Tenex Tec is a polyester arborist rope that is rated to 83kN. It is hollow braid which means it's meant to be spliced. We tested this rope with one fid bury instead of two like it requires. We were able to get full strength out of it. When we pulled the last test to 85kN, the machine struggles to go past that so I stopped, thinking it wasn't going to break. Walked around my shield and then this explosion of 19,000lbf happens. I swear it feels like some of those breaks give off small shock waves. Read more about these tests and see our data on our blog https://www.hownot2.com/post/arborist-gear-1
00:00 Tenex Tec 5/8" Tests 06:43 Prusik Cord on 1/2" rope Tests 09:16 Arborist saddle tests 13:02 Buckle Test 13:49 Bridge Plate Test
Not quite sure how we're going to break that. We're going to break some arborist gear today.
What's it called? 10x tech and 5 eighths inch diameter. Yep, we've got an arborist harness
and we've got some prusik cords here and Jeremy Norman sent these to us and we're just going to
pull on stuff to have a little edutainment and hopefully you can learn something along the way.
Hopefully this isn't as strong as it looks because the machine only goes up to 50 or 100
kilonewtons depending if we do a two to one. But let's talk about this rope first and get
started on that and then we'll figure out how to break that because it's big and I actually
don't know how to do it. So Jeremy spliced some of these already for us but John Ferroni from
Extreme Gear, he is extremegear.org, he did some other splicing. Explain to us what you did on
yours. Sure, so what Jeremy did was he did a double fit length splice which is what Samson recommends.
I did a single fit length splice with a very short diagonal cut at the end on this one.
Because I wanted to see if it would slip if it's only one fit buried.
Yep and then on this one here again it's a proper splice with stitching and this has a
double locking brummel. I just made that term up. If I'm incorrect please yell at Ryan for that one.
You went in and brummel usually goes in like this and then out and splice. I think you went twice.
I went twice. On a lot of gear that has loops spliced into it you'll see a double
locking brummel. Almost like a daisy chain. Yeah exactly. So I wanted to see how that would work
and then there is a single fit length tail bury with a proper taper done on it. Now Jeremy sent
us pretty much new material here that's only been in a closet for a year for context and this is
Tek because it has two strands for each braid per carrier. This is designed for tree work. It's made
to splice really easy. It's very supple. It almost feels like Dyneema. Yeah that's why I was like I
can't break that and he's like don't know it's polyester. I think the load cell only goes up to
20,000. It has a 50. Well I can't pull more than 30,000. Anyways we'll find out how this goes.
He sells this on extremegear.org. Yeah. So you just started carrying Arborist gear. Yeah we
just started carrying Arborist gear. I've got all the major brands on there and more gears being
added just about every day. I'm working on organizing it a little bit better so the professional side
will have its own sub-domain on the website so you can find your gear that you need that's ANSI
rated and then there'll be the sport climbing side. Yep that's what we're trying to do on the
website right now is to organize it better because he has so much stuff on there. We just did a whole
buying guide. We're trying to add some other buying guides but if you guys buy the Arborist
gear from extremegear.org, I will reinvest the money the 10% from what you buy that goes to me.
I'll reinvest it back into more Arborist videos. I'm pretty stretched thin with the climbing,
slackline, caving, canyoning stuff but I definitely want to also serve the Arborist community because
your lives also depend on ropes and we like to break gear for all those uses. Invest in what
we're doing and I'll invest back into what you guys are doing. Let's start with breaking this
one. Sounds good. So I got 43 kilonewtons before basically our two-to-one which is what's going to
give me 100 kilonewtons got sucked up into our hydraulic there. So I'm gonna have to reset this
as tight as possible before it gets tight. So let's try this again. So we extended this all
the way out. I don't think it was this long when you did it. It stretched out probably 16 inches.
Yeah, that's a lot more. It's low stretch material but like by the time it settles,
it's faster. So it's pretty low stretch. Yep. Okay. Try number two. Success! Let's see how much
more throw we have left. Ah, not that much. All right. It did the helix thing. It left two strands
and it got melted that is. Oh yeah. Yeah. So technically this is one strand and but two
carriers. Yep. Wow, it's so fluffy. And all the tips are melted. It's a little crunchy on the top
on all of these. 77 kilonewtons. You know what that is in English? I know the rope is rated for
roughly 83 kilonewtons. Okay. We're pretty close because that's about a 10% reduction and when you
splice, you lose. You lose a little. A little bit. It's super good enough and it broke at the
end of the where the taper would be. Yep. On yours, not his. Yeah, it might be on mine. I don't know.
It's pretty close either way. It broke some of the stitching as it started to stretch. It tore
a few of the stitches. Now let's see if one fed slips or if it breaks like the last sample did.
Hold on. I never let go of that button and three seconds later have something break.
That's why we always back it off before we walk around the corner. That was really loud. So I was
out of throw pretty much like that's all that we had left. It looks like we only have one strand.
Yeah. Here's the second carrier for that one strand. That one broke. There's a lot of heat
involved in this. Oh yeah. I mean you can feel how warm the rope is. Basically one fit was
super good enough and you didn't have a locked brommel. No. Yeah. And it was a really short
taper. I just cut it with a pair of scissors. My tapers up here. This is the section that has no
taper and it broke. It broke over on his side. Okay. Okay. Wow. Considering you just cut yours
diagonal. Yep. I mean 85.2. So it started to do something right here and then I let go there and
it was settling and then popped. Dang. That's terrifying that that can happen. I mean that's
no small number to be messing with. No. And that's roughly two kilonewtons above the stated
breaking strength of that rope. Oh wow. So we hit a hundred percent. Oh wow. I'm sure glad I have
this thing. And you're standing where? Behind. I'm standing behind a shear, a cutoff saw, and two
pieces of stainless steel. Might be super good enough. The next two things we're going to break
are these two prusiks. So one is well used and one looks really new. We're going to just prusik
these around a half inch rope and if they don't break and the half inch rope does then we are
just going to pull these eye to eye to see if there's any difference between the new one and
used one. It was melting it was getting hotter and able to like grab more and it looks like it
broke the rope but not whoa whoa whoa feel that. Oh wow that's hot. That's really hot. It didn't
break it in the knot it broke it where it was just more or less pinching the shit out of it.
Oh yeah feel the tip it's completely melted or this one feel it's it's hard as a rock.
Yeah as if wow as if you took a um lighter to it. Yeah. So the first time it slipped was about
eight kilonewtons. We could throw an extra wrap in it so it slips less. Yeah. Instead of doing
three wraps up here we could do four. What really we were trying to test was this and I don't know
looks like it's freaking fine. So we wrapped it more. Let's try it again. Oh it only slipped once.
Whoa one or two extra wraps that's cool. So what's that 15 about 15 it slipped and then broke at
16.79. Oh look where it broke. Oh look at that in the knot. So it got quote unquote full strength
out of the rope. I mean this rope is old and used um but you know it didn't break here and that's
what we wanted to know. It's a little chafed but it's it's not bad. Still usable technically. Yeah
Should we just do them head to head? Yeah. You break the the sewing. Does that part? Nope. This
side looks to be just fine. Those are the plastic things that move to the middle
and that is very vectrin like. Now for the old one. Let's do it.
Oh wow the used one broke almost half. Yeah this one did not break at the sewn eye. It broke
farther down. Usually it breaks where like some junction or something is. I mean it looks pretty
well used. Okay so here's the harness. We are going to start by clipping uh this part here with the
arborist bridge and this looks super used enough and we're just clipping it right there.
That's so cool. Hey look I got a pulley out of it. Wow look how crappy it looks inside. Yeah this is
well used. Doesn't break at this knot. It breaks where the sharpest bend is. Oh it's going to break.
Oh that is close. 22 is about 10 times stronger than you'll ever need it. Because we tensioned
the knots the part that was not exposed came out. That's what it used to look like. We're going to
go from this point. This is the buckle that is on the leg loop and then we put this big soft shackle
as the connection for the back of the thigh and we're just going to see if it breaks here or if
it breaks the buckle is my guess. Buckle held and strap lost. That is what we got. Does the buckle
still work? Yep. Oh nice. That webbing I bet is breaking 50% of what it could break at if it was
new. It's not a sharp bend radius obviously but I think they're both shaped like that. Yeah but
you can see where they're really starting to wear through. Yeah that is the issue. I bet the other one looked
just like it. Okay here's the other leg loop and you can see that this thing is 25% cut through
from his wear and tear and so we're going to put that right on there and we're going to pull like
this even though it's kind of even pulling even worse and we're clipping the ring in the back
just to see if something happens interesting on this side. Oh that was low. It sounded low. That
was very low. Oh you called it. You said five before we did it. Yep. I mean five still stronger
than you in theory need it. Oh this is MBS 23 kilonewtons. Yeah I mean it broke. Shocker.
Any damage on the backside? Nothing. Nothing? Doesn't seem like much. Yeah these are all pretty
nice beefy attachment ring points like that's pretty cool. We're going to add those aluminum
rings to this little pile. Right here we have some welded steel rings. We have a titanium ring from
Titan Climbing. Two titanium rings. Some rolled aluminum repel rings and then we have like a forged
or cnc'd aluminum and then this was a well-used rolled aluminum one and so we're going to see
what that breaks at from the harness and we're going to break all these in another video so you
should subscribe. Our next configuration is a soft shackle between these two rings and this ring back
here and I'm assuming a soft good is going to break before those rings. Looks like two versus
one. Oh where's the one? So the ring is still here. It doesn't seem to be deformed. Back here this
stitching is what broke. Seems plenty good enough. Did you know the MBS of a harness is two guys
trying to harvest the rings off of it? So we cut it up too bad to break the waist belt but
it's pretty much the same straps on the whole thing that keep breaking but we're actually now
going to break a little bit of the hardware that goes with it now. We're going to test this buckle.
This is intended to not come undone when there's pressure on it. Click. Let's see what happens.
Ah it's rated for 15. Nice. It didn't break this part. It broke here. Oh yeah the pin that holds
the the locking mechanism blew out the sides of that. Yep. That's what that side looks like.
These are the the Cobra buckles made by the same company that makes the Pyrams.
Okay. Austria Alpen and the Rondo Carabiners. Gotcha. And you carry all that stuff? I do.
Cool. Let's see what this breaks at.
Oh it just it just rammed right through that metal. Sweet. So MBS is 23 kilonewtons.
Pretty good for a well-used unit. All right let's see what happens when you pull it sideways.
That's 960 frames per second by the way. So that's some pretty fast snapping. Oh. How did it?
Yeah I'm. What? Oh. Oh. Oh. Oh. Oh. Yeah. All right. I thought we magic happened.
Ah imagine that. What it's rated for. So this rigging plate swivel pulley is rated for 28
kilonewtons. No I'm not gonna break this but thanks for asking. Uh this looks really useful.
Tell us if you like us breaking Arborist gear. I try to throw you guys a bone every once in a while
but I am spread pretty thin. Go check out extremegear.org if you want to buy Arborist
gear and then we will do more stuff like this. Make sure you put in the comments what you
want to see tested next time I get a box of goodies and maybe some information about this
stuff that we didn't bring up because we don't know that much about it. Any other thoughts?
No. Buy your stuff. Says the store guy. Let me know if you like me branching out into Arborist
gear.