Fixe Hardware's Hely PLX-HCR forged glue in bolts, installed with Hilti 500 v3 epoxy, snapped in shear at 30.94kn and 29.80kn and 27.74kn. This is one of the few bolts that only requires a 3/8" hole and the duplex stainless supposedly gives it more corrosion resistance. Please don't bolt if you don't need to and use titanium if near the ocean and never use plated steel bolts outside. - with Bobby Hutton
HIGHLINE UNIVERSITY INTERNATIONAL www.howNOTtohighline.com
All donations go straight back into making this channel better. We put donors names in the ending credits and give them exclusive access to the SlackSnap and BoltBuster Raw Data spreadsheet + corresponding footage associated with each break.
Do you want to see the PLX-HCR Peely Forged Glue and Bolt from Thicks Hardware break in
shear with Hilti V3500 glue in our concrete test?
Check it out on this episode of How Not to High Line.
Hi, I'm Ryan Jinks, and welcome to Bolt Busters, where we're breaking a lot of climbing bolts
in order to satisfy all of our curiosity about what we can do with these and not die.
Today, we're going to break test the Thicks Hardware's Forged Glue and Bolt.
It has a weird name, the Healy HCR PLX Duplex Stainless Glue and Bolt.
Now, let me explain some of that.
The PLX part of that is a duplex steel.
Duplex steel is stainless steel, but fancier.
It's supposedly more corrosion resistant and a little bit more resistant against stress
crack corrosion, which can happen in corrosive environments like in Thailand or near the
beach. However, there are some scenarios that have been reported where this, at least in
the past, has kind of rusted.
So right out the gate, I just want to say if you are going to be right next to the ocean,
we do recommend titanium bolts because those will never corrode in your lifetime.
So if that is an issue for you, please go with titanium.
But anyways, these are pretty fancy.
The way this rod goes is in order to, the point is for it to eliminate bubbles.
So as you install it and as you twist it in, the glue will surround the shaft entirely.
As far as the head goes, it's not welded like so many other glue and bolts.
Other bolts that don't have welds on them, like the wave bolt, are basically a skinnier
rod that goes around and is bent to be in the shape it needs to be.
And what I don't like about those is you're dealing with a skinnier rod.
This has a nicer surface to pull, which you can thread your rope in directly.
As far as the eye size goes, you can get three carabiners in here, two of which you can
load properly, but the third one is not going to sit in there well and probably break
significantly lower than it's rated.
Our first break test was pulling, pulling, pulling, and it stressed out the first inch
of the rod until it snapped at 30.94 kilonewtons.
We did again and it broke in the same way where it snapped right below the surface of
the concrete at 29.8 kilonewtons.
Broke, broke the bolt out of the hole.
It breaks it in the same way as it does when we test it in tension.
29.8.
And our last test broke again in the same way at 27.74 kilonewtons.
Okay, 123 broke the same way.
Oh my gosh, this slo-mo thing is so annoying.
123 broke the same way, popped the glue, it has some concrete still attached to it.
Bolt snapped and so, okay, let me break that, bubby.
27.7.
27.74.
We used the Hilti B3500 glue.
We really liked that glue.
It is probably the best epoxy on the market.
However, our glue was four months expired, but it had no effect on this test.
And we also like to test if expired glue is good.
And it is technically a lot cheaper for us to use expired glue.
The Bolt Products Solid Leg 8mm bolt, which uses a 10mm hole, just like this one.
Also broke basically almost exactly the same as this one.
So they're very, very comparable.
Now, these are in the 30 range.
If you want to use the Titan HD threaded concrete screws, you can get them in
stainless steel and they're breaking around 40, mid 40s kilonewtons.
They're quite a bit stronger.
They're a lot cheaper to install.
So if money is an issue for you, they're pretty much just as good.
They're the workhorse of all of our brake tests.
When we need to stabilize our hydraulic cylinder or we're testing hangers.
That's our go-to bolt.
And I recommend that if money is an issue for you.
Um, these aren't bad and they're not something I'm, you know, stoked on.
They're just, they're just there.
If you're curious about how to install bolts, glue in or mechanical, go to the
bolting Bible on slackademics.com.
We have a lot of information on there.
We're going to update all of it this winter after we break test a couple
hundred more bolts and it's raining outside.
So stay tuned every week to how not to Highline as we're going to be sharing
more and more brake tests, and we will be telling you when that will be updated.
So make sure you like follow and subscribe in order to catch all
the stuff we're putting out there.
Cheers.
Hey, thanks for watching, but don't be an idiot and try highlighting
without going with somebody who knows what they're doing.
The first time you go out, we actually have available now the Highline
university international, which is a to Z everything you need to
know before you go highlighting.
This teaches you how to use a Highline that's already rigged.
So let's talk about some leash management.
That's the H zero course, which is out right now and available
at how not to Highline.com.
It's over a hundred videos with quizzes, PDFs, illustrations, and it
comes with homework and teachers that you submit it to.
It's a very interactive online school.
So you get to learn in person online.