greater than 0.
If the difference between Vp and Vn is positive,
the output will be VOH.
If the difference between Vp and Vn is less than 0,
the output will be VOL.
This is a voltage controlled voltage switch.
It comprises a voltage controlled voltage switch.
The ideal aspect of this model is the way in which
the output makes a transition between VOH and VOL.
The output changes states for input change of delta V.
The ideal aspect of this model is the way in which
the output makes a transition between VOL and VOH.
The output changes states for VOH and VOL.
The ideal aspect of this model is the way in which
the output changes states for input change of delta V.
The output changes states for input change of delta V.
We can write the gain equation.
The output divided by input is the gain equation.
The limit delta V tends to 0.
The change in the output is VOH minus VOL.
The change in the output is corresponding to the change in the input.
We can write the change in the input as delta V.
We can write the gain equation as
gain AV is equal to limit delta V tends to 0,
VOH minus VOL divided by delta V.
This figure shows the transfer case of a practically realizable comparator.
This figure shows the transfer case of an ideal comparator.
In a practical case, the output does not have to be positive.
The output is stable only when a particular voltage reaches VOH.
Similarly, the output is stable only when a particular negative voltage reaches VOL.
The figure shows the DC transfer curve of the first order model.
This is an approximation to a realizable comparator circuit.
We can write the gain equation as
the limit delta V tends to 0, VOH minus VOL divided by delta V.
The change in output voltage divided by change in input voltage.
The gain equation is VOH minus VOL.
The corresponding input is VIH minus VIL.
In a practical case, the gain equation is VOH minus VOL divided by VIH minus VIL.
VIH and VIL represent the difference in input voltage.
VIH minus VIL is the same representation of delta V.
VIL and VIH represent the input voltage difference.
That means Vp minus Vn.
The difference in input voltage is the difference between Vp and Vn.
VIL and VIH represent input voltage difference.
Vp minus Vn is needed to just saturate the output at its upper and lower limit.
In VIH and VIL, the output is in saturation.
When VIH reaches a certain voltage, the output is in saturation.
Similarly, when VIL reaches a certain value, the output is in saturation.
These two values are needed to saturate the output at its upper and lower limit.
This input change is called resolution of a comparator.
VIH minus VIL is the resolution of a comparator.
That is the resolution of a comparator.
The resolution of a comparator is this.
The upper output voltage needs to be in saturation and the lower output needs to be in saturation.
The difference in input voltage is called the resolution of a comparator.
This curve in figure 3 is the transfer curve.
We can draw a circuit model for this transfer curve.
The difference between Vp and Vn is Vp minus Vn.
The voltage here is F of Vp minus Vn.
F of Vp minus Vn is VOH.
Vp minus Vn is higher than VIH.
When Vp minus Vn is higher than VIH, F of Vp minus Vn is VOH.
F of Vp minus Vn is VOH for Vp minus Vn greater than VIH.
Similarly, when Vp minus Vn is less than VIL, F of Vp minus Vn is VOL.
F of Vp minus Vn is equal to VOL for Vp minus Vn less than VIL.
A linear variation occurs between VIL and VIH.
The output voltage of the comparator is AV into Vp minus Vn.
The corresponding value is AV into Vp minus Vn.
This is the equation in the case of a practical comparator.
This is the second non-ideal effect seen in a comparator.
The second non-ideal effect is the input offset voltage.
In the case of an ideal comparator, the output changes when the input crosses zero.
When the input is a positive value, it changes to VOH.
Similarly, when the input crosses a negative value, it changes to VOL.
Similarly, when the input is a positive value, it changes to VOH.
Similarly, when the input is a negative value, it changes to VOL.
This transition occurs between VOH and VOL when the input crosses zero.
But sometimes, this transition does not occur in the output.
This is because there is a certain offset voltage in the comparator circuit.
The difference in the input is achieved only when it reaches that offset voltage.
Only then does the transition occur.
The non-ideal effect caused by the offset voltage is the output switching.
Let us look at this.
This is the offset voltage of the comparator circuit.
This is the input voltage of the comparator and this value is the offset voltage of the VOS.
Usually, the switching process of a comparator is done at the point where the zero crosses.
But here, only when the output voltage of the comparator is more than the plus VOS voltage,
the switching process of the comparator will take place to the VOS.
Here, you can see that the transfer current of the comparator is shifted to the right from zero to VOS.
This is an example of a non-linear effect.
This is a non-linearity that occurs when the offset voltage of the comparator is more than the plus VOS voltage.
We can represent it using the corresponding components.
This is Vp, Vn.
The effect of Vp on the positive is VOS.
VOS is the offset voltage.
The output voltage of the comparator is Vp.
Vp dash is the output voltage.
Why do we add the Vp signal?
We add it using VOS.
So the character of Vp will of course change to the right as VOS times.
We discussed the effect of non-linearity based on the offset voltage.
In addition to above characteristics, the comparator can have differential input resistance and capacitance and output resistance.
Input Common Mode Range or ICMR is also very important to determine the characteristics of the comparator.
ICMR for a comparator would be the range of input common mode voltage over which the comparator is functioning normally.
The noise will lead to uncertainty in transmission.
For example, if the actual curve of the comparator is like this, there will be an RMS noise coming into the transfer carrier.
This makes an uncertainty.
So today we discussed about the comparator, its circuit, open loop and regenerative.
We also discussed about the characterization of the comparator, its symbol, its working and its static characteristics.
Tomorrow we will discuss about its dynamic characteristics.
In the next class, we will discuss about its static characteristics.
Static characteristics are the output and input.
Input is Vp-Vn.
Output is either high or low.
These are the two binary values.
This is the function of the comparator.
In the practical case, the transfer carrier will be like this.
There will be some irregularity in this.
Irregularity is created by offset voltage.
We can see that the transfer carrier is shifted by offset voltage.
Other irregularities are differential input resistance, capacitance, output resistance and ICMR range.
All these are important to create non-linearity.
Due to the effect of ICMR, certain noise will come in and distort the output carrier.
We discussed about the comparator and its static characteristics.
In the next class, we will discuss about the dynamic characteristics of the comparator.
I hope everyone understood today's session.
See you in the next class.

