432. Trimming a Sake Bottle on Chucks with Hsin-Chuen Lin 林新春 清酒瓶修坯示範

Hsinchuen Lin
205 followers
1 Video View·May 8, 2020
To see or buy my finished work and pottery tools, please visit my ETSY shop:
http://www.etsy.com/shop/potterysquare
http://www.etsy.com/shop/hsintools
http://www.etsy.com/shop/hsinchuen
To watch more of my throwing videos, please visit my channel:
http://www.youtube.com/user/hsinchuen/videos
To learn more about my back ground, please visit my Website:
www.mypots.net
Follow me on Instagram: hsinchuenlin
Like me on Facebook page: Hsin-Chuen Lin Ceramics
Today I am going to trim this sake bottle I made a couple of days ago.
Before I trim, I usually like to take care of the spout here because when I try to pinch
the spout, this part here isn't quite smooth yet and also to prevent from dripping when
you pour the liquid or the Japanese wine, rice wine, and you don't want to have a drip.
So usually I like to take care of that part here.
So what I'm going to do is using a sharp knife and just cut out.
So what I was doing is trying to get the lips so when I'm pouring, hopefully the liquid
will not climb back on.
It's like when you are making a container, usually the container has a little overhang
so when some liquid is coming out from the container, it will just stop right here.
So this is what I was doing so that when the liquid comes out, it hopefully will stop right
there.
So that's what I was doing.
And now I'm going to turn it upside down and trim.
Since this part is kind of narrow, if I just hold it like that, it's a little bit unstable
and it's very easy to tip over unless you use a lot of clay to hold it or you have the
grip that you can grip it on.
I don't have that and I don't like to use that.
So I have my own chuck that I will be able to hold it on.
So here I have a smaller chuck that size is fitting, but it's not tall enough.
So I'm going to increase the height by sticking two chucks together.
So first, let's see if this is fitting there.
Right, so it's fitting, but you see it's coming out, so that's too short.
Actually, if you want to make something that you can trim like the sake bottle, you could
make it a little bit taller, but I don't have it.
So I'm going to stack up two of them together.
This is my device here.
You can see I have one larger one, and actually I trimmed a little groove here, so this one
is sitting right on top of it easily.
So that's my setup.
Roughly center it first, and by the way, for using the chuck, usually when you have your
own studio, you can keep your chuck in the dead hard stage for a long time.
But for the studio, if you have a shared studio, usually people will fire the chuck into the
bisque stage, and the bisque chuck is very porous, meaning it's absorbing water easily.
So if you try to use a clay to stick it on, the clay is not going to stick because the
chuck is very porous, it absorbs water right away.
So to prevent that from happening, usually I soak my chuck in water for maybe 10-15 minutes
until it doesn't take water anymore, and that way when you try to use a clay to stick, it's
easier for the clay to stick on it.
So that's the tip for you.
Right, and then carefully put my bottle in.
And if your piece is cut on the flat surface, you can actually use the bubble leveler to
level it.
But this one was cut off, the hum is not quite level, so I am not going to do that.
So the clay is sticking quite well, you see that if you soak it in the water.
You can use a needle tool or use the corner of the trimming tool to get yourself an idea
where you want your foot rim.
So right here, from here to here will be the rim of my foot.
I can remove a little clay here and a little bit of clay there.
Okay.
So that's how much clay I dig from the sand.
And usually by tapping the sand, when it's thinner, the sand gets higher.
When you get to the right depth, then you will be able to compare the outside and the
inside.
So there's quite a bit of clay that I could remove from the outside too.
Okay, so that's the foot trimming.
Spend quite some time to dig out the clay in here and then try to remove more clay from
here.
So the whole piece will be much lighter.
Okay, so that's the sake bottle that I trimmed upside down on the chalk and the whole finished
piece.
And if you want to do a little bit of decoration, just spend some time and you're going to do
a tattering or you're going to do a scrubiddle and the whole piece will look much nicer.
