Bolt Buster - dewalt powerstud stainless wedge bolt - climbing and highline bolt break test

HowNOT2
100 followers
5 Video Views·Dec 7, 2019
Wow. ½” dewalt power studs proved to be hard to break with our early setup. Tested in shear in concrete, we had the first one break the hanger at 48.88kn and the 2nd one didn’t break at 54.94kn and the last one we finally snapped at 60.92…. WITH A 30KN FIXE HANGER!!! If you're working with solid rock, these were impressive. Please don't bolt if you don't need to and use titanium if near the ocean and never use plated steel bolts outside. With Bobby Hutton
Support these projects through our new coffee company https://www.brewjuno.com
Highline University, Bolting Bible, Book of Slack... all the good stuff is at https://www.hownottohighline.com/
Do you want to see how strong a half-inch DeWalt power stud wedge bolt is when we pull it in shear?
Check it out on this episode of How Not to Highline.
Hi, I'm Ryan Jinks and welcome to Bolt Busters where we try to break everything climbing bolt
related in every possible scenario just because we're curious. And today we're curious about
the half-inch power stud from DeWalt. This is a wedge bolt, this is stainless steel,
and this is a quality product. So what we use on here for a hanger is Fix Hardware's 30 kilonewton
304 stainless steel hanger. This is about $2.95 retail on their website. Wedge bolts can be great
in something hard like granite, but in something soft like sandstone or some layered rock, you
would not want to put a wedge bolt in because it's only putting pressure on the sides here.
Basically what you have is a cone built into the stud. Threads on top, cone on bottom.
And this sleeve on the bottom gets sucked down into the cone. Now the negative side,
what I don't like about wedge bolts is the tighter you make this, the higher the bolt goes.
And sometimes when you put them in, it takes a while for it to engage. And what happens is
this bolt's sticking up that high, kind of in the way of multiple carabiners if you have it
sticking out like this. So a sleeve bolt is my preferred mechanical bolt, if it's not a temporary
one, which would be the Fix Hardware's Triplex bolt. But anyways, the reason a sleeve bolt works
better in my mind is because the nut at the top stays flat all the time. Because this is a five
power bolt, what it is is a threaded screw. And at the bottom of this thing is a nut. The nut
is wedged. And as it goes to get sucked up, it's getting sucked into this sleeve that separates
as you try to suck the nut up. And so what happens is the bolt itself is just spinning
in place the whole time. That's how sleeve bolts work. Now back to our half inch wedge bolts.
The first brake test, we put a 14 millimeter quick link on there and pulled and pulled and
pulled until the hanger basically turned to taffy and it pulled the quick link through at
48.88 kilonewtons. The next week we decided to do another test because we do like to do three
of everything. And we got 54.94 before our hydraulic cylinder would not give us any more muscle.
So the first time we discovered that our hydraulic cylinder was too small.
And so we, the next week got another one and we broke a fresh bolt at 60.92
kilonewtons and that snapped the head off of our bolt.
10, 30, 40, 50.
So we got three very different results here with the hanger breaking. The other one didn't break,
but they both looked like they were about to go. And then the last one broke the bolt.
So it's quite interesting that a 30 kilonewton hanger can keep up with such a strong bolt.
I'm pretty happy with it pulled in sheer. We will do another video on us pulling in tension
straight out, but it's quite a range to go from 68 to 60 kilonewtons.
But that is basically dependent on the hanger more than the, uh, the bolts performance,
depending on what rock you're doing, where you're trying to install this and what you're trying to
accomplish. I believe this setup is pretty good. Just make sure you're not using zinc plated shit
because it will rust over a shorter period of time. And don't put these things near the ocean
that requires a titanium bolt. So it'll last a long, long time. You can read all the stuff you
need to, to learn how to put in bolts at the bolting Bible on slackademics.com. We're going
to be rewriting the bolting Bible with all of this new information we're getting in gathering
from bolt busters and all this stuff that you guys, the audience have given us feedback on,
because this is a collaborated effort to collect everyone's knowledge into one place.
So we have a great entertaining resource for people who want to learn how to bolt and bolt
well. And that way we can keep our climbing and highlighting areas nicer, longer. We post
every week, a bite sized episode about three break tests generally. And so make sure you like
follow and subscribe on Facebook, Instagram, and YouTube in order to catch them all. Cheers.
Hey, thanks for watching, but don't be an idiot and try highlighting without going with somebody
who knows what they're doing. The first time you go out, we actually have available. Now the
Highline university international, which is a to Z everything you need to know before you go
highlighting. This teaches you how to use a Highline that's already rigged. So let's talk
about some leash management. That's the H zero course, which is out right now and available at
hownottohighline.com. It's over a hundred videos with quizzes, PDFs, illustrations,
and it comes with homework and teachers that you submit it to. It's a very
interactive online school. So you get to learn in person online.
