270. Throwing a Small Thin-necked Bottle with Hsin-Chen Lin 林新春 示範細頸瓶

Soul of Siberia
114 followers
1 Video View·Dec 7, 2022
To see or buy my finished work or pottery tools, please visit my ETSY shop:
http://www.etsy.com/shop/hsinchuen
To watch more of my throwing videos, please visit my channel:
http://www.youtube.com/user/hsinchuen/videos
To learn more about my back ground, please visit my Website:
www.mypots.net
Hi, before I start my today's demonstration, I have a little information to share with you.
This coming March 22nd to 24th, I will be at the NCCA, which is going to take place in Portland.
It's a clay conference, national conference. I will be at my booth number 701,
selling my tools. Here's the list of my stainless trimming tools, a set of 10.
I made it myself. It's very sharp and very useful for all different kinds of trimming projects.
So this is the trimming tools, and also recently I have been invent, I can say invent,
a measuring tool that you will be able to measure the thickness of the bottom. Usually
by just looking at it there, it's hard to gauge how thick the bottom is, but with my measuring tool
you can measure the inside and you got a reading. I have put the ruler here right in the middle
and also you can pull it out and then I measure the outside.
Okay, so you get the difference of measuring and you subtract the outside part from the inside
and you get the thickness. So this is my invention for making the trimming job easier and you don't
go through your part or you don't leave your bottom too thick, you got exactly the reading.
So this is a very useful tool to use. I will be selling my measuring tool as well in NCCA.
Also here is the wooden rib. The ribs, I got two different sizes, four inches and it's from
different wood and also five inches, which you can make perfect balls and smaller ball,
larger ball and even a platter. This is a very good special design for making nice and perfect
balls. So I hope to see you there. Today I like to throw a thick neck paddle. The neck is tall and
thin. This piece of clay is around two pounds. So I usually leave my base, the bottom three and
eighth inch thick. Ready to trim, I will show you my measuring tool on the exact thickness.
So I compress the bottom a couple times. Okay, my cylinder narrow. Now I am lifting.
You can see that I am actually using my left thumb and the inside finger to lift it up.
And you see that my right hand there is just to stabilize. Actually the major lifting is from my
left fingers. So the right hand is just stabilizing and left hand to the lifting.
Since I'm making a thin neck paddle, so I would keep the cylinder a little bit narrow.
So later on, it would be easier for me to make it even thinner. But for now,
I like to make the paddle shape look a little bit nicer before I close it. It's slippery.
By adding slip, remove the slip from my fingertips and add it to the surface of my cylinder.
Cylinder is low but very steady. Making sure that the bottom portion, this part here,
is nice and smooth before I close it further. The bottom is nice and smooth. Now I'm going to
just chuck it on the neck. In the meantime, I'm index finger there on the top to
control the rim. After I color in, the neck will be thicker and narrower. So I'm just lightly
pulling it so that I don't have so much color here on the neck. So just by lifting my inside
finger and outside and just lift the wall. And the right hand is just to stabilize it.
It basically is my left thumb and the inside finger. So by lifting five fingers like a crawl
to shrink the neck even further. Just pinch here and my right hand is to stabilize it.
Roll and lift and then smooth the curve. So I'm using the curve of my metal to get a nicer curve
on the neck. So I like to use this metal rib because it is flexible so I can bend it to
make many different curves. This kind of curve and this kind of curve.
So I can bend it here and then bend it here so I have many different curves. After I finish,
I like to trim a little clay off the foot. I'm holding this tool like holding a pencil
and slowly spin my wheel and just slowly insert trim until I touch the bed.
And then I slowly pull it out and then using my number 10 trimming tool and just undercut
the clay and you should be able to cut it and remove it easily. Okay so it's very easy to
cut it underneath with this very thin blade. You just undercut it and because this is thin so
not like the needle tool that usually you push the clay back and sometimes it sticks on the wall
here. And using the thinner blade it's easy to undercut it and after you cut it it's very easy
to remove it. Okay so I will show you how I trim this bottle. It needs to be sitting on the chuck.
Okay so I'm gonna make a chuck about this wide so that you will be able to sit it right here
and trim it. Okay thanks for watching.
